Bendix
®
Trailer Information Module (TIM
™
) G2
User Guide
User Manual
Navigation Buttons
Moves menu cursor down. Short hold jumps down one position, long hold
jumps to end of list (Exit).
Moves menu cursor up. Short hold jumps up one position, long hold jumps to
top of list.
Selects menu item at cursor position.
Cursor Function display
Menu point has no sub menu.
Menu point contains a sub menu or an item that may be modifi ed.
Navigation Buttons and Functionality
Using the Navigation Buttons
User Manual
Navigation Buttons
Moves menu cursor down. Short hold jumps down one position, long hold
jumps to end of list (Exit).
Moves menu cursor up. Short hold jumps up one position, long hold jumps to
top of list.
Selects menu item at cursor position.
Cursor Function display
Menu point has no sub menu.
Menu point contains a sub menu or an item that may be modifi ed.
Navigation Buttons and Functionality
The cursor is at a point with no sub menu.
The cursor is at a point with a sub menu or
an item that may be modified.
User Manual
Navigation Buttons
Moves menu cursor down. Short hold jumps down one position, long hold
jumps to end of list (Exit).
Moves menu cursor up. Short hold jumps up one position, long hold jumps to
top of list.
Selects menu item at cursor position.
Cursor Function display
Menu point has no sub menu.
Menu point contains a sub menu or an item that may be modifi ed.
Navigation Buttons and Functionality
Press to move the cursor down one level.
Hold down to jump to the final level. (Exit)
Press to move the cursor up one level.
Hold down to jump up to the top of the list.
Select the chosen menu item.
or
<Active DTCs >
ODO: 127mi
Load Rear: 58420lb
Inst. Test Missing
DISCLAIMER
For information
only! Press any key
to continue.
SUPPLY: 11.9V 58368LB
ODO: 127MI
Bendix TIM
™
TABS-6
™
Advanced ABS
Inst. Test Missing
TPMS Info
Main Menu
Exit
or
or or
or
DISCLAIMER
For information
only! Press any key
to continue
<Active DTCs >
ODO: 127mi
Main Menu
Exit
or
or or
or or
BATTERY MODE
For information
only! Values are
read from memory!
Initial Menu
Initial Menu
Initial Menu
Main Menu
Stored DTCs
Distance & Serv.
Operating Info
ECU Info
Main Menu
+
Stored DTCs
Distance & Serv.
Operating Info
System Info
Scroll until
“Main Menu”
Scroll until “Main Menu”
TPMS symbol
(where used)
Bendix TIM
™
TABS-6
™
Advanced ABS
DISPLAYS
With the ignition “ON”
The display is automatically activated. All menus are
available.
With the ignition “OFF”
The display is off, push any navigation button for one second to
activate the display. Only limited menus are available.
SAFE MAINTENANCE PRACTICES
WARNING! PLEASE READ AND FOLLOW
THESE INSTRUCTIONS TO AVOID PERSONAL
INJURY OR DEATH:
When working on or around a vehicle, the following general precautions
should be observed at all times:
1. Park the vehicle on a level surface, apply the parking brakes, and
always block the wheels. Always wear safety glasses. Where
specically directed, the parking brakes may have to be released,
and/or spring brakes caged, and this will require that the vehicle be
prevented from moving by other means for the duration of these tests/
procedures.
2. Stop the engine and remove ignition key when working under or
around the vehicle. When working in the engine compartment, the
engine should be shut off and the ignition key should be removed.
Where circumstances require that the engine be in operation,
EXTREME CAUTION should be used to prevent personal injury
resulting from contact with moving, rotating, leaking, heated or
electrically charged components.
3. Do not attempt to install, remove, disassemble or assemble a
component until you have read and thoroughly understand the
recommended procedures. Use only the proper tools and observe
all precautions pertaining to use of those tools.
4. If the work is being performed on the vehicle’s air brake system,
or any auxiliary pressurized air systems, make certain to drain the
air pressure from all reservoirs before beginning ANY work on the
vehicle. If the vehicle is equipped with a Bendix
®
AD‑IS
®
air dryer
system or a dryer reservoir module, be sure to drain the purge
reservoir.
5. Following the vehicle manufacturer’s recommended procedures,
deactivate the electrical system in a manner that safely removes all
electrical power from the vehicle.
6. Never exceed manufacturer’s recommended pressures.
7. Never connect or disconnect a hose or line containing pressure; it
may whip. Never remove a component or plug unless you are certain
all system pressure has been depleted.
8. Use only genuine Bendix
®
brand replacement parts, components
and kits. Replacement hardware, tubing, hose, ttings, etc. must
be of equivalent size, type and strength as original equipment and
be designed specically for such applications and systems.
9. Components with stripped threads or damaged parts should be
replaced rather than repaired. Do not attempt repairs requiring
machining or welding unless specically stated and approved by the
vehicle and component manufacturer.
10. Prior to returning the vehicle to service, make certain all components
and systems are restored to their proper operating condition.
11. For vehicles with Automatic Traction Control (ATC), the ATC function
must be disabled (ATC indicator lamp should be ON) prior to
performing any vehicle maintenance where one or more wheels on
a drive axle are lifted off the ground and moving.
Initial Menu Main Menu
MENU OVERVIEW
Set Next Service
Date Based
Distance Based
Exit
Info Total
ABS Events
RSP Interventions
Brake History
System Powering
Exit
Info Period
Period mi:
ABS Events:
RSP Interventions
Brake History
System Powering
Reset Period Data
Exit
Set LCD Contrast
LCD Contrast:
Save & Exit
Exit
Manufacturing Info
Part num:
K001966XXXXXX
SW:
Serial:
ManufDate:
Exit
<Active DTCs >
1
ODO: 0mi
Load Rear: lb
Inst. Test Missing
2
TPMS Info
3
Main Menu
Exit
Stored DTCs
Distance & Serv.
System Config
Operating Info
System Info
ECU Info
TIM Info
Exit
Stored
DTCs
Active DTCs:
<none>
Inactive
DTCs:
<none>
Clear DTCs
Exit
Distance & Serv.
ODO: mi
Trip: mi
Reset Trip
Srv Date:
Srv mi:
Set Next Service
Exit
Operating Info
Info Total
Info Period
Exit
ECU Info
Part num:
SW:
Exit
System Info
TPMS Setup
3
Load Info
Pressure Info
Tilt Angle:
Wheel Speeds
Air Gap Speeds
TIM Info
Lang.:
Set LCD Contrast
Manufacturing Info
Exit
+
Repeat until
“Main Menu”
<Active DTCs >
ODO: Omi
Load Rear: lb
Inst. Test Missing
Trailer Information Module
Stored DTCs
Distance & Serv.
Operating Info
System Info
Trailer Information Module
System Config.
ABS Config.:
ECU Orient.:
RSP:
Exit
Installation Test
Exit
Language
English (US)
N.Am. French
N.Am. Spanish
Exit
Date Based
Year:
Month:
Day:
Save & Exit
Exit
Distance Based
Srv mi:
Save & Exit
Exit
RSP Intervention
Test Puls:
Step 1:
Step 2:
Step 3:
Exit
Brake History
Appl vs Dem Values
Over Pressures
Exit
System Powering
ConstPower:
Stop Lamp:
Exit
Load Info
Front Axle Group
4
Bogie Load:
4
Rear Axle Group
Exit
Over Pressures
Dem >130psi:
Res >130psi:
Exit
Appl vs Dem Values
<22psi:
22-36psi:
36-58psi:
>58psi:
Exit
Pressure Info
Dem P4:
Dem CAN:
Susp P42:
Pcyl P21:
Pcyl P22:
Res P1:
Exit
Installation Test
Start Inst. Test
Install Check
Reserv. Press
S-A Sensor:
4
S-E Sensor:
4
S-C Sensor:
S-D Sensor:
S-F Sensor:
4
S-B Sensor:
4
Demand Press:
Tilt Angle:
Exit
TPMS Setup
3
Enter conf. Mode
6
Learn Sensor
5
Delete Sensor
5
Vehicle param.
5
Axle param.
5
Altitude comp:
5
Change password
5
Leave conf. Mode
5
Exit
Enter conf. Mode
6
Password:
Match password
Exit
Vehicle param.
5
FAL% CIP:
SAL % CIP:
Over Temp:
Exit
Change password
5
Password:
New passw.:
Save new passw.
Exit
Menu choices in green are not available in BATTERY MODE
1
Displayed only if active faults are available
2
Displayed only if installation test is missing
3
Displayed onlyifTirePressure Monitoring System (TPMS) is configured
4
Displayed only if included by vehicle ABS configuration
5
Displayed onlyif TPMS configuration mode entered
6
Displayed onlyif TPMS configuration mode not entered
Wheel Speeds
S-A Sensor:
4
S-E Sensor:
4
S-C Sensor:
S-D Sensor:
S-F Sensor:
4
S-B Sensor:
4
Exit
Airgap Speeds
S-A Sensor:
4
S-E Sensor:
4
S-C Sensor:
S-D Sensor:
S-F Sensor:
4
S-B Sensor:
4
Exit
BW2867 © 2011 Bendix Commercial Vehicle Systems LLC, a member of the Knorr‑Bremse Group. 10/11. All Rights Reserved.
EXAMPLES
d) Installation test
Confirm that the
Trailer‘s parking
brake is NOT active
then press ENTER.
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
Confirm that wheel
speed sensors have
been set, then
press ENTER.
= Confirm
Confirm that the
Truck‘s parking
brake is applied
then press ENTER.
= Confirm
= Confirm
(if reservoir pressure > 6Bar)
2x
2x
Install. Check:
Reserv. Press:
S-C Sensor:
S-D Sensor:
Reserv. Press:
S-C Sensor:
S-D Sensor:
Demand Press:
S-C Sensor:
S-D Sensor:
Demand Press:
Tilt Angle:
< 5
o
Installation test
has been success-
fully executed.
Please switch igni-
fully executed.
Please switch igni-
tion OFF-ON to
memorize status.
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
2x
END
Accelerate selected
wheel to 3mph
Fully apply the brake
pedal, then release it
TEBS mounting angle
within tolorance
Confirm that
cables are securely
clipped, then
press ENTER.
= Confirm
Overview of wheel
location, “Confirm”
Overview of wheel
location, “Confirm”
Accelerate selected
wheel to 3mph
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
<Active DTCs>
ODO: 127mi
Load Rear: 58420lb
Inst. Test Missing
Initial Menu
Scroll to “Inst. Test Missing”
+
SECURE Trailer
against movement!
During this test
all its brakes may
all its brakes may
be released auto-
matically! Press
ENTER to confirm
matically! Press
ENTER to confirm
you have secured
the Trailer.
= Confirm
Confirm that all
non connected
ports are plugged
then press ENTER.
= Confirm
Confirm that pneu-
matic connections
are secure, then
press ENTER.
= Confirm
2x
3x
Scroll and follow
instructions on the
screen
Installation test
is missing! To
start it browse to:
Main Menu->
b) Display current Diagnostic
Trouble Code (DTC) status
c) Changing the language
default
a) Setting next service distance to
6,250 miles (mi)
Reset Trip
Srv Date 18-01-10
Srv Mi: 6240mi
Set Next Service
Active DTCs:
S-C O/C.
S-D O/C.
Module Error
Main Menu
Stored DTCs
Distance & Serv.
Operating Info
System Info
+
1x
Date Based
Distance Based
Exit
Srv Mi: 0mi
Save & Exit
Exit
+
5x
+
1x
Srv Mi: 6250mi
Save & Exit
Exit
NOTE: “
*
”
inactive, buttons and
revert to normal function
+
1x
Next service
distance has been
succesfully set in
ECU.
Indicates cursor buttons and
are now used to change ‘mi’ values
“
*
”
Srv Mi:
*
0mi
Save & Exit
Exit
2x
= 6250 mi
+
END
Main Menu
Stored DTCs:
Distance & Serv.
Operating Info
System Info
Overview of DTC
S-C Open circuit or
Shorted to Battery
DTC:
000D00
+
1x
DTC Detail
Scroll
Occurrence count:
4
First detection:
0mi
Scroll
Main Menu
System Info
ECU Info
TIM Info
Exit
+
Scroll to “TIM Info”
Lang.: US English
Scr Saver: Load
Set LCD Contrast
Manufacturing Info
US English
N.Am. French
N.Am. Spanish
Exit
+
1x
Langue: N.Am. French
Eco ecran Charger
Régl Contraste LCD
Info Fabricant
Info Fabricant
Test Affichage
Test Touche
Sortie
Scroll to “Sortie” (Exit)
END
2008-03-15 19:43.44
Last detection:
0mi
2008-03-31 10:11.47
END
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Autel Intelligent Tech. Corp. MX808TS User manual
-
VDO CONTISYS OBD - V3.0 User manual
-
Autel MaxiCOM MK808 User manual
-
Autel MaxiPRO MP808TS User manual
-
Foxwell FOXWELL NT510 Elite Automotive Code Reader for VAG Full Systems Diagnostic Scanner on VW Audi Seat Skoda OBD2 Car Scan Tool All Functions Reset ABS SRS SAS EPB TPMS Oil Light User manual
-
-
MaxiCheck MX808 User manual
-
-
-
LAUNCH LAUNCH AIDIAGSYS TPMS Programming, TPMS Relearn, Sensor Activation, Tire Pressure Monitor Sensor TPMS Reset Tool, Full System Diagnostic OBD2 Scanner User guide
