UKISHIRO DG0JI220824028 User manual











































IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions

should always be followed, including the following

DANGER READ AND FOLLOW ALL

INSTRUCTIONS BEFORE

USING THIS MIRROR

GROUNDING INSTRUCTIONS:

PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

WARNING

To reduce the risk of burns, fire, electric shock or injury to

persons. Use this furnishing only for its intended use as

described in these instructions. Do not use attachments not

recommended by the manufacturer. Never drop o insert any

object into any opening. Do not use outdoors.

This product must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the product.

An Electrical option cabinet must be wired to a 20 Amp GFI

(Ground Fault Interrupter) protected circuit when used in

bathrooms and all other locations required by the National

Electric Code.

Risk of electric shock. Connect this

furnishing to a properly grounded

circuit only. See Grounding instructions.

LED CABINET INSTALLATION GUIDE

TOOLS REQUIRED FOR ASSEMBLY

PARTS INCLUDED

Electrical Drill 1/8” Drill Bit Pencil

Phillips

Screwdriver Tape Measure

NOTE: Determine overall mirror dimensions before

proceeding to installation.

*All dimensions & specifications are approximate and subject to change

without notice.

Level

SCREW

(x7)

WALL PLUG

(x7)

(x12)

(x8)

(x2)

(x3) (x1) (x2) (x6)

LED CABINET INSTALLATION GUIDE

ELECTRIC CONNECTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN

WARNING: Shut off power before wiring the mirror.

WARNING: An Electrical option mirror must be wired to a 20 Amp GFl

(Ground Fault Interrupter) protected circuit when used in bathrooms and

all other locations required by the National Electric Code.

WARNING: This mirror must be connected to a grounded, metal

permanent wiring system or an equipment-grounding conductor must be

run with the circuit conductors and connected to the equipment grounding

terminal or lead on the mirror.

CAUTION: Requires 120 VAC 20 Amp GFI protected circuit.

Live / Black

Field Wire

Ground / Green

Neutral / White

Neutral to white

Live to black

Ground to green.

Make connections

*Wire terminal plate is not included.

MIRROR FEATURES

• 5mm copper free silver mirror

• High output LED lighting:

CRI 90+, 2700-6500K CCT, IP44

• Color Temperature changing touch switch

for surface LED

• Defogger

Electric wiring: Be sure to provide enough

wire to make the proper and safe

connection to the Field/Power.

LED CABINET INSTALLATION GUIDE

 

 

WALL HUNG INSTALLATION

PLACEMENT

Select the desired position of the cabinet.

Level and mark the location.

SUPPORT LOCATION

Measure the center of the holes and mark the

drilling locations ensure marking are leveled.

INSTALL SCREWS

screw and the wall.

Using the two provided screws, install the bracket

onto the bottom of the cabinet.

Hang the cabinet on the cleats and check level,

adjust horizontally to desired location. (This may

require two people)

Lift and remove the cabinet from the wall to reveal

the pencil mark location of the bracket.

Uninstall the bracket from the mirror by removing

the two screws previously installed during step 4.

Mark the location of the bottom bracket on the

wall with a pencil.

 

 

WALL HUNG INSTALLATION

Using the screw provided, mount the bracket to

the wall at the marked pencil location.

Do not over-tighten

Using screws provided, align lower bracket and

attach to cabinet.

Install side mirror.

Lift cabinet and carefully lower onto cleats and

adjust horizontally.

 

 

WALL HUNG INSTALLATION

Install clamps to hold the glass shelf, and install

the shelf.

Secure the position of the glass shelf.

 



WALL HUNG INSTALLATION

1.Move door away/towards

the cabinet.

This must be adjusted

first to prevent scratching

the surface of the

aluminum cabinet.

2.Move door(s) up/down

3.Move door(s) left/right

 

 

 

RECESS INSTALLATION

Draw the dimension of the cabinet on the wall.Measure the size of the cabinet mouted inside

the wall.

Dig out the mounting holes for installation of the

mirror cabinet.

Cut the marked dimension with suitable tool.

Frame the opening for the cabinet based on the

measurements.

Connect electrical wires before inserting the

cabinet into the opening.

3.8” mininum

 

 



RECESS INSTALLATION

Be careful to avoid

squeezing the wiring

while insert the

cabinet.

1.Move door away/towards

the cabinet.

This must be adjusted

first to prevent scratching

the surface of the

aluminum cabinet.

2.Move door(s) up/down

3.Move door(s) left/right

Position cabinet in cut out opening. Affix using hardware screws into the studs.

Install clamps to hold the glass shelf, and install

the shelf.

Secure the position of the glass shelf.

FINAL ASSEMBLY

Touch to turn the task light and defogger on or off.

Press and hold to change the color temperature of the task light.

Single button touch switch

Touch to turn the task light on or off.

Touch to turn the defogger on or off.

Press and hold to change the color temperature of the task light.

Press and hold to dim or brighten the task light.

Double buttons touch switch

Touch to turn the task light on or off.

Touch to cycle color temperature.

Touch to turn the defogger on or off.

3 buttons touch switch

Press and hold to dim or brighten the task light.

Press and hold to change the color temperature of the task light.

UKISHIRO DG0JI220824028, DG0JI220824029 User manual

Other documents