Dante DN9131 Operating instructions

DN9131

H.264/MPEG4/MJPEG Video/Audio/Data

1 Channel Encoder/Server

Dual Stream

Installation and Operations Manual

Model Numbers: DN9131-1, DN9131-4

Description: H.264/MPEG4/MJPEG Encoder/Server

Dual Configurable Video Streams

with duplex Audio, Data, Alarms

Table of Contents

Table of Contents DN9131 IP Encoder/Server 2

1. Introduction 3

1.1. Features 3

2. Specifications 4

3. Installations and Operations 5

3.1 Package Content 5

3.2 Components 6

3.2.1 Front Panel 6

3.2.2 Rear Panel 7

3.3 Typical Connections 11

3.4 Serial Number / Mac Address 12

4. Operation Description 13

4.1. Factory Default Settings 13

4.2. Rebooting 13

5. Power over Ethernet (PoE) 14

5.1. PoE compatibility 14

5.2. Power classification 14

6. Electrical Characteristics 15

6.1. Operating conditions 15

6.2. Power consumption 15

7. Dimensions 16

Revision history 16

Quick Guide to Changing Encoder IP Address 17

1. Introduction

DN9131 compress video/audio data and transmit the compressed video,

audio, data through the network in real time. DN9131 provides a high

quality video image with limited bandwidth and storage capacity. These

products are ideally suited for a widerange of surveillance and remote

monitoring applications. Main features are highlighted below.

1.1 Features

Main features

• 1 Channel Video-Audio-Data Encoder/Server

• High Quality Compression in real time streaming

• DN9131 provides high quality H.264, MPEG-4, and MJPEG encoding at

up to D1 resolution in real time

Network

• 10 / 100 Base T

• RTP/RTSP and unicast/multicast are supported

Streaming

• Dual streaming mode, each configuable

Video/Audio

• Compatible with NTSC/PAL and BNC Composite output

• DN9131 supports two-way audio; G.711 compression

Power

• 12VDC and optional Power over Ethernet (PoE)

Additional Features

• Motion detection by hardware

• Burnt-in text

• RS-232C, RS-422/RS-485 Data

• USB 2.0 Port (2.0) external storage

• Micro SD Card socket for local recording

VCA

• VCA Presence (Included as Standard)

• VCA Surveillance (Optional)

2. Specifications

DN9131 Product Specifications

Digital Signal Processing:

TI Encoder with Reset Function

Video Impedance: BNC Composite Video Input 75 Ohm, BNC Looping Output

Video Compression: H.264/MPEG4/MJPEG, Dual Stream, Configurable

Video Resolution: D1, CIF, QCIF, QVGA, VGA

Video Frame Rate: 1 ~ 30 fps (NTSC), 1 ~ 25 fps (PAL)

Output Bit Rate: 128 Kbps ~ 4 Mbps

Bit Rate Control: Provides Variable Bit Rate (VBR) and Constant Bit Rate (CBR)

Audio Function: Audio Input / Audio Output; Terminal Block

Audio Impedance: Input 2.6V p-p typ, 3.3V p-p max; 8KHz and 16KHz sampling rates

Audio Compression: PCM and G.711

Network Interface: 10/100 Mbps RJ-45 Port; Status and Network LEDs

Wireless Network: 802.11b/g Wireless

Network Protocol:

TCP/IP, UDP/IP, HTTP, RTSP, RTCP, RTP/UDP, RTP/TCP, SNTP, DNS, UPnP,

SMTP, SOCK, IGMP, DHCP, FTP, DDNS, PPPoE, SSL v2/v3

Web Server: Intuitive Browser Interface

Operating System: Windows XP Pro; Optional Linux (Red Hat recommended)

CPU Requirement:

Intel Core 2 Duo 2GHz (standard NVR); Core 2 Quad 2.4GHz (analytics

NVR)

Remote Control: RS-232, RS-485/RS-422 PTZ Data; Terminal Block

Motion Detection: Supports Multiple Segments per Video

Alarm Functions:

2 Alarm In / 2 Alarm Out; NO/NC - Relay max. 24VAC 500mA or 12VDC

1A (+5V)

USB and micro SD Card: Supports 2.0 (external storage, back-up) / Local Recording

Power Supply: 12VDC, 240mA /mini Jack; Power over Ethernet (PoE)

Operating Temperature: 32°F ~ 140°F (0°C ~ 50°C)

Operating Humidity: 0-95% non-condensing

Dimensions L x W x H: 5.6” (141mm) X 4.1” (103mm) X 1.5” (38mm)

Weight: 12.5 oz (385g)

Material: Die Cast Aluminum

Regulatory Compliance: CE, FCC, ROHS

Manufactured to: ISO9001:2000 Standards

3. Installation and Configuration

3.1. Package contents

The Package contains the following. Please make sure all listed items are

included in the box.

DN9131------------------------------------------------------1

12VDC Adaptor---------------------------------------------1

LAN Cable (Cross Type 1.5m)-----------------------------1

9 Pin Terminal Block---------------------------------------2

100-240VAC Power Cable----------------------------------1

DN9131 LAN Cable

Cross type 1m cable

Terminal Block Plug Power Adapter

3.2. Components

3.2.1. Front Panel

Figure 1. Front Panel of DN9131

1 Video Input BNC Connector Vin

It is mainly used for CCTV camera inputs.

2 Video Output BNC Connector

Vout is composite video loop-out

3, 4 Indicator LED (Status, Data)

Status and Data indicators display the following system information.

Status LED has a yellow, a green and an orange color. Data LED has a

red, a green and a dark orange color.

1. Power off

Status Data

Power OFF OFF OFF

2. System initialization

Status Data

In Process Off Blinking Dark Orange

Normal State Orange Off

Abnormal State Orange Dark Orange

3. Kernel booting up

Status Data

In Process Orange Green

Normal State Orange Off

Abnormal State Orange Green

3

4

1

2

5

4. Video streaming

Status Data

Normal Blinking Green Off

Abnormal Green Off

5. DSP operation status

Status Data

Normal Orange blinks at every

1 second

Off

High Overload Orange blinks at every

1 second

Red

5 Micro SD Card Slot

Feature employed for local recording.

3.2.2. Rear Panel

Figure 2. Rear Panel of DN9131

1 USB Port

DN9131 provides one USB port which may connect to the USB device as

an external storage device and a wireless device. It can be connected to

multiple USB devices using USB HUB.

1

3

2 6

5

4

2 2 x 9 pin Terminal audio input/output, an alarm, a sensor, serial devices

Figure 3. Terminal block

Audio Input

DN9131 have one channel mono audio input.

Audio Output

DN9131 have one channel mono audio output. The audio output very

low-watt, therefore it requires amplifier speaker (Do not use headphone

/earphone directly)

Digital Alarm Input (DI1, DI2)

DN9131 supports two digital inputs. It can be connected either voltage

type sensor or relay type sensor as following Figure 4 and Figure 5.

Caution

!

Do not use voltage and relay type sensor together.

Please pay attention to electric characteristics during installation.

Figure 4. Voltage Type Digital Input Connection

AOut

AOut GND

DO ch1

DO ch2

DO GND

RS

-

485 D+

RS

-

485 D

-

RS

-

485 GND

DI GND

DI ch2

DI ch1

Ain GND

Ain

RS

-

232C GND

RS

-

232C TX

RS

-

232C

RX

ch1

ch2

GND

1

2

Sensor 1

Sensor 2

Figure 4. Relay Type Digital Input Connection

Please pay attention to electric characteristics during installation.

Digital Alarm Output (DO1, DO2)

DO devices can be connected as following Figure 5.

Figure 5. Digital Alarm Output Connection

Please pay attention to electric characteristics during installation.

ch1

ch2

GND

1

2

LED 1

LED 2

+12V

ch1

ch2

GND

1

2

Sensor 1

Sensor 2

RS-422/RS-485

The RS-485 serial port consists of DATA+, DATA- and GND as following

Figure 6.

Figure 6. RS-422 RS-485 Connection

RS-232C

RS-232C Terminal Block is used for some devices such as POS terminal block.

Figure 7. RS-232C Connection

3 LAN Connector (Ethernet)

This is a RJ-45 LAN connector for 10/100 Base-T Ethernet.

Figure 8. RJ-45 LAN connector

4 Power Adaptor Connector (DC 12V)

DN9131 employs a 12VDC 1A adapter for input power.

Figure 9. Power Connection

-

+

DATA+

DATA

-

GND

+

-

PTZ Camera

DATA+

DATA

-

GND

RX

TX

GND

RX

TX

RX

GND

5 LED Power Status Indicator

6 Reset Switch (Reset)

Reset switch is used for restarting DN9131 or resetting DN9131 as

Factory Default(FD). Refer to section 4.1 for detailed procedures.

3.3. Typical Connections

Figure 10. DN9131’s Front Panel Connection

Figure 11. DN9131s Rear Panel Connection

Normal operation may not be possible if temperature or

humidity exceed levels recommended in the specifications.

USB memory

LAN Cable

e

DC Adapter

Alarm

PTZ Camer

a

Amp Speake

r

MIC

External Monitor

C

amera

SD m

emor

y

Sensor 1

-

2

3.4 Serial Number / MAC Address

Serial number and MAC address is attached on the bottom of DN9131 as shown

in Figure 12.

Figure 12. Serial Number / MAC Address

MAC Address

Serial Number

550012345

MAC

00:13:23:01:23:45

DN9131

P1331010100000-121

4. Operation Description

4.1. Factory Default Settings

Factory default settings are set as follows:

• IP address: 192.168.xx.yy (refer to 2.3 Serial Number / MAC Address)

• Mask: 255.255.0.0

• Gateway: 192.168.0.1

• User ID: root

• Password: pass

xx yy xx yy

MAC address = 00-13-23-01-23-45 → IP address = 192.168.35.69

To Convert Hexadecimal numbers to Decimal numbers, use PC calculator.

In Calculator Menu:

1. Click View and select Scientific version

2. Next select Hex to convert digits xx - use keypad input number ex: 23

3. Next select Dec and get result = 35

4. Repeat for digits yy – select Hex, input number ex: 45

5. Next select Dec and get result = 69

To perform the FD (Factory Default) initialization:

1. Turn on the power (The status LED is on).

2. Press and hold the Reset button within 1 second.

3. Release the Reset button after 3 seconds.

4.2. Rebooting

To reboot the system:

1. While the camera is in use, press and hold the Reset button. (Both Status

and Network LEDs are on.)

2. Release the Reset button after 3 seconds.

Convert the Hexadecimal number to Decimal number

5. Power over Ethernet (PoE)

The PoE feature employed in DN9131 is available in model DN9131-4. The standard

units for power via 12VDC are models DN9131-1. For the detailed information, please

see Data Sheet on Series DN9131, 1 Channel Encoder/Server.

5.1. PoE compatibility

With non Power Sourcing Equipment (PSE)

When it is connected with non PSE, the power adaptor should be connected.

With power adaptor

Connecting both PSE and power adaptor does not do any harm to the products.

Disconnecting power adaptor while it is operating does not stop operation. The

product continues to work without rebooting.

5.2. Power classification

The PoE Power Class supported by DN9131 is Class 0.

Table 1 shows IEEE 802.3af power classes.

Class

Usage Minimum Power Levels

Output at the PSE

Maximum Power Levels at

the Powered Device

0 Default 15.4W 0.44 to 12.95W

1 Optional 4.0W 0.44 to 3.84W

2 Optional 7.0W 3.84 to 6.49W

3 Optional 15.4W 6.49 to 12.95W

4 Reserved for Future

Use

Treat as Class 0 Reserved for Future Use

Table 1. IEEE 802.3af PSE and Powered Device Power Classifications

6. Electrical Characteristics

6.1. Operating conditions

Parameters Min Typical Max Units

Audio input range 0.01 2.593 3.3 Vp-p

Ambient Operating Temperature 0 - 55 ºC

Ambient Operating Humidity 85 - 95 %

Table 2. Operating conditions

6.2. Power consumption

DN9131A

Input Voltage 12VDC

Current 120-240VAC

Consumption 240mA

Table 3. Power consumption

Overvoltage and overcurrent will cause a severe damage to the device or even

a fire.

7. Dimensions

H.264 Network Video Encoder

Status

Data

Vin Vout

1CH Encoder

SD

USB

DC12V

Ethernet

Reset

DI

2 Rx Tx1

RS-232

Ain

C

RS-485DO

21

Aout

1

Revision history

MANUAL#

DATE(M/D/Y)

COMMENTS

D1A.01 02/09/09 Created

D1A.02 02/1/09 Review and correct the error data

103.4

141.4

121.7

37.7

QUICK GUIDE FOR UPDATING IP ENCODER DN9131

Factory default settings are set as follows:

• IP address: 192.168.xx.yy (refer to 2.3 Serial Number / MAC Address)

• Mask: 255.255.0.0

• Gateway: 192.168.0.1

• User ID: root

• Password: pass

xx yy xx yy

MAC address = 00-13-23-01-23-45 → IP address = 192.168.35.69

To Convert Hexadecimal numbers to Decimal numbers, use PC calculator.

In Calculator Menu:

6. Click View and select Scientific version

7. Next select Hex to convert digits xx - use keypad input number ex: 23

8. Next select Dec and get result = 35

9. Repeat for digits yy – select Hex, input number ex: 45

10.Next select Dec and get result = 69

To change default IP settings to IP address compatible with your Network:

1. Go to Control Panel of you PC and click on Network and Internet Connections

2. Next click on Network Connections

3. Next right click on Local Area Connection and select Properties

4. Next Scroll down to Internet Protocol TCP/IP, select and click on Properties

5. Next Select “Use the following IP Address and if the default address is:

192.168.35.65 input into the box:

IP address 192.168.35.100 (last numbers higher than default)

Subnet Mask 255.255.0.0

Default Gateway 192.168.1.1

6. Next Click OK and wait 2 minutes for your PC to take on new IP address

7. Next go to Start and click on Run and type cmd

8. Next user must ping device to see that it reponds

Convert the Hexadecimal number to Decimal

number

9. In cmd prompt enter ping 192.168.35.69 (default IP address of DN9131)

If not detected in Network a screen apperas as (Request timed out:

10.If detected in Network a screen appears as Reply from IP address – using

example with 192.168.1.65

11. Return to Control Panel and follow procedures 1, 2, 3 and 4

12. Next Select “Obtain an IP address automatically

13. Next Click OK and wait 2 minutes for your PC to take on new IP

address

14. Use may open Internet explorer and type http://192.168.1.65/

15. Screen appears to indicate that the security of your PC is at risk

16. Select Continue to this website; open web browser of DN9131 Encoder

17. Click on Setup user name: root password: pass

18. If image vertical is jumping, select Video, Audio select Video-In

19. In Video-In select NTSC or PAL and click on Apply, wait 3 minutes

20. Next go to System Options to change the IP Address of Encoder

21. Select TCP/IP and input new IP address, click Apply, wait 3 minutes

22. Next ping device as in procedure # 9, if successful then

23. Use may open Internet explorer and type in new IP address selected

24. Screen appears to indicate that the security of your PC is at risk; Select

Continue to this website; open web browser of DN9131 Encoder

Dante DN9131 Operating instructions

This manual is also suitable for

Dante DN9131 Operating instructions

Related papers

Other documents