K&H Travel Bike Basket User manual

Brand: K&H

Model: Travel Bike Basket

Type: User manual

Travel Bike Basket for Pet

Assembly Instructions

K&H Pet Products, Central Garden & Pet

Colorado Springs, CO

www.khpet.com l (719) 591-6950

Made in China

Thank you for purchasing the Travel Bike Basket for Pet by K&H Pet Products. When used properly,

your Travel Bike Basket should provide you and your pet years of comfortable and easy travel together.

SMALL Travel Bike Basket recommended for dogs up to 10 LBS. LARGE Travel Bike Basket recommended for dogs up to 20 LBS.

Take the product out of the box and lay all pieces on a at surface.

See Figure 1.

To mount your K&H Travel Bike Basket to your bike’s handlebars, rst locate

the black metal mounting bracket and hold it with the two curved metal sections

facing in the upright position as shown in Figure 2. The two curved sections at

the top will eventually rest onto your handlebars.

Next, locate the two, 3-inch rubber straps with the four holes in them and slide

one strap onto one of the curved end pieces of the mounting bracket. Make

sure you slide it through the very bottom 4th hole of the rubber strap.

See Figure 3. Repeat this step on the other side.

Once a rubber strap is on both sides, it is important to now position each of

them as shown in Figure

4 before moving on to step 5 below. These straps

will be used later on in the

installation process to help secure the metal mounting

bracket to your handlebars.

Next locate the two, 2.5-inch rubber handlebar protection guards and notice

there are openings on both ends. Feed one of the open ends of a rubber guard

onto one of the curved end pieces of the mounting bracket. See Figure 5.

For proper positioning, make sure that the open middle channel of the rubber

handlebar guard is in the upright position.

Continue to feed the rubber handlebar guard over the curved end piece and

then through the second hole on the other end of the handlebar guard as

shown in Figure 6. It should t snuggly against the underside curve in the

metal mounting bracket. Repeat this step on the other side. The nal and correct

resting position of the rubber handlebar guards is shown in Figure 7.

Next, nd the plastic extension piece that has the bolt through the center.

This extension piece will attach to the metal mounting bracket that you just

assembled. Holding the metal mounting bracket with the curves in the upright

position again, snap the plastic extension piece onto one of the 4 metal

horizontal crossbars as shown in Figure 8 & 9.

Please note that the plastic extension piece be can mounted two different

ways. It can be ipped either up or down on the horizontal crossbars

depending on which t works best for your individual bike. You have the

option to rotate the plastic extension piece 180 degrees LATER ON if needed.

See Figure 9.

Now with your bike stabilized, hang the two curved areas of the metal

mounting bracket over the FRONT of the handlebars making sure the

rubber handlebar guards stay in place and rest directly onto the handlebars.

These guards will help to keep the metal mounting bracket from slipping, and

also help to protect your handlebars. See Figure 10.

ASSEMBLY & INSTALLATION INSTRUCTIONS:

OVER

Figure 9 Figure 10

Option to

rotate plastic

extension

piece 180º

if needed

for

better

t later

Travel Bike Basket for Pet

Assembly Instructions - Page 2

K&H Pet Products, Central Garden & Pet

Colorado Springs, CO

www.khpet.com l (719) 591-6950

Made in China

IMPORTANT: At this time, the curved end of the plastic extension

piece should also rest comfortably across the curve of your bike’s head tube.

See Figure 11. TIP #1: You may need to experiment with moving the entire

plastic extension piece onto the different horizontal crossbars of the metal

mounting bracket until its curved end ts well up against the curve of your

bike’s head tube. TIP #2: You may also have to ip the plastic extension

piece upside down, (180 degrees), in order to nd the right t for your bike’s

head tube. Again, see Figure 9 for further instruction if needed.

Once the metal mounting bracket is resting on your handlebars and the extension

piece is snapped onto the mounting bracket in the proper place, hold rmly

against the handlebars and stretch one of the 3-inch rubber straps from earlier

around the UNDERNEATH side of the handlebar. Hook one of the open holes in

the rubber strap onto the corresponding curved metal end piece. See Figure 12.

Make sure this is stretched tight. Repeat this step on the other handlebar.

Locate the supplied wrench and tighten the nut on the plastic extension piece so

that it is snug, making sure to keep its curved end in place resting comfortably

along the curve of your bike’s head tube. See Figure 13.

Now it’s time to attach the K&H Travel Bike Basket to your bike. Slide the sturdy

opening on the back of the Bike Basket over the front of the bike mounting

bracket as shown in Figure 14. Slide down until the Bike Basket is resting

on the metal support piece located at the bottom of the mounting bracket.

Finally, there are two nylon straps on the Bike Basket that attach to your

handlebars to provide extra safety and support. On one side, wrap the nylon

strap around your handlebar and feed the end of the nylon strap through its

buckle as shown in Figure 15. Repeat this step on the other side. Now you

can make nal adjustments by tightening or loosening the straps against your

handlebars. Be careful not to impede or strap down any of your bike’s brake

cables or gear cables. Facing the front of your bike, the nylon straps and curved

ends of the metal mounting bracket that are now rubber strapped to your

handlebars should look like the image in Figure 16.

Lastly, attach the two leads located on the bottom inside of the Bike Basket to

your pet’s collar or harness to keep them securely inside of the Bike Basket at

all times. See Figure 17.

To detach the Bike Basket from the nylon straps on the handlebars,

simply squeeze the sides of the clasps to unfasten them. To remove the

Bike Basket simply lift the basket off of the mounting bracket.

Congratulations! You and your furry friend are now ready

to hit the bike path or cruise around town in your new K&H

Travel Bike Basket. Happy and safe riding together!

CONTINUED...

K&H Pet Products with design is a registered trademark of Central Garden & Pet Company.

CARE INSTRUCTIONS:

The cover is removable and machine washable. Line

drying is recommended. The outside can be wiped

clean with a damp cloth.

Figure 11 Figure 12

Figure 13

Figure 15

Figure 17

Figure 14

Figure 16

Finished!

Bike Head

Tube Front View of Bike

Plastic Extension

Piece

K&H Travel Bike Basket User manual

Brand: K&H

Model: Travel Bike Basket

Type: User manual

Download PDF

report

K&H Travel Bike Basket User manual

K&H Travel Bike Basket User manual

Related papers

Other documents