Video Tripod with Fluid Head
INSTRUCTION MANUAL
3/8" Screw Mounting Base
3/8" Thread for Accessories
Quick Release Plate Safety Button
Quick Release Plate
Pan Locking Lever
Tilt Locking Knob
Pan Bar Locking Lever
Leg Locking Knob
Rubber foot
Leg Brace
Detachable Pan Bar
Location of Components
2
1
3
4
5
6
7
8
9
10
11
●
3
●
2
●
1
●
4
●
5
●
6
●
7
●
8
●
9
●
10
●
11
Open the leg locks to adjust the
tripod to the desired height.
Extending Tripod Legs
1. If film head comes without mounting bowl: first screw
the bowl on the heads flat base and tighten the tree
locking screws on the bottom of the bowl, using an
Allen Key.
Mounting Film Heads on Video Tripod
2. Install the head with bowl
into the bowl-base of the
tripod and tighten the bowl
handle from beneath.
The Quick Release Plate can
be slid +/- 20mm to perfectly
balance Equipment.
Quick Release Plate
Due to an integrated safety button, Cayer film heads
prevent unintentional sliding out of the QR plate with
equipment.
Releasing and Installing a Quick Release Plate
1. Loosen the QR Plate Locking Lever, then press the
QR Plate Safety Button to release QR plate.
Note:
After placing the QR plate on the film head, make sure the
QR Plate Safety Button is back out to prevent equipment
from falling off.
2. Screw QR plate onto bottom of the camera, using
the mounting screw. Then slide back the camera with
QR plate onto film head. Slide the plate to balance
equipment properly and tighten QR Plate Locking
Lever.
QR Plate Locking Lever
QR Plate Safety Button
Unlocking the Tilt Locking Knob allows tilting +/- 90
degrees. Unlocking the Pan Locking Lever allows
360 degrees panning.
Tilt & Pan Adjustment
90°
360°
Move the lever half a turn forward or backward.
Release the locking lever to engage the teeth.
The lock can now be released or tightened.
Operating the QR Plate Locking Lever
Safety Instructions
Thank you for choosing a CAYER product. Please read
the safety instructions carefully before using the product.
The load capacity specified in the specifications
must not be exceeded.
Do not use the product in temperatures below
-20°C or above +70°C. Contact with seawater
is not recommended and may cause serious
damage.
Do not leave the product exposed to high temper-
atures for long periods without protection, e.g. in a
car at hot temperatures.
Ensure that the product is kept out of the reach of
children. Use it with extreme caution in hazardous
locations.
Do not scrub the spirit level, precision may be lost.
When transporting, remove photographic equipment
to prevent it from falling out.
Ensure that all fasteners are tightened and safety
catches engaged during work to prevent accidental
damage or injury.
Do not use lubricants. Regular lubrication is not
required.
Zhongshan Cayer Photographic Equipments Co.,Ltd.
The Third Industrial Zone,Tanzhou Town,ZhongshanCity,
Guangdong,China
Tel:+86-0760-86698849 Fax:+86-0760-86698849
E-Mail:sales@cayer.cn
Find us on
Facebook
www.cayer.cn
After use in wet, dirty or sandy environments, it is
recommended to clean and dry the product with a
soft cloth. Dirt, dust and sand in all closures and
threads should be removed after use. Clean only
with mild detergent or alcohol.
To be on the safe side, do not use or store the
product near electrical power sources and chemical
substances.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Promaster 24P Video Tripod Kit Owner's manual
-
Manfrotto 501HLV Datasheet
-
Vinten Vector 450 Operator Guide
-
Tiffen Steadicam Merlin 2 Specification
-
Vinten Vision 250 Datasheet
-
Miller Camera Support 1020 User manual
-
Benro A573TBS7 Installation guide
-
-
-
Celestron CGE Pro 925 Owner's manual
