Black and Decker Appliances Spacemaker CG700 User manual

Brand: Black and Decker Appliances

Model: Spacemaker CG700

Category: Food processors

Type: User manual

This manual is also suitable for

Horizontal Toaster

Optima

Spacemaker

STOP

START

Spacemaker

Optima

™

Horizontal Toaster

SAVE THIS USE AND CARE BOOK

1-800-231-9786

QUESTIONS? Please call us TOLL FREE

MODEL T1000

*Trademark of General Electric Company, U.S.A.

When using electrical appliances, basic safety precautions should

always be followed, including the following:

READ ALL INSTRUCTIONS.

■ Do not touch hot surfaces. Use handles or knobs.

■ Do not operate any electric or gas heating appliance beneath this

unit. Do not place on or near a hot gas or electric burner or in a

heated oven.

■ Do not install the horizontal toaster over a sink or basin or any

electrical or gas heating appliance.

■ To protect against electrical shock, do not immerse cord, plug, or

any part of horizontal toaster in water or other liquid.

■ Close supervision is necessary when any appliance is used by or

near children.

■ Unplug from outlet when not in use and before cleaning. Allow to

cool before putting on or taking off parts, and before cleaning the

horizontal toaster.

■ Do not open crumb tray while horizontal toaster is in operation.

■ Do not operate any horizontal toaster with a damaged cord or plug

or after it has been damaged in any manner. Return horizontal

toaster to the nearest authorized service facility for examination,

repair, or adjustment.

■ The use of accessory attachments not recommended by the

appliance manufacturer may cause injuries.

■ Do not use outdoors.

■ Do not let the cord hang over the edge of table or counter, or

touch hot surfaces.

■ Plug the cord into the wall outlet. To disconnect, turn all controls

“OFF”, then remove the plug from the wall outlet. Do not yank on

the cord.

■ Do not use the horizontal toaster for other than intended use.

■ Oversized foods or utensils must not be inserted in the toaster, as

they may create a fire or risk of electric shock.

IMPORTANT SAFEGUARDS

Horizontal Toaster

Optima

Spacemaker

STOP

START

■ A fire may occur if the horizontal toaster is covered or touching

flammable material, including curtains, draperies, walls, and the

like, when in operation. Do not store any item on top of the

horizontal toaster when in operation.

■ Do not clean with metal scouring pads. Pieces can break off the

pad and touch electrical parts, creating a risk of electric shock.

■ Do not leave unattended while toasting.

■ Do not operate in the presence of explosive and/or flammable

fumes.

■ This product is intended for household use only and not for

commercial or industrial use.

SAVE THESE INSTRUCTIONS

11. Glass Door

12. Metal Lip (partially hidden)

13. Door Handle

14. Pull-Down Crumb Tray

(Under Unit)

15. Toasting Rack

16. Power On Light

17. Electronic Toast Control

Knob with Pastry Setting

18. Start Button

19. Stop Button

(Cancels Toasting)

10. Vents

11. 4 Plastic Washers

12. 4 Screws

13. 2 Mounting Brackets

14. Mounting Template

15. 2 Spacer Bars

16. 4 Nuts

17. 1 Cord Hook

These items are located

in the packing materials.

Check thoroughly before

discarding.

SAFETY NOTE: Overtoasting of thinly sliced

breads, reduced fat diet breads, and packaged

greasy toaster foods could cause them to catch on

fire. Toast thin, diet light, or greasy slices only in

lower settings of the Toast Color Control; for

packaged toaster foods, follow toasting instructions

provided by their manufacturers.

POLARIZED PLUG This horizontal toaster has a polarized plug — one

blade is wider than the other. To reduce the risk of

electric shock, this plug will fit into a polarized

outlet only one way. If the plug does not fit fully into

the outlet, reverse it. If it still does not fit, contact a

qualified electrician. Do not attempt to defeat this

safety feature by modifying the plug in any way.

CHOOSING A Your Spacemaker* Optima

Horizontal Toaster is

MOUNTING designed to be mounted under a cabinet. DO NOT

LOCATION ATTEMPT TO OPERATE UNLESS THE UNIT IS

PROPERLY INSTALLED. It can be mounted to

wood or metal cabinets. When choosing a

mounting location:

■ Keep in mind that it fits your normal work

pattern - especially the use of counter top

appliances and the possible addition of other

under-the cabinet appliances.

■ Hold the Toaster in various locations while you

consider the most convenient location for

mounting in your kitchen.

■ Do not install the Toaster over another cooking

or heating appliance or behind, under, or in front

of under-cabinet lighting appliances.

How to Use

*Trademark of General Electric Company, U.S.A.

■ Do not install the Toaster directly in front of an

electrical outlet, but be sure it is mounted within

reach of an electrical outlet.

■ The Toaster is designed to be mounted directly

next to any other Spacemaker* Optima

product,

with a clearance of at least 1” between the two

products. If it is not mounted next to any other

Spacemaker* Optima

product, maintain at least

a 5” clearance on all sides including the back.

NOTE: If you have Flush Bottom cabinets—a flat

level surface where the cabinet doors come to the

bottom of the cabinet front—(See Illustration 1A

page 6) please take note that the Metal Lip of the

Toaster should not be placed anywhere under the

hinge area of two cabinet doors.

If you are mounting the Horizontal Toaster directly

next to another Spacemaker* Optima

product

that is already mounted:

1. Place the Mounting Template along the side of

the already-mounted Spacemaker* Optima

pro-

duct that your Horizontal Toaster will hang next to.

2. Using the Mounting Template edge as a guide,

draw a line on the underside of the cabinet.

(Figure A) This will be the line to use to mark the

edge of the Horizontal Toaster’s location.

NOTE: To help determine

mounting location, see page 24

for the lengths of all the

Spacemaker* Optima

products.

Figure A

*Trademark of General Electric Company, U.S.A.

INSTALLING YOUR HORIZONTAL

TOASTER

Tools you will need for

installation:

• Drill and 1/4” drill bit

• Phillips screwdriver

• Hammer/Nail to start a drill hole

• Adhesive tape

• Eye Protection Goggles

• Newspaper to cover

counter tops (optional)

First, determine if your cabinet has

a flush bottom or overhang bottom.

(See Illustration 1A & 1B). If your

cabinet has a flush bottom — flat,

level surface — follow the

mounting instructions below. If

your cabinet has an overhang — a

lip extending below the bottom of

the cabinet shelf — turn to page 9

for mounting instructions.

MOUNTING INSTRUCTIONS

FOR CABINET WITH FLUSH

BOTTOM

1. Empty your cabinet of its

contents before starting to drill.

Clean the underside of the

cabinet to remove any grease or

other residue.

2. With the doors of the cabinet

open, place the front of the

Mounting Template even with the

front of the cabinet. (Figure B)

Tape securely in place.

3. Mark the four drill holes

through the Template onto the

cabinet bottom with a pencil and

Overhang Bottom-1B

Flush bottom-1A

Figure B

remove the Mounting Template.

(Figure C)

4. Cover the counter top to catch

drilled wood chips.

CAUTION: Suitable eye

protection is recommended to

prevent injury from shavings

while using a drill.

5. Make a small starter hole by

hammering a nail or using a

smaller drill bit. Holding the drill

straight and vertical at the hole

marks, center and drill up

through the bottom of the

cabinet. (Figure D)

6. Insert a plastic washer on

each screw with the flat side of

the washer resting on the

cabinet bottom. Drop each screw

with the washer in place through

a drilled hole from inside the

cabinet. Repeat the procedure

with remaining screws and

washers. Thread a nut onto each

screw so that approximately 1/4”

of the screw is exposed beyond

the nut. (Figure E)

7. Slide the Mounting Bracket

above the nuts through the

U-shaped openings on the

Bracket. The Bracket will then be

resting on the nuts. (Figure F)

(See page 8).

Figure D

Figure E

Figure C

8. Press the Bracket inward

and forward toward the front

of the cabinet until it stops.

Tighten the screw/nut assem-

bly with a screwdriver until

the Bracket just touches the

bottom of the cabinet. (Figure

G) The Bracket should move

freely front to rear in the slot

to fine tune the fit of the

Toaster to the cabinet front.

Repeat Steps 7 and 8 for the

other Bracket.

9. Hold the Toaster in front of

you and push it forward into

the slots on the Mounting

Brackets until it locks into

place. The Metal Lip on the

top of the Toaster must rest

against the cabinet front. (See

Figure H) The front of the

Toaster will extend 1

⁄2" beyond

the front of the cabinet.

10. Drape the Cord toward an

electrical outlet and use the

Cord Hook to hold it out of the

way. Peel the paper off the

adhesive back of the Cord

Hook. Place the Cord Hook at

the back edge of the cabinet

(on or next to the wall) over

the outlet to be used.

NOTE:

For safety, NEVER USE

TACKS THROUGH OR AGAINST

THE CORD TO HOLD IT.

Figure H

Figure G

Figure F

MOUNTING INSTRUCTIONS FOR

CABINET WITH OVERHANG

If your cabinet has an overhang —

a lip extending below the bottom of

the cabinet shelf — follow these

simple mounting instructions.

1. Empty your cabinet of its contents

before starting to drill. Clean the

underside of the cabinet to remove

any grease or other residue.

2. To determine whether you need

to use Spacer Bars to mount your

Horizontal Toaster, use the

Cabinet Overhang Ruler on your

Mounting Template and measure

the cabinet overhang (See

Illustration 2). If the overhang

measures 1/4”, 3/4”,1-1/4”, or 1-

3/4” inches, you will need Spacer

Bars. Instructions for using

Spacer Bars are on page 12.

NOTE: If The Mounting Location

Has A Partition: The Mounting

Template must be cut and a piece

removed to allow for this partition.

(Figure I) Measure and cut very

carefully. Save any pieces of the

Mounting Template you remove.

3. Fold down the grey strip on the

Mounting Template at the dotted

line.

4. With the doors of the cabinet

open, position the Mounting

Template under the cabinet so

Figure I

Illustration 2

the folded grey strip is against

the back of the cabinet overhang.

Tape the Mounting Template

securely in place. Check to be

sure the Mounting Template is

located where you plan to mount

the toaster.

NOTE: If the cabinet has an

overhang that extends more than

2 inches below the cabinet

bottom, a wooden shim (a piece

of wood that fits between the

Cabinet and the Bracket) will be

necessary. Cut a block of wood

that is: 16 1/4” x 5 1/2”. Make sure

the wood is at least as thick as

the amount of the overhang that

exceeds 2 inches. Locate and

drill holes on the shim for the

screws to pass through. (Longer

screws may be needed. See

Note after Step # 7.)

5. Mark the four drill holes

through the Template onto the

cabinet bottom with a pencil and

remove the Mounting Template.

(Figure J)

Cover the counter top to catch

drilled wood chips.

CAUTION: Suitable eye

protection is recommended to

prevent injury from shavings

while using a drill.

Figure J

6. Make a small starter hole by

hammering a nail or using a

smaller drill bit. Holding the drill

straight and vertical at the hole

marks, center and drill up

through the bottom of the

cabinet. (Figure K)

7. Insert a plastic washer on

each screw with the flat side of

the washer resting on the

cabinet bottom. Drop each

screw with the washer in place

through a drilled hole from inside

the cabinet. Repeat the proce-

dure with remaining screws and

washers. Thread a nut onto each

screw so that approximately 1/4

of the screw is exposed beyond

the nut. (Figure L)

NOTE: If it was necessary to use a wood shim

(See NOTE after Step #4), you may need to use

screws longer than those provided. To deter-

mine this, hold the shim firmly against the under-

side of the cabinet. Drop one of the screws

provided through the cabinet shelf and the shim.

Check to see that at least 1/2 inch of the screw is

visible to provide secure mounting. If it is not, you

will need #10-24 flat head machine screws. The

length of the screws should equal at least the

thickness of the cabinet floor PLUS the thickness

of the shim PLUS 1/2 inch. These screws can be

obtained at a hardware store.

Figure K

Figure L

8. If you determined you need

Spacer Bars (See Step # 2, page

9), place the Spacer Bars on top of

each Bracket so that the 2 small

tabs on the bars fit into the

notches on the Brackets. Slide the

Mounting Bracket and Spacer

Bars above the nuts through the

U-shaped openings on the

Bracket. The Bracket will then be

resting on the nuts. (Figure M)

9. Push the Spacer Bars/Bracket

up against the screws and

forward toward the front of the

cabinet. Tighten the screw/nut

assembly with a screwdriver until

the Spacer Bars/Bracket just

touches the bottom of the cabinet.

(Figure N) The Bracket should

move freely front to rear in the slot

to fine tune the fit of the Toaster to

the cabinet front. Repeat Steps 8

and 9 for the other Bracket.

10. Hold the Toaster in front of you

and push it forward into the slots

on the Mounting Brackets until it

locks into place. The Metal Lip on

the top of the Toaster should rest

against the cabinet front. (Figure

O) The front of the Toaster will

extend 1

⁄2" beyond the front of the

cabinet.

Figure O

Figure N

Figure M

11. Drape the Cord toward an

electrical outlet and use the Cord

Hook to hold the Cord out of the

way. Peel the paper off the

adhesive back of the Cord Hook.

For the most attractive

appearance, place the Cord Hook

at the back edge of the cabinet

(on or next to the wall) over the

outlet to be used.

NOTE: For safety, NEVER USE

TACKS THROUGH OR AGAINST

THE CORD TO HOLD IT.

USING THE NOTE: The Horizontal Toaster must be

TOASTER mounted before using.

A NOTE ABOUT THE TOASTER: This toaster is

designed with a special setting for pastry and a

range of settings — light to dark — for toast.

1. Plug the cord into a standard electrical

outlet. This Toaster is equipped with electronic

toasting, which means consistent toasting

performance for each setting. Adjust the

Electronic Toast Control Knob to the desired

setting - Light to Dark or Pastry.

2. For first use, set the Toast Control at Medium.

Readjust for lighter or darker toasting. All

breads/pastries do not toast alike. For example,

thinner, dry bread requires a lighter setting

than thicker, fresh bread. See the “Toasting

Guide” on page 14 for recommended settings.

(Continued on page 16)

TOASTING GUIDE

Electronic Toast Control Knob Guide

Pastry Light Medium Dark

RECOMMENDED

FOOD No. of SLICES SETTING*

White Bread, soft type 2 Slices Medium

1 Slice Light

Wheat Bread 2 Slices Medium

1 Slice Medium

Rye Bread 2 Slices Dark

1 Slice Medium

Variety Bread, Hand Sliced, 1 Slice Medium

3/4” thick

Italian Bread, 3/4” thick 2 Slices Light

French Bread, 3/4” thick 2 Slices Light

Portuguese Bread, 6-8” long, 1 Slice Medium

1/2” thick

Thin Slice White Bread 2 Slices Medium

1 Slice Light

Fresh Bagel 2 Halves Dark

Frozen Bagel (thawed) 2 Halves Medium

English Muffins 2 Halves Dark

Toaster Waffles 2 Sections Light

Toaster Breakfast Pastry 2 Pastries Pastry

French Toast 2 Slices Medium

Toaster Corn Muffins 2 Muffins Light

Pop Tarts 1-2 Tarts Pastry

Homemade Pound Cake, 3/4” thick 2 Slices Pastry

Toaster Hash Browns 2 Sections Medium

* Some adjustments may be necessary due to differences in bread and individual preferences.

Questions on Using the Horizontal Toaster

1. Can I toast thick slices of homemade breads?

Yes, as long as the slices don’t go over the

MAX FILL LINE. You can see the words

MAX FILL LINE and the line when you pull

open the door. It is not recommended to

put foods in the toaster that exceed the

MAX line.

2. I noticed some moisture on the glass

door—is that normal?

Yes. Some condensation may form on the door during the toasting

cycle because the door traps the heat and moisture. This is normal.

3. Can I interrupt a toasting cycle once it’

s started?

Yes. Push the “Stop” button and the cycle will stop. If you use a

second toasting cycle, watch for doneness and use “Stop” to stop the

cycle and avoid burning. You should use a lower setting for a second

toast cycle.

4. What do I do if my toast burns and starts flaming

The door of this toaster has an added benefit should flaming occur.

Since it traps the flames, the door helps extinguish any fire within a

short time. DO NOT open the door until the flames go out. Allow the

toaster to cool before removing burnt food.

5. Can I put butter or margarine on my food before toasting?

Yes. You can use a very thin layer of butter or margarine before

toasting. Be sure to use a setting of Medium or Light. Some dripping

may occur. Avoid using sugary toppings such as jellies, preserves, or

syrups in the toaster since they get very hot and may burn.

6. Pop-up toasters usually indicate one slot or the other for toasting

one slice. What is the best position for toasting one slice in this

toaster? For the most even heating and toasting, place the food in the

center of the toasting rack. Use lower settings for a single slice of toast.

(See the “Toasting Guide” on page 14.)

7. Can I reheat foods (i.e. Danish, a slice of pizza) on aluminum foil

in the toaster? No. This toaster should only be used with traditional

toaster-style foods. No foods should be heated in foil or on trays.

8. What is the best way to clean crumbs out of the door area

Remove the rack and sweep crumbs out with a pastry brush. If you

don’t have a pastry brush, use a dry paper towel and wipe clean.

STOP

START

MAX

FILL

LINE

3. Pull the handle down until

the door is fully opened and

latched. The Slide-Out Rack

will come forward. Place the

slices of bread or toaster

foods on the Rack. Use the

Door Handle to gently close

the door. (Figure P)

NOTE: For best toasting

results, use the MAX FILL

LINE located on the metal

border inside the Glass Door

as a guide to food height. It

is not recommended to toast

foods that rise above the

MAX line because toasting

quality will be affected.

4. Press the Start Button and

the Power On Light will

glow. Once the Toasting

cycle has been completed, a

signal bell will ring. Pull the

door handle down until the

door is opened and latched.

The Power On Light will go

off and the Rack will move

forward to present your

food.

5. For your safety, use a

potholder or utensil to

remove toasted food.

6. To stop the toasting cycle

at any time during it’s

operation, press the “Stop”

Button and the Power On

Light will turn off.

Figure P

NOTE: Always unplug the

cord from the electrical

outlet and allow the Toaster

to cool before cleaning.

DO NOT IMMERSE

TOASTER IN WATER

1. The See-Through Glass

Door should be cleaned with

a damp, sudsy cloth. Dry

thoroughly before using

the Toaster.

2. To clean the Slide-Out

Rack, pull the handle down

until the door is fully opened

and latched. Grasp the rack,

lift it slightly over the rack

pins and pull outward.

(Figure Q) Wash the Rack in

hot, sudsy water. To remove

stubborn spots, use a

polyester or nylon mesh pad,

and dry thoroughly before

replacing in the Toaster. To

replace, tilt the rack slightly

downward to fit through the

rack guides at the back of

the Toaster. (See Illustration

3) Drop the rack down over

the rack pins and close the

Door.

Care Guide

Figure Q

Illustration 3

CLEANING

NOTE: The Pull-Down Crumb

Tray can be extremely hot.

Allow it to cool completely

before cleaning.

3. Check and clean the Pull-

Down Crumb Tray often.

(Figure R) Immediately wipe

away any food crumbs or

spills from fillings or

toppings before next use.

Place a waste receptacle

under the Crumb Tray. Open

the Crumb Tray to empty the

crumbs. Use a cloth or

plastic scouring pad and hot,

sudsy water to clean the

tray.

4. Dry the Pull-Down Crumb

Tray thoroughly before

latching to the toaster. DO

NOT ATTEMPT TO OPERATE

THE TOASTER WITHOUT

CLOSING THE PULL-DOWN

CRUMB TRAY.

5. Clean the outside of the

Toaster with a slightly damp

cloth, then dry thoroughly

with a dry cloth. When

cleaning the outer shell,

NEVER USE STRONG

CLEANERS OR ABRASIVES

THAT WILL SCRATCH THE

SURFACES. Never spray or

apply cleaner directly to the

Toaster.

Figure R

The cord length of this Horizontal Toaster was

selected to reduce safety hazards that may occur

with a longer cord. If more cord length is needed,

an extension cord may be used. It should be

rated not less than 10 amperes, 120 volts, and

should have Underwriters Laboratories listing. A

properly rated extension cord with a polarized

plug may be purchased from a Black & Decker

(U.S.) Inc., Household Appliance Company-

Owned or Authorized Service Center. When using

a longer cord, be sure that it does not drape over

a working area or dangle where it could be pulled

on or tripped over.

Service, if necessary, must be performed by a

Black & Decker (U.S.) Inc., Household Appliance

Company-Owned or Authorized Service Center.

The Service Center nearest you can usually be

found in the yellow pages of your phone book

under “Electric Appliances-Small-Repairing.”

For your convenience, a complete listing of

our Company-Owned Service Centers can be

found on pages 21 & 22. To remove the unit for

service or repair, grasp the toaster on both sides,

lift up, and pull forward.

If mailing or shipping the Horizontal Toaster,

pack it carefully into a sturdy carton with enough

packing material to prevent damage. The original

carton is not suitable for mailing. Include a note

describing the problem to our Service Center

and be sure to give your return address. We

also suggest that you insure the package for

your protection.

TIPS ABOUT THE

ELECTRICAL CORD

SERVICE OR

REPAIR?

Need Help?

Black & Decker (U.S.) Inc. warrants this product

against any defects that are due to faulty

material or workmanship for a two-year period

after the original date of consumer purchase or

receipt as a gift. This warranty does not include

damage to the product resulting from accident

or misuse.

If the product should become defective within

the warranty period, we will repair it or elect to

replace it free of charge, including free return

transportation, provided it is delivered prepaid

to any Black & Decker (U.S.) Inc., Household

Appliance Company-Owned or Authorized

Service Center.

This warranty gives you specific legal rights, and

you may also have other rights which vary from

state to state.

Answers to any questions regarding warranty or

service locations may be obtained by calling toll-

free 800-231-9786 or by writing:

Consumer Assistance and Information

Black & Decker (U.S.) Inc.

626 Hanover Pike

Hampstead, MD 21074-0618

FULL

TWO-YEAR

WARRANTY

Page is loading ...

Black and Decker Appliances Spacemaker CG700 User manual

Brand: Black and Decker Appliances

Model: Spacemaker CG700

Category: Food processors

Type: User manual

This manual is also suitable for

Download PDF

report

Black and Decker Appliances Spacemaker CG700 User manual

This manual is also suitable for

Black and Decker Appliances Spacemaker CG700 User manual

Related papers

Other documents