Vixen Horns VXH2112MAR Owner's manual

Vixen Horns
Brand
Vixen Horns
Model
VXH2112MAR
Type
Owner's manual

This manual is also suitable for

Vixen Horns VXH2112MAR is a dual trumpet marine grade stainless steel horn with a chrome color. It requires a 12-volt DC power source and professional installation is recommended. The horn features a specific voltage requirement of 12 volts DC, and installation must be done to a DC power source of 12 volts. The horn should be set up for use only in areas with adequate ventilation. The horn's wire should be run through the mounting area, and a 10A inline fuse (not provided) should be used to connect the positive wires from each trumpet to the 12-volt positive power source of the vehicle.

Vixen Horns VXH2112MAR is a dual trumpet marine grade stainless steel horn with a chrome color. It requires a 12-volt DC power source and professional installation is recommended. The horn features a specific voltage requirement of 12 volts DC, and installation must be done to a DC power source of 12 volts. The horn should be set up for use only in areas with adequate ventilation. The horn's wire should be run through the mounting area, and a 10A inline fuse (not provided) should be used to connect the positive wires from each trumpet to the 12-volt positive power source of the vehicle.

VXH2112MAR
INSTALLATION GUIDE
PAGE 1 of 2
BEFORE BEGINNING YOUR INSTALLATION
Read through the instruction guide before getting started with the installation. Professional installation is recommended for
this product.
CONTENTS
Dual Trumpet Marine Grade Stainless Steel Horn (Chrome Color)
Mounting Hardware
SAFETY INSTRUCTIONS
Avoid dismantling this horn’s electrical elements.
Avoid setting up any parts of the horn where there is a risk of falling off or risk of coming in contact with water.
Avoid reaching out to touch or pick up any fallen or water submerged parts.
Set the horn up for use only in areas with adequate ventilation.
Avoid sounding the air horn when in close range to your ear(s) or the ear(s) of others.
Make sure your battery ground is detached before getting your installation started.
Employ equipment for eye protection during drilling operations.
The specific voltage requirement for this horn is 12 volt DC, therefore installation must be done to a DC power
source of 12 volts.
MOUNTING
Once you have found a clear space to attach the horn, mark the holes using the provided horn mount and
bracket. Ensure the bracket is moved forward so it is tight, then drill the holes.
If the horn wire is to be run through the mounting area, mark and drill the wire holes.
NOTE: Be careful to avoid sharp ends which could damage the horn’s wire. Using silicon or waterproof
sealant on the wire (by its passage point) is suggested if you are attaching to the roof.
Attach the horn with the included hardware. Screws should be uniformly tightened.
NOTE: To prevent exposure to water, always use the rubber gaskets which are included.
VXH2112MAR
INSTALLATION GUIDE
PAGE 2 of 2
ELECTRICAL CONNECTIONS (OPTIONAL HORN BUTTON)
Using a 10A inline fuse (not provided), connect together both positive wires (RED) from each trumpet and
attach it to the (+) 12-volt positive power source of your vehicle.
Connect together both negative wires (BLACK) from each trumpet and attach it to one of the terminals of the
horn button.
The remaining horn button's terminal should be attach to ground (clean metal surface).
ELECTRICAL CONNECTIONS (FACTORY HORN BUTTON)
TWO WIRE CONNECTION
Remove the wires from your factory horn and
attach each wire to one of the horns.
ONE WIRE CONNECTION
Detach the wire from your factory horn and
attach it to one wire from each of the two horns.
The second wire from each of the horns should
be attached to the ground (clean metal surface).
  • Page 1 1
  • Page 2 2

Vixen Horns VXH2112MAR Owner's manual

Vixen Horns
Brand
Vixen Horns
Model
VXH2112MAR
Type
Owner's manual
This manual is also suitable for

Vixen Horns VXH2112MAR is a dual trumpet marine grade stainless steel horn with a chrome color. It requires a 12-volt DC power source and professional installation is recommended. The horn features a specific voltage requirement of 12 volts DC, and installation must be done to a DC power source of 12 volts. The horn should be set up for use only in areas with adequate ventilation. The horn's wire should be run through the mounting area, and a 10A inline fuse (not provided) should be used to connect the positive wires from each trumpet to the 12-volt positive power source of the vehicle.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents