SKEETER ENTERPRISES V1 Operating instructions

Brand
SKEETER ENTERPRISES
Model
V1
Type
Operating instructions

SKEETER ENTERPRISES V1 is a portable, easy-to-use device with accurate infrared (IR) LIDAR distance data collection and measurement capabilities. Its wireless Bluetooth connectivity allows you to seamlessly transfer data to your smartphone and visualize it within a dedicated app. Whether you're a professional in construction, engineering, or a DIY enthusiast, SKEETER V1 is your go-to tool for precise distance measurements and data analysis. Unleash your creativity and explore endless possibilities for measuring, mapping, and modeling with SKEETER V1.

SKEETER ENTERPRISES V1 is a portable, easy-to-use device with accurate infrared (IR) LIDAR distance data collection and measurement capabilities. Its wireless Bluetooth connectivity allows you to seamlessly transfer data to your smartphone and visualize it within a dedicated app. Whether you're a professional in construction, engineering, or a DIY enthusiast, SKEETER V1 is your go-to tool for precise distance measurements and data analysis. Unleash your creativity and explore endless possibilities for measuring, mapping, and modeling with SKEETER V1.

Stadia Operation
The Stadia device uses an infrared (IR) LIDAR to collect distance data. This distance data is
sent via Bluetooth to the user’s smartphone and interpreted within a purpose-built app.
The Stadia device consists of 4 main parts: LIDAR, Li-ion batteries, microcontroller with
Bluetooth, and an on/off switch.
When the switch is flipped up to the “On” position, LEDs on the Microcontroller will light up.
The device is programmed so that as soon as it is powered, both the Bluetooth and the IR LIDAR
will immediately begin radiating energy in their respective wavelengths.
The Microcontroller is based on the Espressif ESP32 circuit board. The LIDAR is based on the
Garmin LIDAR Lite V3. After the device is switched “Off”, the device will not power back on
for 30 seconds, regardless of the switch position (this is a quirk of the Microcontroller software).
To turn the device back on, leave the switch in the “Off” position for at least 30 seconds, and
then switch it to the “On” position.
Recharging the device is done through a micro-USB cord via the microcontroller. Battery power
is indicated via 4 LEDs on the microcontroller, with the battery percentage labeled next to each
LED (25%, 50%, 75%, 100% [green])
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.
  • Page 1 1
  • Page 2 2

SKEETER ENTERPRISES V1 Operating instructions

Brand
SKEETER ENTERPRISES
Model
V1
Type
Operating instructions

SKEETER ENTERPRISES V1 is a portable, easy-to-use device with accurate infrared (IR) LIDAR distance data collection and measurement capabilities. Its wireless Bluetooth connectivity allows you to seamlessly transfer data to your smartphone and visualize it within a dedicated app. Whether you're a professional in construction, engineering, or a DIY enthusiast, SKEETER V1 is your go-to tool for precise distance measurements and data analysis. Unleash your creativity and explore endless possibilities for measuring, mapping, and modeling with SKEETER V1.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents