Path Light Features:
Motion/Light Sensor: Light instantly turns on when it
detects motion from up to 12 feet away. The light sensor
conserves battery life by preventing the light from
activating in daylight.
Auto Shut-o: Light shuts o automatically after 20
seconds if no motion is detected.
Bright LED: 30 lumens cover up to 50 sq ft.
Durable, Weather Resistant: Tight seals and UV resistant
material allow the light to work in all weather conditions.
600 Beta Drive, Unit 100, Mayeld Village, OH 44143
877.298.9082
Installation Instructions
Compact Path Light
MB560
• 1 Small Screwdriver
• 4 AA-Cell Alkaline Batteries
(per light)
• 2 Screws
• 1 Stake
LED Light
Stake/
Mounting
Bracket
Stake/
Mounting
Bracket
Motion & Light
Sensor
NOTE: Light sensor only allows light to activate in darkness. We recommend you test in a dark room or closet.
What you need to install:
Thank you for purchasing the Mr Beams
®
Compact Path Light. We are committed to
eliminating darkness using the latest in Light-
Emitting Diodes (LEDs). LEDs are the most ecient
and durable light sources available. We are certain
that your light will contribute to a safer environment
and provide light where you need it at a very
reasonable cost.
What is included per light:
www.mrbeams.com
Tips:
•
Use only new alkaline AA-Cell batteries with 1.5V rating.
•
Do not mix old and new batteries. If batteries are not new, it may cause the light to malfunction.
•
Install batteries with polarity in correct position.
•
Light may activate when batteries are inserted. Simply take light into a dark room. Allow
batteries to settle, then test activation.
•
If your light will not turn o, it means that it is time to replace the batteries.
2. Twist screwdriver
counter clockwise to
remove screw from
bottom of light.
1. Light comes with stake
attached. Remove by
sliding light out of stake.
3. Remove battery compartment
lid by taking your index nger
and lifting the tab.
4. Insert 4 AA-Cell batteries
according to the position
indicated on the light.
5. Depress the battery lid
and twist screw back onto
light with screwdriver.
A. Determine location for
mounting light. Place
piece of wood on top
of stake and gently
hammer into ground
with a hammer or soft
mallet. Slide path light
into stake until it is
seated securely.
B.
Determine mounting
location. Drive two screws
(included) through holes
of mounting bracket. Once
mounted on wall, slide path
light down into stake until it
is securely seated.
Battery Installation
Mounting with Stake Mounting on Wall
* 1 year limited warranty. Visit site for details.
* Visit our website to view installation video.
Battery Caution:
1) Do not mix old and new batteries
2) Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium)
or (Nickel Metal Hydride) batteries
3) Do not dispose of batteries in re
4) Batteries should be recycled or disposed of as per state and local guidelines
A. Mounting with Stake
B. Mounting on Wall
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
JC Hammer EW0050 Installation guide
-
Mr Beams MB710-WHT-01-06 Installation guide
-
Mr Beams MB3100-BRN-01 Owner's manual
-
Mr Beams MB3100-BRN-01 User manual
-
Mr Beams MB596-BRN-06 Installation guide
-
Mr Beams MB982 Operating instructions
-
Mr Beams MB700 User manual
-
Mr Beams MB572 Installation guide
-
Mr Beams MB723 Operating instructions
-
Hampton Bay 435616-41HD Installation guide
