Dometic MC402 Installation guide

Page is loading ...

MC402

7

Camera

blue

A + B

black

yellow

black

yellow

red

white

red

black

white

black

Rear

display

AV system

Radio

antenna

9

MC402-I-16s.book Seite 7 Freitag, 28. Oktober 2016 1:18 13

EN

MC402

8

Please read this instruction manual carefully before installation and first

use, and store it in a safe place. If you pass on the product to another

person, hand over this instruction manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

2 Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

6 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

7 Installing the moniceiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

9 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

10 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

11 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

MC402-I-16s.book Seite 8 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Explanation of symbols

9

1 Explanation of symbols

!

A

I

2 Safety information

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences and excess voltage

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

2.1 Safety when installing the device

Please observe the prescribed safety instructions and stipulations from the

vehicle manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which

could have as a consequence that:

• Cable fires occur

• The airbag is triggered

• Electronic control devices are damaged

• Electric functions fail (indicators, brake light, horn, ignition, lights)

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

MC402-I-16s.book Seite 9 Freitag, 28. Oktober 2016 1:18 13

EN

Safety information MC402

10

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative termi-

nal of the vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be

disconnected.

Please observe the following instructions:

• When working on the following cables, only use insulated cable lugs, plugs and

flat push-on receptacles:

– 30 (direct supply from positive battery terminal)

– 15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

• Use a crimping tool to connect the cables.

• When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

If you disconnect the negative terminal of the battery, all data stored in the volatile

memories will be lost.

• The following data must be set again, depending on the vehicle equipment

options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating

instructions.

Observe the following installation instructions:

!

CAUTION!

• Secure the parts installed in the vehicle in such a way that they cannot

become loose under any circumstances (sudden braking, accidents)

and cause injuries to the occupants of the vehicle.

MC402-I-16s.book Seite 10 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Safety information

11

• Secure any parts of the system covered by the bodywork in such a

manner that they cannot be come loose or damage other parts and

cables or impair vehicle functions (steering, pedals, etc).

• Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may

only be performed by qualified specialists.

A

NOTICE!

• To prevent damage when drilling, make sure there is sufficient space

on the other side for the drill head to come out.

• Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

• When testing the voltage in electrical cables, only use a diode test

lamp or a voltmeter.

Test lamps with an illuminant take up voltages which are too high and

which can damage the vehicle's electronic system.

• When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

• Insulate all connections.

• Secure the cables against mechanical wear with cable binders or insu-

lating tape, for example to existing cables.

2.2 Operating the device safely

!

WARNING!

• Never play videos while you are driving to avoid dangerous situations

in road traffic. Adhere to the country-specific laws and regulations.

• Only use the device in its function as a reversing video system while

driving. The driver must not look at the monitor under any circum-

stances while driving along. This could distract the driver and lead to

a serious accident.

• Adjust the volume of the device so that noise from traffic, particularly

horns and beeps, are still able to be heard.

MC402-I-16s.book Seite 11 Freitag, 28. Oktober 2016 1:18 13

EN

Safety information MC402

12

• Protect the device from humidity and moisture to prevent sparks, fire

or electric shocks.

• Switch off the device immediately

– if water gets into the device,

– if smoke is coming out of the device or

– if the device emits an unusual smell.

• This reader is certified according to the laser protection class 1. The

accessible laser radiation is safe under reasonably foreseeable

conditions. Avoid looking directly into the laser beam. Never open

the housing of the device. Do not make any repairs to the device.

Contact the manufacturer (see addresses on the back of the operating

manual).

I

NOTICE!

• If you use the monitor in vehicles, the vehicle should be running during

operation to prevent the vehicle battery from discharging.

• Only insert round discs into the device.

Do not use any other shaped discs.

• Only clean the discs with a soft, dry cloth from the middle to the outer

edge. To remove dirt, use a mild cleaning agent.

• New discs may have flaking on the edges. Remove these by carefully

running the side of a ballpoint pen around the edge.

• If the interior of the vehicle becomes too hot e.g. as a result of direct

sunlight, wait until the temperature has cooled down to the operating

temperature (under 60 °C).

MC402-I-16s.book Seite 12 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Scope of delivery

13

3Scope of delivery

4Accessories

Available as accessories (not included in the scope of delivery):

No. in

fig. 1, page 3

Quantity Description Ref. no.

1 1 Moniceiver 9600000350

2 1 2 DIN installation sleeve

3 1 Remote control (incl. batteries)

4 1 Cover frame

5 2 Fastening brackets

– 1 Display cleaning cloth

–1Stylus

– 1 Set of connection cables

– 1 Set of fastening material

– 1 GPS antenna

– 1 Installation manual

– 1 Brief instructions

Description Ref. no.

CAM18 NAV 9600000054

CAM50 NAV 9600000196

CAM80 NAV 9600000050

CAM44 NAV 9600000044

CAM30CK NAV 9102000050

CAM29BK NAV 9600000106

MC402-I-16s.book Seite 13 Freitag, 28. Oktober 2016 1:18 13

EN

Intended use MC402

14

5 Intended use

The moniceiver (ref. no. 9600000350) is intended for installation and use in a vehicle

with an on-board 12 Vg power supply and must be installed in a double DIN slot.

The device combines the functions of a car radio, CD player, DVD player, playback

device for external audio and video sources and a hands-free system for mobile

phones.

!

6 Technical description

The moniceiver is located in a housing which occupies two slots in the vehicle's

centre console.

The device can be connected to the handbrake switch. In this way, and for safety

reasons, no video can be played on the installed display while you are driving. The

display will only switch on if the vehicle is stationary and the handbrake is in use.

If a reversing video camera is connected to the moniceiver, then the device can be

set so that the camera automatically switches on when the reverse gear is engaged.

I

WARNING! Danger of death or serious injury.

• When using the device, ensure your are not distracted when driving

(e.g. connect MP3 player and selected playlist/radio station before

starting the journey, programme in pre-set buttons for different radio

stations if necessary).

• Observe the current laws and regulations of the country in which the

device is being used.

• Reversing video systems are designed merely as an additional aid for

reversing, however this does not relieve you of the duty to take

proper care when reversing.

NOTE

You can find the full technical description in the detailed installation and

operating manual on the internet under www.dometic.com.

MC402-I-16s.book Seite 14 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Installing the moniceiver

15

7 Installing the moniceiver

A

7.1 Notes on the electrical connection

Please observe the following instructions relating to the electrical connection:

• This device is intended for use only in vehicles with 12 Vg and negative earth.

Ensure that the vehicle has the required 12 V voltage before installing the device.

If no voltage of 12 Vg is available, then a voltage converter must be used.

• If the ignition socket of your vehicle does not have an ACC position (starter

battery), install a switch between the ACC cable and the power supply.

• If you have put in a new fuse, but faults still occur, then approach the

manufacturers (see addresses on back), the manufacturers' customer service

department or a similarly qualified individual.

• Ensure that all electrical connections and the loudspeaker cables are well

insulated in order to avoid short circuits.

• Ensure that the screws for protecting the device during transport (fig. 6 1

page 5) are removed from the upper side of the device prior to installation.

7.2 Installing and connecting the moniceiver

A

Observe the following installation instructions:

• When laying the cables, make sure:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection (fig. 3, page 3).

• Attach the cables securely in the vehicles to prevent tripping hazards. Use e.g.

cable binder, insulating tape or adhesive for this.

NOTICE! Beware of damage!

Before installing the monoceiver, remove the two screws used to

protect it during transport so that the DVD player can function.

NOTICE! Beware of damage!

• When drilling holes, check beforehand that there is sufficient space

on the other side for the drill head to come out.

• Cables and connections that are not properly installed will cause

malfunctions or damage to components. Correct installation of

cables and connections ensures lasting and trouble-free operation of

the retrofitted components.

MC402-I-16s.book Seite 15 Freitag, 28. Oktober 2016 1:18 13

EN

Installing the moniceiver MC402

16

• Check beforehand that there is sufficient space on the other side for the drill head

to come out (fig. 2, page 3).

• The device must not be fitted at an angle of more than 30° to the horizontal.

Otherwise, it cannot be guaranteed that the CD/DVD player will function cor-

rectly.

For the complete wiring diagram see fig. 9, page 7:

Label Description

TV TV antenna input

RADIO ANT Radio antenna input

A + B ISO plug

SWC Connection for steering wheel control

FRONT R Audio output (R) for front

FRONT L Audio output (L) for front

REAR R Audio output (R) for rear

REAR L Audio output (L) for rear

SUB OUT Connection for subwoofer

VIDEO OUT Video

TV BUS No function assigned

DAB BUS Connection for compatible DAB receiver

CAMERA IN Camera input

USB USB port

DVR BUS No function assigned

DVR VIDEO No function assigned

MIC Microphone for hands-free system

MC402-I-16s.book Seite 16 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Installing the moniceiver

17

Pin assignment see fig. 9 A+B, page 7:

To perform the installation and the electrical connection, proceed as follows:

➤ Disconnect the negative terminal of the battery.

➤ Remove any existing audio system.

➤ Install the 2 DIN installation sleeve (fig. 4, page 4).

➤ Bend the retaining tabs up, down and out at the sides in order to fix the housing

securely in the centre console (fig. 5, page 4).

➤ Attach the fastening brackets to the device with the fastening screws provided

(M5 X 6)(fig. 6, page 5).

➤ Connect the device to the electrical system in accordance with the circuit

diagram (fig. 9, page 7).

Label Description

Power and voltage connector

ACC Ignition switching plus (terminal 15)

GND Earth (terminal 31)

B+ +12 V battery

KEY A No function assigned

KEY B No function assigned

KEY GND No function assigned

BRAKE Handbrake switch

REVERSE Reversing light

Loudspeaker connection

– rear right (+)

– front right (+)

– front left (+)

– rear left (+)

– rear right (–)

– front right (–)

– front left (–)

– rear left (–)

MC402-I-16s.book Seite 17 Freitag, 28. Oktober 2016 1:18 13

EN

Troubleshooting MC402

18

➤ Conduct a function test before finally installing the device.

➤ Remove the two screws from the top of the device (fig. 6 1 page 5).

➤ Place the device into the slot and secure it with the fastening screws provided

(fig. 7 1 page 5).

➤ Fit the cover frame (fig. 8 1 page 6).

8 Troubleshooting

Problem Cause Remedy

The device will not switch on. The vehicle is not switched

on.

Switch the ignition to

ACC/ON or START.

The cables have not been

connected correctly.

Check whether the cables

are correctly connected.

The fuse is faulty. Replace the fuse with a new

one of the same type (5 A).

No sound. The volume is set to mini-

mum.

Check the volume.

The sound is muted. Switch the sound on again.

The reverse gear is engaged

when the reverse mute

function is activated.

If required, disable the

reverse mute function.

The device or display are not

functioning correctly.

The system is unstable (e.g.

the on-screen display is

frozen).

Reset the system by pressing

the RESET button.

The device will not play any

disks.

The disc has not been cor-

rectly inserted.

The disc must be inserted

with the label facing

upwards.

The disc is dirty or damaged. Clean the disc and check for

damage.

When the disc is playing, the

sound is interrupted by

vehicle vibrations.

The device has been fitted at

an angle of more than 30° to

the horizontal.

Fit the device at an angle of

under 30° to the horizontal.

Fit the unit so it is firm and

secure.

The radio receives no radio

stations.

The aerial is not properly

connected.

Connect the aerial correctly.

MC402-I-16s.book Seite 18 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Warranty

19

9Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the

addresses) or your retailer.

For repair and guarantee processing, please send the following items:

• Defect components

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

The radio reception is only

very weak.

The aerial is not fully

extended.

Extend the aerial fully.

The aerial is damaged. Check the aerial for damage

and replace if necessary.

The preset radio stations are

no longer stored when

restarting the radio.

The battery cable is not

properly connected.

Connect the battery cable

correctly.

The USB flash drive or

memory card cannot be

inserted.

The USB flash drive or

memory card have been

inserted the wrong way

round.

Insert the USB flash drive or

memory card the other way

round.

The USB flash drive or

memory card cannot be

read.

The NFTS format is not

supported.

Ensure that the USB flash

drive or memory card has the

FAT32 format.

Due to differences in formats,

some USB flash drives or

MP3 players cannot be read.

The remote control does not

function or does not function

correctly.

The batteries are weak or

empty.

Insert new batteries (type

CR2025, 3 V).

Problem Cause Remedy

MC402-I-16s.book Seite 19 Freitag, 28. Oktober 2016 1:18 13

EN

Disposal MC402

20

10 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever

possible.

M

If you wish to finally dispose of the product, ask your local recycling centre

or specialist dealer for details about how to do this in accordance with the

applicable disposal regulations.

B

Protect the environment!

Do not dispose of any batteries with general household waste.

Return defective or used batteries to your retailer or dispose of them at

collection points.

11 Technical data

I

NOTE

You can find additional technical data on the individual functions of the

moniceiver in the installation and operating manual on our website at

www.dometic.com.

PerfectView MC402

Item no.: 9600000350

Operating voltage: 12 Vg (10.5V–15.8V)

Max. operating voltage 15 A

Maximum output power: 40 W x 4 channels

Constant output power: 25 W x 4 channels

Operating temperature: –10 to 60 °C

at humidity levels of 45 % to 80 % RH

Storage temperature: –10 to 60 °C

at humidity of 30 % to 90 % RH

Dimensions W x H x D: 178 x 101.5 x 169 mm

Weight: approx. 1.9 kg

MC402-I-16s.book Seite 20 Freitag, 28. Oktober 2016 1:18 13

EN

MC402 Technical data

21

AUX IN

Audio

Video

Approvals

The device has E4 certification.

Distortion factor: ≤0.5 %

Frequency response (+3 dB): 20 Hz – 20 kHz

Audio input level: 0.5 Vrms

Input impedance 100 Ω

Input level: max. 2 Vrms

Input level (CVBS) 1.0±0.2 V

Input impedance 75 Ω

Output impedance 75 Ω

Output level 1.0 ± 0.2 V

4

MC402-I-16s.book Seite 21 Freitag, 28. Oktober 2016 1:18 13

Page is loading ...

YOUR LOCAL

SALES OFFICE

dometic.com/sales-oﬃces

YOUR LOCAL

DEALER

dometic.com/dealer

YOUR LOCAL

SUPPORT

dometic.com/contact

dometic.com

A

complete list of Dometic companies, which comprise the Dometic Group, can be found in the public ﬁlings of:

DOMETIC GROUP AB Hemvärnsgatan 15 SE-17154 Solna Sweden

4445101678 07/2019

Dometic MC402 Installation guide

This manual is also suitable for

Dometic MC402 Installation guide

in other languages

Related papers

Other documents