2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Bushwacker
  7. 14084

Bushwacker 14084 Installation guide

  • Hello! I've reviewed the installation instructions for the Bushwacker Trail Armor 14084 Corner Guards. This document provides a step-by-step guide on how to properly install these corner guards on your Jeep JL, including how to detach and reattach tail light assemble. I'm ready to answer any questions you might have about the installation process or the product itself.
  • What tools are needed for installation?
    What should I do before installation?
    What should not be used during installation?
    What is the first step to install the corner guard?
    What is included in the hardware kit?
    How many corner guards are installed using this instructions?
4325 HAMILTON MILL RD • BUFORD, GA 30518 • 800-241-7219 (USA AND CANADA) • FAX 800-438-37882
Bushwacker® only approves installing the Trail Armor according to
these written instructions with the hardware provided. WARNING:
Failure to install according to these instructions will invalidate the
warranty. This includes, but is not limited to using alternative installation
methods, hardware, or materials. DO NOT USE: Loctite, SuperGlue, or
similar products on the hardware or the ares.
Wash and completely dry the vehicle before installation. Dirt and debris
will negatively affect this product’s adhesion to the vehicle surface.
STEP 1 – PRIOR TO INSTALLATION
A)
B)
Jeep JL Trail Armor® Corner
Guard
• Cleaning cloth
• Screwdriver
• 10mm Nutdriver
TOOLS FOR EASY INSTALLATION:
• To claim a warranty, you must provide
Proof of Purchase.
LIMITED LIFETIME WARRANTY AGAINST
ANY MANUFACTURING DEFECTS
1.
Included in Hardware Kit:
ALCOHOL
PREP
PAD
2 pcs.
Set Part #14084
BW14084 Rev-0 06-20-2018
For complete tment info visit: www.bushwacker.com
The material that your product is made from can
be recycled. Please also consider recycling the
packaging that your product came in.
4325 HAMILTON MILL RD • BUFORD, GA 30518 • 800-241-7219 (USA AND CANADA) • FAX 800-438-37882
Installation Procedures
Beginning in the driver side rear corner, locate
the small plastic door that is covering the tail light
retaining bolt.
Open rear hatch.
Tail light retaining bolt exposed.Use a screwdriver to pry open the cover for the tail
light retaining bolt.
Use a 10mm nutdriver to remove the tail light
retaining bolt.
Carefully pull the tail light assembly away from the
vehicle.
21
5 6
3 4
4325 HAMILTON MILL RD • BUFORD, GA 30518 • 800-241-7219 (USA AND CANADA) • FAX 800-438-37882
Use a screwdriver to fully disconnect the wiring
harness and set tail light assembly aside.
Test t the Corner Guard in place. Take note of where
the red tape liner aligns with the vehicle body.
Clean the surface where the tape will contact the
vehicle body using the enclosed alcohol pads.
Carefully pull the red tail light harness release switch
in the direction indicated.
Position the Corner Guard in place and align with
the previously cleaned surface. Ensure that the red
tape pull tabs are all accessible. Apply pressure to
exposed tape.
Peel back 2” of red tape liner on all anges to expose
adhesive and create a pull tab.
7 8
910
11 12
4325 HAMILTON MILL RD • BUFORD, GA 30518 • 800-241-7219 (USA AND CANADA) • FAX 800-438-37882
With the Corner Guard in its nal position, begin
pulling tape tabs to remove remaining tape liners.
Proceed in a clockwise patter, beginning with the
upper left hand side as shown above.
Apply FIRM pressure to all anges to ensure proper
adhesion.
Repeat Steps 1 thru 15 to install passenger side
Trail Armor.
Reverse Steps 2 thru 8 to reinstall tail lamp
assembly.
13
15
14
16
/