Rust-Oleum Automotive 251567 User guide

Brand
Rust-Oleum Automotive
Model
251567
Type
User guide

Rust-Oleum Automotive 251567 is a wax and tar remover that can be used to remove old wax build-up, grease, silicone and road film from automotive surfaces, including metal, plastic and fiberglass. It is also effective at removing tar. The product is easy to use: simply hold the can in an upright position approximately 8-12" from the surface and apply a liberal coat. Allow the product to stand for 1 minute and then wipe dry with a clean lint-free cloth.

Rust-Oleum Automotive 251567 is a wax and tar remover that can be used to remove old wax build-up, grease, silicone and road film from automotive surfaces, including metal, plastic and fiberglass. It is also effective at removing tar. The product is easy to use: simply hold the can in an upright position approximately 8-12" from the surface and apply a liberal coat. Allow the product to stand for 1 minute and then wipe dry with a clean lint-free cloth.

SPRAY TECHNICAL DATA ATO-34
AUTOMOTIVE
WAX & TAR REMOVER
Rust-Oleum Corporation Form: GDH-629
11 Hawthorn Parkway Phone: 877-385-8155 Rev: 010815
Vernon Hills, Illinois 60061 www.rustoleum.com
.DESCRIPTION AND USES .
Rust-Oleum
®
Wax & Tar Remover is an effective, fast-
acting remover for many automotive surfaces, including
metal, plastic and fiberglass. It should be used prior to
sanding to prolong the life of sandpaper and again after
sanding as a clean-up agent prior to applying top coats.
Wax & Tar Remover removes old wax build-up before re-
application of new wax to promote an even, mirror-like
finish. It is also great for removing grease, silicone
and road film.
.PRODUCTS .
SKU (13.5 oz. spray) Description
251567 Wax & Tar Remover
.PRODUCT APPLICATION .
APPLICATION
Protect hands with solvent-resistant gloves and eyes with
chemical splash goggles.
Hold can in an upright position approximately 8-12" from
surface with arrow on button pointed away from you. Apply
a liberal coat and allow to stand for 1 minute and wipe dry
with a clean lint-free cloth. Turn cloth frequently to ensure
a clean side contacts surface. Replace cloth as necessary.
NOTE: Works on most automotive metals, plastics and
fiberglass. This product may not be compatible with all
surfaces and all conditions surrounding application. Before
applying to any surface, always test product in a small
inconspicuous area to ensure no damage will result. Do
not use on freshly painted surfaces. Ensure paint has
cured in accordance with paint manufacturer’s instructions.
When using between paint coats, always follow the paint
manufacturer’s instructions regarding cure times. Do not
use on metal or plastic surfaces that are hot to the touch.
For best results, apply at temperatures between 65-90°F
(18-32°C) and avoid direct sunlight or strong breezes
.PHYSICAL PROPERTIES .
Physical Properties
WAX & TAR REMOVER
Composition
Aliphatic and Aromatic Hydrocarbons
MIR
1.60 Max
Fill Weight
13.5 ounces
Shelf Life
5 years
Flash Point
156°F (-104°C)
Safety Information
For additional information, see MSDS
The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements
of this literature do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our
materials are beyond our control, we can guarantee these products only to conform to our standards of quality, and our liability, if any, will be
limited to replacement of defective materials. All technical information is subject to change without notice.
  • Page 1 1

Rust-Oleum Automotive 251567 User guide

Brand
Rust-Oleum Automotive
Model
251567
Type
User guide

Rust-Oleum Automotive 251567 is a wax and tar remover that can be used to remove old wax build-up, grease, silicone and road film from automotive surfaces, including metal, plastic and fiberglass. It is also effective at removing tar. The product is easy to use: simply hold the can in an upright position approximately 8-12" from the surface and apply a liberal coat. Allow the product to stand for 1 minute and then wipe dry with a clean lint-free cloth.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents