Atdec TH-40100-UF Installation guide

Atdec
Brand
Atdec
Model
TH-40100-UF
Type
Installation guide
Bits Bag
Component Checklist
Display Bracket (x2)
Wall Plate
Important Notes
TOOLS REQUIRED:

Power Drill

12mm (
1
/
2
”), 10mm (
3
/
8
”) or 7mm (
1
/
4
”) Drill Bit

Phillips Head Screw Driver

Spirit Level

17mm (
11
/
16
”) Socket Wrench or Shifter
Supports a maximum load of 150kgs (330lbs).
Suits displays with mounting hole patterns from 200mm to 800mm wide (8”-31.5”) by 200mm to 600mm
high (8”-23.5
”).
The manufacturer does not accept responsibility for incorrect installation.
Security Bracket
Mounting Screws
M8x15mm / M8x35mm / M8x45mm (x4 each)
M6x15mm / M6x35mm / M6x45mm (x4 each)
M5x15mm / M5x35mm / M5x45mm (x4 each)
M4x15mm / M4x35mm / M4x45mm (x4 each)
Cross Recessed Screws
Coach
Screw (x4)
Masonry Wall
Plug (x4)
Washer (x4)
Multi
Washer (x4)
Mounting the Wall Plate
A
13mm Spacer
Bush (x4)
20mm Spacer
Bush (x4)
Masonry Wall Timber Stud Wall
Note: Ensure the Wall Plate is mounted with the folded tabs point
upwards
Note: Ensure the Wall Plate is mounted with the folded tabs point
upwards
TIP: Use a spirit level to ensure the wall plate is horizontal TIP: Use a spirit level to ensure the wall plate is horizontal
Use a stud finder to precisely locate the timber stud and ensure that the
mounting holes are located in the centre of the stud
It is recommended when mounting directly into masonry wall, that the
mounting holes are positioned as far apart as possible.
12mm (0.5”) hole
Masonry Wall Plug
Wall Plate
Coach Screw Washer
7mm (0.25”) hole
Coach Screw Washer
Wall Plate
Timber stud
Installation Instructions
Flat Screen Wall Mount | Fixed
TH-40100-UF
Recessed Mounting Holes
B
C
Multi
Washer
M6 & M8
Screw Hole
M4 & M5
Screw Hole
Mounting
screw
When attaching the Brackets ensure
that both are vertically aligned.
Ensure that the tightest fitting hole
in the multi washer is used when
attaching the mounting screw.
E
For additional security, it is suggested that a Padlock is
attached through the Security Bracket and the Wall Plate
on either side as shown. The Padlock (not supplied) should
have a shackle diameter no larger than 5mm (
3
/
16
”).
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacture reserves the right to alter specifications without notice. Published: 12.12.13©
E.2.
E.1.
(not supplied)
With the Brackets attached
to the display, lift the display
and hook the brackets onto
the Wall Plate as shown.
There are three height
positions to choose from in
50mm (2”) increments.
Spacer
Bush
If the mounting holes are recessed
into the back of the display, use
the appropriate Spacer Bushes
provided to pack the recessed hole.
Please note the 13mm Spacer
Bushes can only be used with M4,
M5, and M6 Mounting screws.
Ensure the brackets are securely
fixed to the display.
  • Page 1 1
  • Page 2 2

Atdec TH-40100-UF Installation guide

Atdec
Brand
Atdec
Model
TH-40100-UF
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents