Panduit PN616C User manual

Brand: Panduit

Model: PN616C

Type: User manual

Panduit PN616C is a 4-channel above-floor raceway system designed for organizing and protecting electrical and data cables in various applications. With its modular design, it offers flexibility for customized configurations, allowing users to easily add or remove channels as needed. The system features a range of accessories, including couplers, end caps, junction boxes, and transition boots, enabling seamless integration with existing infrastructure and supporting various cable types.

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

The mounting hardware used to secure

the raceway shall be appropriate for the

mounting surface.

Screws provided with raceway are

intended for installation on a concrete

surface.

NOTES:

•An adhesive strip may serve only as a positioning aid during the installation process. The raceway shall be secured by mechanical

fastening means.

•Holes for mounting raceway and associated fittings should be predrilled into infrastructure prior to the installation of the mounting

hardware.

•A 5/32" concrete drill bit is needed for the provided concrete screws.

Above Floor Raceway 4-Channel Standard Product

Part Number(s): AFR4BC**%, AFR4RA**, AFR4TRT70**, AFR4JB2S**, AFR4EC**, AFR4CC**,

AFR4TBLG**, AFR4WTR**

14 12 10

0.111 0.13 0.164

Max Max Max Spec Max Spec Max Spec Max

40% 60% 40% 60% 40% 60%

OuterChannels(withscrewsinstalled) A 211510342334

InnerChannels B 241711352335

DataGradeCables

Cat6A

Fill

Cat6A(SD)

Fill

0.24

24AWG 24AWG

0.3

24AWG

Cat6

Fill

0.24

ElectricalCables

THN/THWN/T90

Fill

ULTempRiseTest

RacewayChannel SeeFig.

Page 1 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

BASE & COVER

0.3"

Screw to be no closer than

0.3" to inside latching rib

Space approximately 24"

3" maximum

COUPLER

Ensure coupler is fully

engaged with cover

Stagger base

joint and cover

coupling joint to

strengthen

assembly.

2 2a 3

1 2 2a 3 4

where ** denotes a color code and %

denotes a length in feet

RIGHT ANGLE

3 4

Page 2 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

TRANSITION TO T70

2345

END CAP

Ensure end cap and cover are fully engaged as shown. 0.3" is maxi-

mum allowable distance base can extend beyond cover when installing

cap.

0.3"

Page 3 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

JUNCTION BOX

Ensure end cap and

coupler(s) connect to

junction box cover as

shown [8 places]

Note: Junction Box can be assembled between two raceway paths with the use of two coupler fittings.

End cap installation shown as reference.

1" (25.4 mm)

Rectangular

Breakout 1/2" (12.7 mm)

Rectangular

Breakout

3/4" (19.05 mm)

Page 4 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

POWER/DATA APPLICATION DATA APPLICATION POWER APPLICATION 4

5 6

BREAKOUTS FOR CONDUIT APPLICATIONS

Page 5 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

GREENFIELD APPLICATIONS - NEW CONSTRUCTION

5/8”

1/2”

1/2"drywall application 5/8"drywall application

Stud Stud

Determine if you will use 1/2" or 5/8" drywall. Orient

standoff as shown for desired application.

Secure base to sole board and route

cables and wiring as desired. Do not

overtighten screws as flooring installa-

tion may require adjustments.

Adjust wall transition fitting base height

during flooring installation. After drywall

and flooring have been installed, secure

transition fitting base to the floor using

appropriate hardware.

Continue with Step 4 of Brownfield appli-

cation instructions.

**Only use standoff for Greenfield

applications**

If installing into existing infrastructure, con-

tinue to Brownfield application instructions.

WALL TRANSITION

BROWNFIELD APPLICATIONS - EXISTING INFRASTRUCTURE

1-1/2”

3-3/4”

6-1/2”

123

Cut hole in drywall between studs to the

dimensions shown.

Raceway

Cover

Raceway

Base

Page 6 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

TABLE LEG

3-1/4”

MEASURE

TABL E

HEIGHT

Raceway

Cover

Center of table leg transition fitting will sit approximately 3-1/4" from the edge of the raceway cover.

Route cables prior to installing the raceway cover.

NOTE: Desired hole in table should be offset from table leg center to accommodate proper

mounting of table leg.

O•

Made in PVC

USA

FT4

SUR FACE NONME TALLIC R ACE WA Y

68YL

600V MAX

Measure the height

from the floor to the

underside of the table.

Channel should be

between 3-1/2" to 4"

shorter than the mea-

sured height. If neces-

sary, cut channel from

bottom edge to accom-

modate.

INSTALLATION BETWEEN 2 RACEWAY CHANNELS

Page 7 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

Mounting

Bracket

Top of

Channel

Top Hole of

Channel

#10-32 Hex Nuts

#10-32 x 1" Screws

55A

Secure mounting bracket to top of channel using provided hardware.

Use the top hole of the channel for assembly. Do not fully tighten the

mounting bracket at this time.

Ensure couplers connect to bottom transition

boots as shown.

[4 Places]

Page 8 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

Capture Ledge

Bottom Edge of

Channel

Transition

Boot

#8-32 x 3/4"

Wood

Screws

[4 Places]

#10-32 Hex

Nuts

[2 Places]

#10-32 x 3/8"

Hex Screws

[2 Places]

Cover

[2 Places]

Stepped Flange

[2 Places] Transition Boot

Latch

[4 Places]

Top Transition Boot

[2 Places]

Mounting Bracket

Set bottom edge of channel on capture ledge of installed

transition boot. Connect second transition boot to the first.

Ensure channel is level.Secure mounting bracket to underside of table

using provided hardware. Fully tighten mounting bracket screws to

secure channel in place.

Route cables prior to installing covers. Covers are tamper-proof

and are not intended for easy removal.

If added stiffness is desired, secure bottom of channel using pro-

vided hardware in the lowermost holes of the channel.

Assemble top transition boots to each other. Transition boot latches will

mount to the stepped flanges of the mounting bracket.

Page 9 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

Page 10 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

INSTALLATION AS STAND ALONE OR WITH SINGLE SIDE RACEWAY CHANNEL

NOTE: For single side raceway application; above floor raceway should be mounted prior to table leg installation.

Center of table leg will sit approximately 3-1/4" from the edge of the raceway cover. Route cables prior to

installing the raceway cover.

NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg.

Page 11 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

O•

Made in PVC

USA

FT4

SUR F AC E N ON M E T AL LI C RACEWAY

68YL

600V MAX

Measure the height from

the floor to the underside

of the table. Channel

should be between 3-1/2"

and 4" shorter than mea-

sured height. If necessary,

cut channel from bottom

edge to accommodate.

MEASURE

TA B L E

HEIGHT

NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg.

Mounting

Bracket

Top of

Channel

Top Hole of

Channel

Bottom Hole

of Channel

[2 Places]

Bottom of

Channel

Mounting

Bracket

Page 12 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

Secure mounting brackets to top and bottom of channel using provided

hardware. Use the holes closest to the ends of the channel for assem-

bly. Do not fully tighten the mounting bracket at this time.

Pre-drill holes in infrastructure if necessary. Secure

bottom mounting bracket to floor with proper hard-

ware. (Concrete screws provided)

Ensure channel is level. Secure top mounting

bracket to underside of table using provided

hardware.

Transition Boot Latch

Ensure end cap(s) or

coupler(s) connect to

bottom transition

boots as shown

[4 places]

#8-32 x 3/4" Wood

Screws [4 Places]

4#10-32 Hex

Nuts

#10-32 x 1" Screws

Page 13 of 15

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

Capture

Ledge

Stepped

Flange

Bottom Edge of

Channel

Bottom

Transition

Boots

Covers

[2 Places]

Assemble bottom transition boots together. Transition boot

latches (shown in step 7) will mount to stepped flanges of the

mounting brackets. Place bottom of channel on top of cap-

ture ledge of transition boots.

Tighten all mounting bracket screws to the channel at this

time.

Route cables prior to installing covers. Covers are tamper

proof and are not intended for easy removal.

Stepped

Flange

[2 Places]

Transition

Boot

Latch

[4 Places]

Assemble top transition

boots to each other. Tran-

sition boot latches will

mount to the stepped

flanges of the mounting

bracket.

Page 14 of 15

INSTALLATION INSTRUCTIONS

E-mail:

techsupport@panduit.com

Phone:

866-405-6654

For Instructions in Local Languages

and Technical Support:

www.panduit.com www.panduit.com

Page 15 of 15

Panduit PN616C User manual

Panduit PN616C User manual

Panduit PN616C User manual

Related papers

Other documents