Page is loading ...
www.PTN-electronics.com
MHD44TP
PTN HDBaseT Matrix Switcher 4x4
All Rights Reserved
Version: MHD44TP20131.0
User Manual
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited www.PTN-electronics.com
NOTICE: Please read this user manual carefully before using this product.
Update History
Version
Date
Update Content
1.0
2013.05.29
First version.
This manual is only for operation instruction only, not for any maintenance usage.
The functions described in this version are updated till May 2013. Any changes of
functions and parameters since then will be informed separately. Please refer to the
dealers for the latest details.
This manual is copyright PTN Electronics Limited. All rights reserved. No part of
this publication may be copied or reproduced without the prior written consent of
PTN Electronics Limited.
All product function is valid till 2013-05-29.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited www.PTN-electronics.com
Table of Contents
1. Introduction ................................................................................................................. 1
1.1 Introduction to MHD44TP .................................................................................. 1
1.2 Features ............................................................................................................ 1
1.3 Package Contents ............................................................................................. 1
2. Product Appearance of MHD44TP .............................................................................. 2
2.1 Front Panel ........................................................................................................ 2
2.2 Rear Panel ......................................................................................................... 3
2.3 Connection with RS232 Communication Port .................................................... 4
2.4 Twisted Pair Cable Connection .......................................................................... 5
3. System Connection ..................................................................................................... 5
3.1 Usage Precautions ............................................................................................ 5
3.2 System Diagram ................................................................................................ 6
3.3 Connection Procedure ....................................................................................... 6
3.4 System Applications .......................................................................................... 7
4. Application Solution .................................................................................................... 7
5. System Operations ..................................................................................................... 9
5.1 Button Control .................................................................................................... 9
5.2 IR Control .......................................................................................................... 9
5.2.1 Usage of IR Remote .............................................................................. 10
5.2.2 IR Operations ........................................................................................ 10
5.3 RS232 Control ................................................................................................. 14
5.3.1 RS232 Commands ................................................................................ 14
5.3.2 Control MHD44TP ................................................................................. 18
5.3.3 Control 3rd-Party Device from Local ...................................................... 18
5.3.4 Bi-directional RS232 Control ................................................................. 18
5.4 TCP/IP Control................................................................................................. 18
5.4.1 Control Modes ....................................................................................... 18
5.4.2 TCP/IP Settings ..................................................................................... 20
5.5 USB Firmware Updating .................................................................................. 24
6. Specification ............................................................................................................. 25
7. Panel Drawing .......................................................................................................... 26
8. Troubleshooting & Maintenance ............................................................................... 26
9. Safety Operation Guide ............................................................................................ 27
10. After-sales Service .................................................................................................. 28
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 1 www.PTN-electronics.com
1. Introduction
1.1 Introduction to MHD44TP
MHD44TP is a 4x4 HDBaseT matrix switcher, including 4 HDMI inputs, 4 HDBaseT
outputs, 2 local HDMI outputs, 4 de-embedded stereo audio & 4 de-embedded digital
audio outputs. It enables cross-point switching from any input to any output, and
supports high resolution 1080P, HD3D. The HDBaseT output can works with
TPHD402PR, to transmit HDMI, IR, RS232 and POE over a Cat5e/Cat6 cable. And its
transmission distance can up to 60 meters.
1.2 Features
HDTV compatible with High Definition Transmission resolution up to
1920*1200@60Hz, supports 1080P@24Hz, 3D.
HDCP Compliant and DVI compatible, supporting HDMI 1.4a & DVI1.0.
Powerful EDID&HDCP management.
HDBaseT outputs, to transmit HDMI, IR&RS232 to 60 meters long distance over a
Cat5E/6 cable.
POE supports, provides power for all the receivers connected to HDBaseT outputs.
Supports multiple control ways, including front panel, RS232, IR and optional TCP/IP
control (works with PTNET).
IR OUT signal switching follow with video signal, also can be broken away from
video switching.
Supports remote control from receiver by IR&RS232.
Supports centralized IR control to control all the remote display devices.
Supports PCM, Dolby, and DTS5.1 surround.
LCD indicator shows connection status, switching status, HDCP status, and output
resolution.
1.3 Package Contents
1 x MHD44TP
2 x Mounting ears
1 x Power adapter (DC48V)
1 x IR remote
1 x Power cord
1 x RS232 cable
1 x CAT5e twisted pair
1 x IR converting cable
8 x Captive screw connectors
4 x Plastic cushions
1 x User manual
Notes：Please confirm if the product and the accessories are all included, if not, please
contact with the dealers.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 2 www.PTN-electronics.com
2. Product Appearance of MHD44TP
2.1 Front Panel
No.
Name
Description
①
Firmware
Micro USB port for update firmware.
②
Power
Indicator
Keep light when power on.
③
IR Receiver
Receive control signal from IR remote.
④
LCD
Indicator
Real-time shows system status.
⑤
INPUTS/
Menu
buttons
Normal mode: Input buttons, ranging from "1" to "4".
Inquire mode: Press “AV” more than 3 seconds to enter this
mode. to change different menus, to change
different channels.
⑥
Function
buttons
AV synchronal button: To transfer AV and IR signal (from IR
OUT port) synchronously by the switcher.
Note: The IR OUT port number is corresponding with HDMI
INPUTS port number as default.
Example: To transfer both AV and IR signals from input
channel No.1 to output channel No.3.
Operation: Press buttons in this order “1”, “AV”, “3”.
ALL outputs button: To transfer one input to all outputs.
Example: To transfer both AV and IR signals from input
channel No.1 to all output channels.
Operation: Press buttons in this order “1”, “ALL”
EDID management button: manually capture and copy the
EDID data from output device to input port.
Example: To capture and copy the EDID data from output
channel No.4 to input channel No.2.
Operation: Press buttons in this order “EDID”, “2”, “4”
Press button “2” in INPUTS area, “4” in OUTPUTS area.
⑦
OUTPUTS
Output buttons, ranging from "1" to "4".
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 3 www.PTN-electronics.com
With the front control panel, the switcher could be control directly and rapidly by
pressing the buttons under below format.
“Input Channel” + “AV” + “Output Channel”
“Input Channel”: Fill with the number of input channel to be controlled.
“Output Channel”: Fill with the number of output channels to be controlled.
2.2 Rear Panel
No.
Name
Description
①
IR ALL IN
IR control signal input port, connect with IR receiver, pass
through to all the HDBaseT ports to control the remote devices.
②
HDMI
INPUTS
HDMI input ports, 4 in total, type A female HDMI connector,
connect with HDMI input source devices.
③
IR OUT
Connect with IR emitter, to send out the IR signal from the
HDBaseT port of the far-end Receiver. These IR OUTs make
up an IR matrix with the IR INs on the HDBaseT receivers,
and all can be switched synchronously with the AV signal,
or separately switching.
④
OUTPUTS
IR IN: Connect with IR receiver, fixed IR input for the output,
cannot be switched separately. It makes up an IR
bi-directional transmission with the IR OUT on the
corresponding HDBaseT receiver.
HDMI: HDMI output port, connect with HDMI output devices.
To split HDMI output for local monitoring.
COAX: HDMI de-embedded digital audio output.
HDBaseT: Works with receivers using HDBaseT technology,
such as TPHD402R, TPHD402PR. It can pass through AV,
IR and RS232 signal to 60m distance. Meanwhile, it can
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 4 www.PTN-electronics.com
provide power for the receivers which support POE.
RS232: RS232 port to communicate with the RS232 port on
corresponding HDBaseT receiver. When controlled by
HDBaseT receiver, the communication protocol must be the
same with MHD44TP.
AUDIO: HDMI de-embedded stereo audio output
⑤
RS232
The serial port for unit control, 9-pin female connector,
connects with control device such as a PC.
⑥
Power
Indicator
Turn red and keep on when power on.
⑦
48V DC
Connect with 48V DV power adaptor.
⑧
GROUND
Connect to grounding, make the unit ground well.
⑨
TCP/IP
TCP/IP port for unit control, optional function.
⑩
IR EYE
Connect with extended IR receiver, use the IR remote to
control MHD44TP.
2.3 Connection with RS232 Communication Port
Except the front control panel, MHD44TP can be controlled by far-end control system
through the RS232 communication port. This RS232 communication port is a female
9-pin D connector. The definition of its pins is as the table below.
No. Pin Function
1 N/u Unused
2 Tx Transmit
3 Rx Receive
4 N/u Unused
5 Gnd Ground
6 N/u Unused
7 N/u Unused
8 N/u Unused
9 N/u Unused
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 5 www.PTN-electronics.com
2.4 Twisted Pair Cable Connection
The cables for HDBaseT ports must be straight-through ones, using T568A or T568B
standard.
3. System Connection
3.1 Usage Precautions
1) System should be installed in a clean environment and has a prop temperature and
humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safety.
3) All devices should be connected before power on.
TIA/EIA T568A
TIA/EIA T568B
Pin
Cable color
Pin
Cable color
1
green white
1
orange white
2
green
2
orange
3
orange white
3
green white
4
blue
4
blue
5
blue white
5
blue white
6
orange
6
green
7
brown white
7
brown white
8
brown
8
brown
1st Ground
4--5
1st Ground
4--5
2nd Ground
3--6
2nd Ground
1--2
3rd Group
1--2
3rd Group
3--6
4th Group
7--8
4th Group
7--8
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 6 www.PTN-electronics.com
3.2 System Diagram
3.3 Connection Procedure
1) Connect HDMI sources (e.g. DVD) to HDMI inputs of MHD44TP with HDMI cables.
2) Connect HDMI displayers (e.g. HDTV) to HDMI outputs of MHD44TP with HDMI
cables.
3) Connect speakers/earphones to AUDIO output ports (3p captive screw connectors).
4) Connect the HDBaseT port of HDBaseT receiver and MHD44TP with twisted pair.
5) Connect the RS232 port (9 pin female D) of MHD44TP with control device, e.g. PC.
6) Connect the RS232 port of controlled device to any other RS232 port (3p captive
screw connector) of MHD44TP. The control signal can be transmitted bi-directionally.
7) MHD44TP can be controlled by its built-in IR receiver or through the IR EYE port by
connecting with external IR receiver. The IR signal can also be transmitted
bi-directionally (connect IR OUT port of MHD44TP to IR IN port of other far-end IR
device, and connect IR IN ports of MHD44TP to IR OUT port of other far-end IR
device), and in this mode, we can control MHD44TP remotely.
Note: The IR IN port has built-in infrared carrier receiver.
8) Connect DC48V power adaptor to MHD44TP.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 7 www.PTN-electronics.com
3.4 System Applications
As its good performance in control and transmission, MHD44TP can be widely used in
computer realm, monitoring, large screen displaying, conference system, television
education and bank securities institutions etc.
4. Application Solution
Product Assortment Description:
① SC61D (mini scaler switcher)
6 video Inputs: 2 x HDMI, 1 x VGA, 1 x YPbPr, 1 x C-video & 1 x S-video.
Upscale to HDMI output at 1080P.
3 audio outputs: HDMI embedded audio, 3.5mm stereo audio and Coaxial (SPDIF).
Output resolutions selectable to assure preferred output.
Output display H/V size: adjustable to settle any overscale problem.
Output display H/V position moveable.
Picture/MP3 display via USB.
Video parameter setting and preset.
Powerful OSD function with full control, support output freeze function
Ultra-switching for instaneous display.
HDMI1.3 and HDCP compatible.
Firmware updatable via USB.
Front panel lockout.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 8 www.PTN-electronics.com
② PA3V (40W power amplifier)
Mono audio output at 40Watt.
Switchable between 70V and 100V.
Ducking function.
16 ID codes for controlling between different PA3V amplifiers.
3-level MIC input, supports condenser microphone, dynamic microphone and
wireless microphone.
MIC port can support balance/unbalance signal, suppress the external noise
effectively.
Two stereo audio inputs and one digital audio input, switchable by button, IR remote
& RS232.
Volume/Bass/Treble controllable by buttons, IR remote & RS232.
Fast switching speed for good performance.
Convection cooler, fan is not needed.
③ TPHD402P (HDMI/IR/RS232 POE twisted pair extender)
Support Full HD: Delivers high resolution image (1080p@60Hz@48
b/pixels/3D/4Kx2K).
Max transmission distance is up to 70 meters over single CAT5e/CAT6 cable.
HDTV Compatible, use HDMI 1.4 and HDCP compliant.
Support POE & CEC.
Connect with a displayer to transmit EDID and HPD signals constantly by using a
CAT5e cable.
Use HDBaseT technology.
Bi-directional RS232/IR control.
④ WP8 (control panel)
Every button can be programmed to send the bi-direction RS232 and RS485
commands simultaneously to control third party devices.
Every button can be programmed to send the infrared code, control the relay, to let
them work simultaneously to control the third party devices.
Every button is built in the infrared code and RS232 code learning function, and
baud-rate setting.
ID looping function. 99pcs WP8 can be looped and controlled together, by ID
identifying.
Programmed by USB or RS232, working with PTN PC software (PS-WP).
Crystal and backlit buttons with easy user-friendly customizable changeable labels.
The backlit brightness is controllable.
Dimension: 11.4cm long and 7cm wide.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 9 www.PTN-electronics.com
5. System Operations
5.1 Button Control
The operation examples are showed in 2.1 Front Panel. Here we make a brief
introduction to the system inquiry operations.
Keep pressing the button “AV” for 3 seconds, it will enter into system inquire menu. Use
Left and Right direction button two check the previous/next item.
Function Items
Example
Description
Check the
connection
status of inputs
Y means the corresponding port
is connected with input device, N
means not.
Check the
connection
status of outputs
Y means the corresponding port
is connected with output device,
N means not.
Correspondence
between inputs
and outputs
Shows the correspondence
between the 4 inputs and 4
outputs.
Check if the
input is with
HDCP
Y means the input signal is with
HDCP, N means not.
Check if the
output is with
HDCP
Y means the output signal is with
HDCP, N means not.
Check the
output resolution
Use the UP and DOWN direction
button to check all the 4 output
resolutions.
5.2 IR Control
By using IR & HDBaseT transmission technology, MHD44TP has some functions as
follows:
1) Control far-end output device from local.
2) Control local input/output device remotely.
3) Control MHD44TP locally/remotely.
MHD44TP can be controlled by its built-in IR receiver or through the IR EYE port by
connecting with extended IR receiver, or even can be controlled remotely by a far-end
IR device through the twisted pair.
Resolution
Out 1 1920x1080
Out 1 2 3 4
HDCP Y Y Y N
In 1 2 3 4
HDCP Y Y Y N
Out 1 2 3 4
Input 1 2 3 3
Out 1 2 3 4
Connect Y Y N N
In 1 2 3 4
Connect Y Y Y Y
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 10 www.PTN-electronics.com
5.2.1 Usage of IR Remote
5.2.2 IR Operations
1) IR Matrix Switching
The 4 “IR OUT” ports make up a 4x4 IR matrix with the “IR IN” ports of the far-end
receivers. See as below:
Input channels, range from 1~4, IR signal switched
following HDMI signal correspondingly.
Menu buttons, AV and ALL buttons have the same
function as the front panel. THROUGH: To transfer
the signals directly to the corresponding output
channels
Example: Press “3”, “THROUGH”, the result will be IN
3OUT 3. Press “ALL”, “THROUGH”, the result will
be: 11, 22, 33, 44
Output channels, range from 1~4.
Each channel has 1 IR IN, 1 COAX, 1 HDBaseT, 1
RS232, and 1 AUDIO outputs, and channel No.1 &
No.2 has 1 HDMI output.
Standby button, press it to enter in standby mode.
11
Control Local Devices or MHD44TP Remotely
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 12 www.PTN-electronics.com
The IR signal is received from corresponding remote controller, then transferred to
HDBaseT receiver, then to corresponding zone of MHD44TP through the twisted pair,
finally transferred to IR OUT port and received by controlled device.
Switching Operation:
a) Sending command, reference to 5.3 RS232 Control: [x1]R[x2].
x1: Corresponding to the 4 IR OUT ports of MHD44TP, The IR emitter connected to
this port can be placed at IR receiving area of output device or MHD44TP itself.
x2: Corresponding to the zone (receive IR signal from HDBaseT receiver with IR IN
port connects with IR receiver) number of MHD44TP.
E.g.: Command “3R2.” means to transfer IR signal received from zone 2 to IR OUT
port 3.
b) Using IR remote: Input channelbutton IROutput channel
Input channel: the 4 INPUTS buttons, corresponding to the 4 IR OUT ports of
MHD44TP.
Output channel: the 4 OUTPUTS buttons, corresponding to the zone (receive IR
signal from HDBaseT receiver with IR IN port connects to IR receiver) number of
MHD44TP.
E.g.: Press buttons “3”, “IR”, “1” in order, “3” in OUTPUTS area, “1” in INPUTS area,
to transfer IR signal received from zone 3 to IR OUT port 1.
Note: When switch all the 4 IR input signal channels to a same IR out channel,
it is not able to control the controlled device(s) at the same time.
2) IR Carrier Enforcing
a) Only if the IR receiver connected with HDBaseT receiver is with IR carrier, the
received IR signal can be transferred to IR OUT port of MHD44TP.
b) Only if the IR receiver connected with IR ALL IN port of MHD44TP is with IR carrier,
the received IR signal can be transferred to IR OUT port of MHD44TP.
If the IR receiver connected with HDBaseT receiver or IR ALL IN port of MHD44TP is
not with IR carrier, you need to send the command “%0901.”, and then you are able
to transfer the IR signal to IR OUT port.
3) IR Settings
When need to control a remote displayer from local, the IR receiver used must be with
IR carrier. The IR signal is transferred to the corresponding zone connected with the
HDBaseT receiver which is connected with the IR emitter. When the IR receiver is
connected to IR ALL IN port, the IR signal can be finally transferred to all the 4 IR
emitters connected with HDBaseT receivers.
As the figure below:
13
Control Remote Displayer from Local
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 14 www.PTN-electronics.com
4) Controlled by a Third-party IR Control Device
Use the included IR converting cable (see as below), connect the red end to IR input
port of MHD44TP, the black end to IR output port of the third-party control device. Then
the IR signal is able to be transmitted via the twisted pair, and finally gets to remote
output device.
5.3 RS232 Control
5.3.1 RS232 Commands
Through the RS232 communication port, user can control a far-end device whose
bound rate is 2400, 4800, 9600, 19200, 38400, 57600 or 115200. Default setting of
MHD44TP: bound rate is 9600, data bit is 8, stop bit is 1 and parity bit is none.
Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
Command
Types
Command
Codes
Functions
System
Command
/*Type;
Inquire the models information.
/%Lock;
Lock the front panel buttons on the Matrix.
/%Unlock;
Unlock the front panel buttons on the Matrix.
/^Version;
Inquire the version of firmware
/:MessageOff;
Turn off the feedback command from the com port. It
will only show the “Switch Ok”.
/:MessageOn;
Turn on the feedback command from the com port.
Demo.
Switch to the “demo” mode, 1->1, 2->2, 3->3 … and
so on .The switching interval is 2 seconds.
Undo.
To cancel the previous operation.
Operation
Command
(PTN2.0
Command
System）
[x]All.
Transfer signals from the input channel [x] to all
output channels
All#.
Transfer all input signals to the corresponding output
channels respectively.
All$.
Switch off all the output channels.
[x]#.
Transfer signals from the input channel [x] to the
output channel [x].
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 15 www.PTN-electronics.com
[x]$.
Switch off the output channel [x].
[x1] V[x2].
Transfer the AV signal from the input channel [x1] to
the output channel [x2].
[x1] B[x2].
Transfer the AV and IR signal from the input channel
[x1] to the output channel [x2].
Status.
Inquire the input channel to the output channels one
by one.
Save[X].
Save the present operation to the preset command
[X], ranges from 0 to 9.
Recall[Y].
Recall the preset command [Y].
Clear[Y].
Clear the preset command [Y].
PWON.
Work in normal mode.
PWOFF.
Enter into standby mode.
/%[Y]/[X]:[Z].
HDCP management command. [Y] is for input
(value: I) or output (value: O). [X] is the number of
one port, if the value of X is ALL, it means all ports.
[Z] is for working status (value: 1 or 0).
Y=I & Z=1, means the input port is compliant with
HDCP.
Y=O & Z=1, means output with HDCP.
Y=I & Z=0, means the input port is not compliant
with HDCP.
Y=O & Z=0, means output without HDCP.
[x1] R[x2].
Transfer the IR signal from the input channel [x1] to
the output channel [x2].
EDIDH[x]B[y].
Copy the EDID from output port [x] to input port [y].
If the EDID data is effective and the audio part
supports not only PCM mode, then force-set it to
PCM mode. If the EDID data is not effective, then set
it as initialized EDID data.
DigitAudioON[
x].
Enable HDMI audio output of port x.
X=1, 2, 3, 4, enable this one port.
X=5, enable all the 4 ports.
DigitAudioOF
F[x].
Disable HDMI audio output of port x.
X=1, 2, 3, 4, disable this one port.
X=5, disable all the 4 ports.
EDIDG[x].
Get EDID data from the output and display the
output port number of X.
EDIDMInit.
Recover the factory default EDID data.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 16 www.PTN-electronics.com
EDIDM[X]B[Y]
.
Manually EDID switching. Copy the EDID data of
output[X] to the input[Y].
EDIDUpgrade
[x].
Upgrade EDID data via the RS232 port
[X] is for input port, when the value of X is 5, it
means to upgrade to all input ports. When the
switcher gets the command, it will show a message
to send EDID file (.bin file). Operations will be
canceled after 10 seconds. (Note 1) Please cut off all
connections of HDBaseT ports.
%0801.
Automatically HDCP management. Input is with
HDCP, so is output.
%0800.
Manually HDCP management.
%0900.
Set as infrared carrier following mode.
%0901.
Set as infrared carrier enforcing mode.
%0911.
Reset to factory default.
%9951.
Check the command sent by port 1 when PWON.
%9952.
Check the command sent by port 2 when PWON.
%9953.
Check the command sent by port 3 when PWON.
%9954.
Check the command sent by port 4 when PWON.
%9955.
Check the command sent by port 1 when PWOFF.
%9956.
Check the command sent by port 2 when PWOFF.
%9957.
Check the command sent by port 3 when PWOFF.
%9958.
Check the command sent by port 4 when PWOFF.
%9961.
Check the system locking status.
%9962.
Check the status while in standby mode.
%9963.
Check the working mode of infrared carrier.
%9971.
Check the connection status of the inputs.
%9972.
Check the connection status of the outputs.
%9973.
Check the HDCP status of the inputs.
%9974.
Check the HDCP status of the outputs.
%9975.
Check the switching status.
%9976.
Check the output resolution.
HDBaseT Matrix Switcher 4x4
PTN Electronics Limited 17 www.PTN-electronics.com
/+[Y]/[X]:******.
Set communication between PC and HDBaseT
receiver.
① Y is for RS232 port (connect with RS232 port of
HDBaseT receiver)
Value = 1,2,3,4,5,A,B,C,D,E,F,G or H
The value of Y is defined into the following
meanings (in a given baud rate depended by the
value of X):
a. Y = 1, 2, 3 or 4, send this command to the
corresponding HDBaseT receiver to control
far-end device.
b. Y = 5, send this command to all HDBaseT
receivers to control all far-end devices.
c. Y = A, B, C or D
d. Y = E, F, G or H
For items c or d, send this command, it will be
saved to MHD44TP but taken without action to
corresponding HDBaseT receiver. And its
command function will be effective almost at the
same time when you send the command PWON
(for item c) or PWOFF (for item d).
Note:
A & E are for port 1.
B & F are for port 2.
C & G are for port 3.
D & H are for port 4.
② X is for bound rate (Value ranges from 1 to 7, 1
is for 2400, 2 for 4800, 3 for 9600, 4 for 19200, 5
for 38400, 6 for 57600 and 7 for 115200)
③ ***** is for data (max 48 Byte)
④ The symbol “.” is the end of one command. If
there are some symbols of “.” in one command,
this case is allowed and the last one is the end.
Note: 1. Please disconnect all the twisted pairs before sending command
EDIDUpgrade[X].
2. In above commands, “[”and “]” are symbols for easy reading and do not need
to be typed in actual operation.
3. Please remember to end the commands with the ending symbols “.” and “;”.
4. Type the command carefully, it is case-sensitive.
/