WB1520D1
Safety & Operating Manual
Solid Wood Bench
WB1520D1
TABLE OF CONTENTS
Welcome to Lumberjack!
Dear Customer, Congratulations on your purchase.
Before using the product for the first time please be sure to read these instructions
for use.
They provide you with all information necessary for using the product safely and to
ensure its long service life.
Closely observe all safety information in these instructions!
General Tool Safety Warnings
&
Specification................................. 01
Parts List..... ........ ...... ..... ..... ............ ........ .............................................02
-
03
Assembly
I
nstructions .....................................................................0
4
-
0
6
Forestry
C
ertification............................................................................. 0
7
WB1520D1
GENERAL TOOL SAFETY WARNINGS
&
S
P
E
C
IFI
C
ATION
WARNING
:
Read all safety warnings and
all instructions. Failure to follow the warnings
and instructions may result in serious injury.
Save all warnings and instructions for
future reference.
a) Do not exceed weight capacities for the
Workbench shelves and drawers. Be aware of
dynamic loading! Sudden load movement may
briefly create excess load causing product
failure.
b) Use only on flat, level and hard surfaces
capable of supporting the Workbench and any
item(s) placed on Workbench. Evenly distribute
load on Table to avoid tipping.
c) Use as intended only. Do not use Workbench
to perform task for which it was not designed.
d) For indoor use only.
e) Assemble only according to these instructions.
Improper assembly can create hazards.
f) Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly and
use.
g) Keep assembly area clean and well lit.
h) Keep bystanders out of the area during
assembly.
i) Do not assemble when tired or when under
the influence of drugs or medication.
j) This product is not a toy. Do not allow children
to play with, on or near Workbench.
k) Inspect before every use; do not use if parts
are loose or damaged.
Specifications:
Vice Capacity: 7" Inch
Top Shelf Weight Capacity: 113kg
Drawer Weight Capacity: 11kg
Bottom Shelf Capacity: 90kg
Dimensions (Including Vice):
L)1520mm x W) 620mm x H) 850mm
Drawer Inside Dimensions (x4):
L) 325mm x W) 320mm x H) 70mm
WB1520D1 01
Parts List
Part No Description Qty
WB1520D1
1 Side Legs 2
2 Lower Support Brackets 2
3 Bottom Shelf 1
4 Table Top 1
5 Drawer Back 1
6 Drawer Side 2
7 Drawer Front 1
8 Upper Support Brackets 2
9 Drawer Bottom 1
10 Vice 2
11 Wooden Dogs 4
12 Metal Dogs 4
You will also need a cross head
screwdriver & 13mm spanner to build
this bench
WB1520D1
Fixings
Part No Description Qty
A Allen Key 1
B Dowel Nuts 4
C Long Bolts 4
C1 Washers 8
D Blue Long Screws 4
E Heavy Duty Screws 4
F Blue Small Screws 10
03
Stage 1 Assembly of work bench frame.
Parts required for this section: A) x1, B)
x4, C) x4, C1) x4, 1) x2, 2) x2 & 3) x1
Place the washer (C1) over bolt (C) and
insert through the side leg (1) to attach the
lower support bracket (2). Place the dowel
nut into the pre cut hole on the support
bracket (2) and tighten using the allen key (A)
Insert bottom shelf (3) by sliding into the
recess of the support bracket (2). Then
attach the second support bracket (2) to the
side legs (1) using bolt (C), washer (C1) &
dowel nut (B)
Repeat this process again for the second
side leg (1) for the bench to then look like
the below image.
Congratulations stage one is now complete.
Your bench should now look like the image
below.
WB1520D1
04
WB1520D1
Stage 2 Attaching the Table top.
Parts required for this section: D) x4, 4)
x1, 8) x2, 10) x1 C1) x4 & E) x4
(You will also require a cross headed screwdriver
& a 13mm spanner)
Attach upper support brackets (8) to the
table top (4) using screws (D)
Attach the table top (4), using
screws (E) & washers (C1). Insert the
screws from underneath the table top
(4)to secure the bench frame.
Once you have secured the table top (4)
with all four screws (E) & washers (C1)
Your bench should then look like the image
below.
Finally, attach the vice (10) to the front of
the table top (4) into the pre drilled holes
on the left.
Congratulations stage two is now complete.
Your bench should now look like the image
below.
05
Stage 3 Assembly of the drawers.
Parts required for this section: 7) x1,
6) x2, 5) x1, 9) x1 & F) x8
(You will also require a cross headed screwdriver)
To assemble the drawer take both sides (6)
& back (5). Screw together using screws (F)
WB1520D1
Congratulations stage three is now
complete. Your bench is now ready to use.
Once you have screwed the back (5) to
the sides (6) your drawer should look like
this below.
Next take the drawer bottom (9) and slide
into the recess of the sides (6)
Last to do is add the front (7) and secure
tight with screws (F) Then slide the
completed drawer into the recess of the
upper support brackets (8) on the
woodbench.
We wish you many years of enjoyment with your new bench.
06
/
