Equinox Systems Micro Batt EQLED160 User manual

Equinox Systems
Brand
Equinox Systems
Model
Micro Batt EQLED160
Category
Stroboscopes & disco lights
Type
User manual

This manual is also suitable for

Order codes:
EQLED160 - Black Housing
EQLED160A - White Housing
Micro Batt
User Manual
www.prolight.co.uk Micro Batt User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-
FULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Thisunitisnotintendedforxedinstallation.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.
www.prolight.co.uk Micro Batt User Manual
3
Micro Batt
Micro Batt
Power consumption 15W
Power supply 100~240V, 50/60Hz
Battery 12V 2200mAh
Dimensions 153 x 145 x 95mm
Weight 0.6kg
Order code EQLED160 - Black housing
EQLED160A - White housing
0m 1m 2m 3m 4m 5m
25° - Lux
FULL ON
R
G
B
W
1620
280
680
116
500
405
70
170
29
125
180
31.1
75.6
12.9
55.6
25°
101
17.5
42.5
7.25
31.3
64.8
11.2
27.2
4.64
20
145mm
153mm
95mm
*WARNING! Charging input only
via the approved charger supplied.
This must not be used with a
standard DC power supply.
01 - Hanging bracket
02 - Hanging bracket
adjustment knob
03 - LED display
04 - Function buttons
05 - On/off button
06 - 12V DC charging input*
07 - 3-Pin XLR DMX input
08 - 3-Pin XLR DMX output
In the box:
& 1 x user manual
MENU UP DOWN ENTER
DMX IN
POWER
DMX OUT
01
05
01
03
04
07 08
06
02 02
Rechargeable lithium battery powered LED slim par can utilising 1W RGBW
LEDs for stage or wall washing. The internal battery will keep a charge for
up to 6 hours from a single charge, and with no power cables to connect
you are free to set up the unit wherever you want. Function options and
DMX addressing can be changed using the 4 button LED display or
controlled by the supplied IR remote control, the units can also be run
master/slave. Utilising the on board menu system you can manually
colour select or colour mix providing a wide spectrum of colours.
• 12 x 1W LEDs (R: 3, G: 3, B: 3, W: 3)
• Beam angle: 25°
• 405 Lux @ 2m (full on)
• DMX channels: 8
• Static colour, colour change,
colour fade, strobe, sound active
and master/slave modes
• 0-1
00% dimming and variable strobe
• 4 push button menu with LED display
• Bracket allows for multiple rigging or
• Rechargeable battery
for wireless applications
• Maximum run time:
6 hours (single colour)
• Charging time: 5 hours (max.)
• DC 12V charging input
(via the included charger)
• 3-Pin XLR input/output
• Fan cooled
www.prolight.co.uk Micro Batt User Manual
4
Operating instructionsOperating instructions
MENU
Colour fade modes
A 3. 0 1
A 3. 3 2
A 3. 0 1
A 3. 0 1
A 3. 1 9
Sound active modes
A 4. 0 1
A 4. 0 4
A 4. 0 1
A 4. 0 1
A 4. 1 9
Strobe modes
A 5. 0 1
A 5. 3 2
A 5. 0 1
A 5. 0 1
A 5. 1 9
A 1. 0 1
Static colour mode
A 1. 0 1
A 1. 1 8
r .0 0 1
Manual mode (red)
r .0 0 1
r .2 5 5
G .0 0 1
Manual mode (green)
G .0 0 1
G .2 5 5
b .0 0 1
Manual mode (blue)
b .0 0 1
b .2 5 5
u .0 0 1
Manual mode (white)
u .0 0 1
u .2 5 5
A 2. 0 1
Colour change mode
A 2. 0 1
A 2. 3 2
DMX address settings
d 0 0 1
d 5 1 2
d 0 0 1
www.prolight.co.uk Micro Batt User Manual
5
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes
tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitof
thextureandeachxtureindependently.
ToaccesstheDMXaddressmode,pressthe“MENU”buttonontherearoftheunittoshow
d001ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstosettherequiredDMXaddress.Pressthe“ENTER”buttontoconrmthesetting.
Operating instructions
8 channel mode:
Channel Value Function
CH1
000-010 Nofunction
011-050 Staticcolourmode
051-100 Colourchangemode
101-150 Colourfademode
151-200 Soundactivemode
201-255 Strobemode
CH2
000-039 White(RGBW)
CH1
mustbe
011-050
040-049 Red
050-059 Green
060-069 Blue
070-079 Yellow
080-089 Cyan
090-099 Magenta
100-109 White
110-119 Yellow
120-129 Magenta
130-139 PastelRed
140-149 Cyan
150-159 PastelGreen
160-169 PastelBlue
170-179 PastelYellow
180-189 PastelMagenta
190-199 PastelCyan
200-209 White(RGB)
210-255 White(RGBW)
CH3 000-255 Speedadjustment
CH4 000-255 Masterdimmer(0-100%)
CH5 000-255 Red(0-100%)
CH6 000-255 Green(0-100%)
CH7 000-255 Blue(0-100%)
CH8 000-255 White(0-100%)
www.prolight.co.uk Micro Batt User Manual
6
Static colour mode:
Toaccessstaticcolourmode,pressthe“MENU”buttonontherearoftheunittoshowA1.01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselectthe
staticcolourrequiredbetweenA1.01~A1.18.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Colour change mode:
Toaccesscolourchangemode,pressthe“MENU”buttonontherearoftheunittoshowA2.01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
speedbetweenA2.01~A2.32.Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Colour fade modes:
Toaccessthecolourfademodes,pressthe“MENU”buttonontherearoftheunittoshowA3.01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselect
thefademodebetweenA3.01~A3.19.Pressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstoselectthefademodespeedbetweenA3.01~A3.32.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Sound modes:
Toaccessthesoundactivemodes,pressthe“MENU”buttonontherearoftheunittoshowA4.01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselect
thesoundmodebetweenA4.01~A4.19.Pressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstoselectthesoundmodesensitivitybetweenA4.01~A4.04.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Strobe modes:
Toaccessthestrobemodes,pressthe“MENU”buttonontherearoftheunittoshowA5.01
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstoselect
thestrobemodebetweenA5.01~A5.19.Pressthe“ENTER”buttonandusethe“UP”and“DOWN”
buttonstoselectthestrobemodespeedbetweenA5.01~A5.32.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
A1.01-White(RGBW)
A1.02-Red
A1.03-Green
A1.04-Blue
A1.05-Yellow
A1.06-Cyan
A1.07-Magenta
A1.08-White
A1.09-Yellow
A1.10-Magenta
A1.11-PastelRed
A1.12-Cyan
A1.13-PastelGreen
A1.14-PastelBlue
A1.15-PastelYellow
A1.16-PastelMagenta
A1.17-PastelCyan
A1.18-White(RGB)
www.prolight.co.uk Micro Batt User Manual
7
Operating instructions
Manual dimming mode:
Toaccessthemanualdimmingmode,pressthe“MENU”buttonuntilthedisplayshowsr.001onthe
LEDdisplay.Usethe“UP”and“DOWN”buttonstoselecttherequiredbrightnessofredfromr.000~
r.255.Pressthe“ENTER” buttonfollowedbythe“MENU”buttonandrepeatforg(green),b(blue)
andu(white).Pressthe“ENTER” buttontoconrmthesetting.
Value: 000 - 255 (000 = low brightness, 255 = high brightness)
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Master/slave mode:
Tosetthemasterunitselectyourdesiredprogram(staticcolour,colourchange,colourfade,sound
activeorstrobe.Tosettheotherunitsinslavemode,pressthe“MENU”buttononthefrontoftheunitto
showd001ontheLEDdisplay.Pressthe“ENTER”buttontoconrmthesetting.Theunitwillnowrun
insequencewiththemasterunit.Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
www.prolight.co.uk Micro Batt User Manual
8
Operating instructions
IR remote functions:
Button functions:
01-Setstheunitintoblackoutonoroff
02-Staticcolourmode-Usethe‘+’and‘-’buttonsto
selectthedesiredcolour
03-Colourchangemode-Usethe‘+’and‘-’buttonsto
selectthedesiredspeed
04-Colourfademodes-Usethe‘+’and‘-’buttonsto
selectthedesiredspeed
05-Soundactivemodes-Usethe‘+’and‘-’buttonsto
selectthedesiredspeed
06-Strobemodes-Usethe‘+’and‘-’buttonstoselect
thedesiredspeed
07-Setsthestaticcolour
08-Setsthespeedofcolourchange,colourfade,
soundactiveandstrobemodes
09-PutstheunitintoDMXmode-Usethe‘+’and
‘-’buttonstoselectthedesiredDMXaddress
SPEED
–
+
A1
DMX
–
+
COLOR
–
+
A2
A3 A5A4
02
04
01
05
03
06
07
08
09
www.prolight.co.uk Micro Batt User Manual
9
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m
www.prolight.co.uk Micro Batt User Manual
10
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL90, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.Itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
www.prolight.co.uk Micro Batt User Manual
11
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.
www.prolight.co.uk Micro Batt User Manual
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Equinox Systems Micro Batt EQLED160 User manual

Equinox Systems
Brand
Equinox Systems
Model
Micro Batt EQLED160
Category
Stroboscopes & disco lights
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents