CRITICAL DIMENSIONS
(DO NOT SCALE)
Specifications
FOR MORE INFORMATION CALL: 1-800-BUY-MOEN
www.moen.com
NOTE: 50/50 or metal waste assembly models are
designed to be installed through 3 - 1” dia. holes 2” on
center Models less waste assembly are designed to
install through 2 - 1” min. dia. holes 4” on center
DESCRIPTION
• Metal construction with various finishes identified by suffix
• 1/2" IPS connections
• Includes metal pop-up type waste assembly
OPERATION
• Knob style handles
• Rotate either handle counterclockwise to open
and clockwise to close
FLOW
• Flow is limited to 1.5 gpm max (5.7L/min) at 60 psi,
for products made before October 2008 flow is limited to
2.2 gpm max (8.3 L/min)
CARTRIDGE
• 1224 cartridge design
• Nonmetallic and stainless steel material
STANDARDS
• Third party certified to: WaterSense,® CSA B-125.1, ASME
A112.18.1 and all applicable requirements referenced therein
• Certified to ANSI/NSF 61/9
• Complies with California Proposition 65 and with the
Federal Safe Water Drinking Act
WARRANTY
• Lifetime limited warranty against leaks, drips and
finish defects to the original consumer purchaser
• 5 year warranty if used in commercial installations
2-9/32"
(57mm)
2"
(50mm)
2"
(50mm)
HOT
1/2" NPT INLET
COLD
1/2" NPT INLET
ESCUTCHEON DIA.
6-1/4" x 2-19/32"
(159mm x 66 mm)
3/4" (19mm)
MAX. DECK
THICKNESS
3-11/32"
(85mm)
6-9/64"
(156mm)
1-13/64"
(30mm)
3-3/16"
(80mm)
4-11/32"
(110mm)
CHATEAU®
Two-Handle 4” Lavatory Faucet
With Metal Wast
e Assembly
Model: 4920 series
With 50/50 Waste Assembly
Bulk Pack Model (12 per Carton):
64920 series, 64919 series
L
ess Waste Assembly
Model: 4900
Bulk Pack (12 per Carton):
64900
There is more than 1 version of this model.
Page down to identify the version you have.
Rev. 6/08
CRITICAL DIMENSIONS
(DO NOT SCALE)
Specifications
H
C
FOR MORE INFORMATION CALL: 1-800-BUY-MOEN
www.moen.com
NOTE: THIS FAUCET IS DESIGNED TO BE I
NSTALLED THRU 3 HOLES, 1" MIN. DIA.
DESCRIPTION
• Metal construction with various finishes identified by suffix
• 1/2" IPS connections
• Includes metal pop-up type waste assembly
OPERATION
• Knob style handles
• Rotate either handle in a counterclockwise manner to open
and clockwise to close
FLOW
• Flow is limited to 1.5 gpm max (5.7L/min) at 60 psi,
for products made before October 2008 flow is limited to
2.2 gpm max (8.3 L/min)
CARTRIDGE
• 1224 cartridge design
• Nonmetallic and stainless steel material
STANDARDS
• Third party certified to WaterSense,® CSA B-125 and
ASME A112.18.1M and all applicable requirements
referenced therein.
• Certified to ANSI/NSF 61/9
• Complies with California Proposition 65 and with
the Federal Safe Water Drinking Act
WARRANTY
• Lifetime limited warranty against leaks, drips and
finish defects to the original consumer purchaser
• 5 year warranty if used in commercial installations
2"
(51mm)
COLD
1/2" NPT
INLET
HOT
1/2" NPT
INLET
3-1/4"
(83mm)
MOUNTING
NUT/WASHER
3/4"(19mm)MAX.
DECK THICKNESS
DECK
GASKET
3-9/32"
(83mm)
CHAIN
STAY
13/16" (21mm)
O.D. SHANK
(2) PLACES
1-17/32"(39mm)
2-3/4"
(70mm)
5"(127mm)
1-1/4"(32mm)
2"
(51mm)
LIFT
ROD
CHATEAU®
4” Lavatory Faucet
with Metal Waste Assembly
Models: 4920 series
Rev. 10/01
/