Happy Health
Happy Ring
User Manual V1.3
11/28/2021
Ring Model: HHR2110
Charger Model: HHCH2110
Getting Started
1. Remove the Happy Ring and Charger from the product packaging
2. Connect the charger to the supplied USB cable and plug the other end of the
cable into a suitable USB-A outlet
3. Place the Happy Ring on the supplied charger to charge for at least 30 minutes
4. While the ring is charging, download and install the Happy Ring smartphone app
5. Once the ring has charged, remove it from the charger and place it on your finger
6. Open the Happy Ring smartphone app and follow the on screen instructions to
complete the setup process
Support
For all set up and product support questions, please contact the Happy Health support
team at the following address:
support@happy.ai
Safety Information
This product is not a medical device and should not be used to monitor, diagnose, treat,
or prevent any medical condition.
If you experience skin irritation following the use of this product, discontinue its use
immediately and contact a dermatologist.
This product is not a toy. Keep it away from children.
Do not expose this product to excessive heat. Do not attempt to cut open or puncture
this product.
RF Exposure Information:
This device is designed and manufactured not to exceed the exposure limits set forth for
an uncontrolled environment.
Regulatory Information
USA
This product contains a lithium-ion battery. Ensure that disposal complies with all local
laws and regulations.
FCC ID: 2A3JJ-HAPPY2110
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device contains a radio transmitter and receiver. It has been designed to not
exceed the RF exposure limits set by the FCC. Do not co-locate or use it in conjunction
with other transmitters or antennas.
Regulatory Information
Canada
Industry Canada ID: IC: 27894-HAPPY2110
IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en
CAN ICES-003 (B)/NMB-003(B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC Radiation Exposure Statement
This EUT is very low power and compliant with IC CNR-102 exemption requirements.
Ce MAE est très faible puissance et de la conformité aux exigences d'exemption IC
CNR-102.
Product Specifications
Outer ring material - High durability ceramic
Inner ring materials - Bio-compatible polymers and metals
Battery - Lithium polymer rechargeable (<1 W-hr)
Charging time - Approximately 2 hours
Connectivity - Bluetooth LE
Water resistance - Water resistant to 1m
Operating temperature - 0 to 55C / 32 to 131F
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Other documents
-
NARWAL YJCB012 User manual
-
NARWAL YJCC012 User manual
-
pebblebee PB-621-B Card Thin Rechargeable Item Finder Ultimate Tracker for Wallets or Narrow Spaces User manual
-
OnePlus 5 User manual
-
Happy Plugs Wireless II Black Gold Owner's manual
-
Tumi Z7RTUTWS User manual
-
TomTom GO DISCOVER User manual
-
Motorola Defy Satellite Link Rugged Handheld GPS Communicator User guide
-
CICLOSPORT CicloNavic 20 Owner's manual
-
Zebra DX30 Quick start guide
