Gigabyte C621-WD12 Owner's manual

GA-C621-WD12(-IPMI)

User's Manual

Rev. 1001

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form

or by any means without GIGABYTE's prior written permission.

For product-related information, check on our website at: https://www.gigabyte.com

- 4 -

Table of Contents

GA-C621-WD12 Motherboard Layout .............................................................................5

Box Contents ...................................................................................................................6

Chapter 1 Hardware Installation .....................................................................................7

1-1 Installation Precautions .................................................................................... 7

1-2 Product Specications ...................................................................................... 8

1-3 Installing the CPU .......................................................................................... 10

1-4 Installing the Memory ..................................................................................... 11

1-5 Back Panel Connectors .................................................................................. 12

1-6 Internal Connectors ........................................................................................ 14

Chapter 2 BIOS Setup ..................................................................................................24

2-1 Startup Screen ............................................................................................... 24

2-2 Main ............................................................................................................... 25

2-3 Advanced ....................................................................................................... 26

2-4 Platform Conguration ................................................................................... 29

2-5 Socket Conguration ...................................................................................... 31

2-6 Server Mgmt ................................................................................................... 33

2-7 Security .......................................................................................................... 34

2-8 Boot ................................................................................................................ 35

2-9 Save & Exit ..................................................................................................... 36

Chapter 3 Application....................................................................................................37

Regulatory Statements .............................................................................................. 46

Contact Us ................................................................................................................ 47

- 5 -

GA-C621-WD12 Motherboard Layout

1 BMC_VGA *

2BMC_WATCHD *

3 COM

4 SMB_IPMB *

5 I_SGPIO1

6 I_SGPIO2

7 WOL

8 SMB

9 TPM

10 TBT

11 BMC_UART *

12 SATA_DOM0

13 SATA_DOM1

14 VRM_SCL

15 VRM_SDA

16 FUSB30

17 VROC

18 FUSB2

19 F_PANEL

20 PMBUS

21 CLR_CMOS

22 CI

23 CPU_FAN1~2

24 SYS_FAN1~5

25 ATX

26 ATX8P_1~2

27 ATX12V 6P

28 S-SATA0~1

29 I-SATA0~7

30 PCIEX4_M2

31 U2_1~2

32 PWR_SW

33 RST_SW

34 S_SGPIO

35 F_AUDIO

36 VGA *

37 SMB_VMD

38 SPEAKER

39 BMC_LED2 *

40 BAT

1

20

24

39 235

4

5

6

7

10

14

16

18

17

15

19

25

12

9

13

23

22

11

8

33 27

26

3

32 21

30

29

38

31

34

36

23

24

26

37

40

28

* Only for the GA-C621-WD12-IPMI.

- 6 -

Box Contents

5GA-C621-WD12 or GA-C621-WD12-IPMI motherboard

5Motherboard driver disk 5I/O Shield

5Quick Installation Guide 5One VGA bracket *

5Ten SATA cables 5One COM port bracket *

* Only for the GA-C621-WD12-IPMI.

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,

keep your hands dry and rst touch a metal object to eliminate static electricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Do not place the computer system on an uneven surface.

•Do not place the computer system in a high-temperature or wet environment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 7 -

1-2 ProductSpecications

CPU Support for Intel® Xeon® Scalable Processors in the LGA 3647 package

 Dual Socket P (Square) with 2 UPI support of up to 10.4 GT/s, CPU TDP support

up to 205W

Chipset Intel® C621 Chipset

Memory 12 x DDR4 DIMM sockets supporting up to 1.5 TB of system memory

6 channel memory architecture (6 channel per CPU)

Support for DDR4 2666 MHz memory modules if use a Skylake CPU

Support for DDR4 2933 MHz memory modules if use a Cascade lake CPU

Support for ECC RDIMM/RDIMM 3DS/LRDIMM/LRDIMM 3DS memory modules

Audio Realtek® ALC1220-VB codec

High Denition Audio

2/4/5.1/7.1-channel

Support for S/PDIF Out

LAN 2 x Intel® 210AT GbE LAN chips (10/100/1000 Mbit)

Expansion Slots 4 x PCI Express x16 slots, running at x16

3 x PCI Express x16 slots, running at x8

(All of the PCI Express x16 slots conform to PCI Express 3.0 standard.)

Storage Interface Chipset:

- 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 SATA and

PCIe x4/x2 SSD support)

- 8 x SATA 6Gb/s connectors (I-SATA0~I-SATA7)

- 2 x SATA 6Gb/s connectors (S-SATA0, S-SATA1)

- 2 x U.2 connectors

- Support for RAID 0, RAID 1, RAID 5, and RAID 10

USB Chipset:

- 1 x USB Type-C™ port on the back panel, with USB 3.1 Gen 2 support

- 1 x USB 3.1 Gen 2 Type-A ports (red) on the back panel

- 7 x USB 3.1 Gen 1 ports (4 ports on the back panel, 1 port onboard, 2 ports

available through the internal USB header)

- 2 x USB 2.0/1.1 ports available through the internal USB header

Internal

Connectors

1 x 24-pin ATX main power connector

2 x 8-pin ATX 12V power connectors

1 x 6-pin ATX 12V power connector

2 x CPU fan headers

5 x system fan headers

1 x M.2 Socket 3 connector

10 x SATA 6Gb/s connectors

2 x U.2 connectors

2 x SATA DOM power headers

1 x PMBus connector

1 x Intel® VROC Upgrade Key header

1 x front panel header

1 x front panel audio header

1 x USB 3.1 Gen 1 header

1 x USB 3.1 Gen 1 port

- 8 -

Internal

Connectors

1 x USB 2.0/1.1 header

1 x Trusted Platform Module (TPM) header

1 x serial port connector

1 x chassis intrusion header

3 x SATA SGPIO headers

1 x SMD_VMD header

1 x IPMB connector *

1 x SMB connector

1 x TBT connector

1 x BMC_UART connector *

1 x VGA connector *

1 x wake on LAN header

1 x speaker header

1 x Clear CMOS jumper

1 x VGA jumper *

1 x Watch-Dog timer jumper *

1 x VRM SMB Clock jumper

1 x VRM SMB Data jumper

1 x power button

1 x reset button

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

1 x USB Type-C™ port, with USB 3.1 Gen 2 support

1 x USB 3.1 Gen 2 Type-A port (red)

4 x USB 3.1 Gen 1 ports

2 x USB 2.0/1.1 ports

2 x RJ-45 ports

1 x optical S/PDIF Out connector

 5 x audio jacks

I/O Controller ASPEED® AST2500 BMC chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Fan speed control

* Whether the fan speed control function is supported will depend on the fan you install.

BIOS 1 x 256 Mbit ash

Use of licensed AMI BIOS

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

Operating

Properties

Operating temperature: 10°C to 40°C

Operating humidity: 8 - 80%

Non-operating temperature: -40°C to 70°C

Non-operating humidity: 5% - 95%

Form Factor EEB Form Factor; 30.5cm x 33.0cm

* GIGABYTE reserves the right to make any changes to the product specications and product-related information without

prior notice.

- 9 -

* Only for the GA-C621-WD12-IPMI.

1-3 Installing the CPU

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locate the notches on both sides of the CPU and alignment keys on the CPU socket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage

of the CPU may occur.

• Set the CPU host frequency in accordance with the CPU specications. It is not recommended

that the system bus frequency be set beyond hardware specications since it does not meet the

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications, please do so according to your hardware specications including the CPU, graphics

card, memory, hard drive, etc.

- 10 -

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

1

A

B

C

2

3

4

5

7

6

8

Due to CPU limitations, read the following guidelines before installing the memory in 6 Channel mode.

1. 6 Channel mode cannot be enabled if only one memory module is installed.

2. When enabling 6 Channel mode with two memory modules, it is recommended that memory of the same

capacity, brand, speed, and chips be used.

6ChannelMemoryConguration

This motherboard supports 6 Channel Technology. After the memory is installed, the BIOS will automatically

detect the specications and capacity of the memory.

The twelve DDR4 memory sockets are divided into 6 channels and each channel has two memory sockets

as following:

Channel 1: P1-DIMM-A1 (For CPU 1)/P2-DIMM-G1 (For CPU 2)

Channel 2: P1-DIMM-B1 (For CPU 1)/P2-DIMM-H1 (For CPU 2)

Channel 3: P1-DIMM-C1 (For CPU 1)/P2-DIMM-J1 (For CPU 2)

Channel 4: P1-DIMM-D1 (For CPU 1)/P2-DIMM-K1 (For CPU 2)

Channel 5: P1-DIMM-E1 (For CPU 1)/P2-DIMM-L1 (For CPU 2)

Channel 4: P1-DIMM-F1 (For CPU 1)/P2-DIMM-M1 (For CPU 2)

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

- 11 -

1-5 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

USB 3.1 Gen 2 Type-A Port (Red)

The USB 3.1 Gen 2 Type-A port supports the USB 3.1 Gen 2 specication and is compatible to the USB

3.1 Gen 1 and USB 2.0 specication. Use this port for USB devices.

USB Type-C™ Port

The reversible USB port supports the USB 3.1 Gen 2 specication and is compatible to the USB 3.1 Gen

1 and USB 2.0 specication. Use this port for USB devices.

GbE LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describes the states of the LAN port LEDs.

Link LEDActivity LED

LAN Port

LED State Description

Link (Right) Solid Green 100 Mbps data rate

Solid Amber 1 Gbps data rate

Activity (Left) Blinking Yellow Active

USB 3.1 Gen 1 Port

The USB 3.1 Gen 1 port supports the USB 3.1 Gen 1 specication and is compatible to the USB 2.0

specication. Use this port for USB devices.

Center/Subwoofer Speaker Out

Use this audio jack to connect center/subwoofer speakers.

Rear Speaker Out

Use this audio jack to connect rear speakers.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio.

Before using this feature, ensure that your audio system provides an optical digital audio in connector.

Line In/Side Speaker Out

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out/Front Speaker Out

The line out jack. This jack supports audio amplifying function. For better sound quality, it is recommended

that you connect your headphone/speaker to this jack (actual effects may vary by the device being used).

- 12 -

Mic In/Side Speaker Out

The Mic in jack.

•When removing the cable connected to a back panel connector, rst remove the cable from

your device and then remove it from the motherboard.

•When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

•If you want to install a Side Speaker, you need to retask either the Line in or Mic in jack to be

Side Speaker out through the audio driver.

•To enable or congure the audio amplifying function for the Line out jack, please access the

HD Audio Manager application.

Audio Jack Congurations:

Jack Headphone/

2-channel 4-channel 5.1-channel 7.1-channel

Center/Subwoofer Speaker

Out a a

Rear Speaker Out a a a

Line In/Side Speaker Out a

Line Out/Front Speaker Out a a a a

Mic In/Side Speaker Out a

- 13 -

1-6 Internal Connectors

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the

power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has been securely

attached to the connector on the motherboard.

- 14 -

1 BMC_VGA *

2BMC_WATCHD *

3 COM

4 SMB_IPMB*

5 I_SGPIO1

6 I_SGPIO2

7 WOL

8 SMB

9 TPM

10 TBT

11 BMC_UART *

12 SATA_DOM0

13 SATA_DOM1

14 VRM_SCL

15 VRM_SDA

16 FUSB30

17 VROC

18 FUSB2

19 F_PANEL

20 PMBUS

21 CLR_CMOS

22 CI

23 CPU_FAN1~2

24 SYS_FAN1~5

25 ATX

26 ATX8P_1~2

27 ATX12V 6P

28 S-SATA0~1

29 I-SATA0~7

30 PCIEX4_M2

31 U2_1~2

32 PWR_SW

33 RST_SW

34 S_SGPIO

35 F_AUDIO

36 VGA *

37 SMB_VMD

38 SPEAKER

39 BMC_LED2 *

40 BAT

1

20

24

39 235

4

5

6

7

10

14

16

18

17

15

19

25

12

9

13

23

22

11

8

33 27

26

3

32 21

30

29

38

31

34

36

23

24

26

37

40

28

* Only for the GA-C621-WD12-IPMI.

3) COM

Pin Denition Pin Denition

1 NDCD- 2 NSIN

3 NSOUT 4 NDTR-

5 GND 6 NDSR-

7 NRTS- 8 NCTS-

9 NRI- 10 -

9

1

10

2

4) SMB_IPMB *

Pin Denition

1 SMB_DATA

2 GND

3 SMB_CLK

4 NA

1

- 15 -

Pin Denition

1-2 Enable (Default)

2-3 Disable

1

1) BMC_VGA *

Pin Denition

1-2 Enable

2-3 Disable (Default)

1

2) BMC_WATCHD *

* Only for the GA-C621-WD12-IPMI.

Pin Denition Pin Denition

1 NA 2 -

3SATA_DATA 4 GND

5 GND 6 SATA_LOAD

7 NA 8 SATA_CLK

2

8

1

7

5) I_SGPIO1 (For I-SATA0~3)

6) I_SGPIO2 (For I-SATA4~7)

Pin Denition

1 Power (5V)_AUX

2 GND

3 WAKE_EN

1

7) WOL (Wake On Lan)

Pin Denition

1 SMB_DATA

2 GND

3 SMB_CLK

1

8) SMB

Pin Denition Pin Denition

1 LPC_IO0 2 Power (3.3V)

3 LPC_IO1 4 -

5 LPC_IO2 6 TPM_CLK

7 LPC_IO3 8 GND

9 LFRAME# 10 NA

11 SERIRQ 12 TPM_RST

2

12

1

11

9) TPM (Trusted Platform Module/Port 80 Header)

- 16 -

10) TBT

1

5

Pin Denition

1 FORCE_POWER

2 SCI_EVENT

3 SLP_S3

4 SLP_S5

5 GND

Pin Denition

1 BMC_UART_TXD

2 GND

3 BMC_UART_RXD

4 Power (5V)

1

11) BMC_UART *

Pin Denition

1 Power (5V)

2 GND

3 NA

1

12) SATA_DOM0 (SATA DOM0 Power Header)

13) SATA_DOM1 (SATA DOM1 Power Header)

Pin Denition

1-2 SMB to PCH

2-3 SMB to BMC

1

14) VRM_SCL (For VRM SMB_CLK)

15) VRM_SDA (For VRM SMB_DATA)

* Only for the GA-C621-WD12-IPMI.

- 17 -

1

10

20

11

16) FUSB30

Pin Denition Pin Denition

1 VBUS 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 GND

4 GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7 GND 17 SSRX2+

8 D1- 18 SSRX2-

9 D1+ 19 VBUS

10 NC 20 -

Pin Denition

1 GND

2 Power (3.3V)_AUX

3 GND

4 PCH RAID KEY

1

17) VROC (RAID Key for CPU NVMe SSD)

Pin Denition Pin Denition

1 Power (5V) 2 Power (5V)

3 USB DX- 4 USB DY-

5 USB DX+ 6 USB DY+

7 GND 8 GND

9 - 10 NC

9

1

10

2

18) FUSB2

2423

21

19) F_PANEL

Pin Denition Pin Denition

1 Power LED+ 2 5V Standby

3 - 4 ID LED+

5 Power LED- 6 ID LED-

7 HDD LED+ 8 System Status LED+

9 HDD LED1 10 System Status LED-

11 Power Button 12 LAN1 Active LED+

13 GND 14 LAN1 Link LED-

15 Reset Button 16 SMBus Data

17 GND 18 SMBus Clock

19 ID Button 20 Case Open

21 GND 22 LAN2 Active LED+

23 NMI Switch 24 LAN2 Link LED-

- 18 -

Pin Denition

1 SMB_CLK

2 SMB_DATA

3 PSU_ALERT

4 GND

5 Power (3.3V)

1

20) PMBUS (Power supply I2C Connector)

Pin Denition

1-2 NA (Default)

2-3 Clear CMOS

1

21) CLR_CMOS

Pin Denition

1 Intrusion Input

2 GND

1

22) CI

Pin Denition

1 GND

2 Power (12V)

3 FAN_TACH

4 FAN_PWM

1

CPU_FAN2CPU_FAN1

23) CPU_FAN1/CPU_FAN2

- 19 -

Pin Denition

1 GND

2 Power (12V)

3 FAN_TACH

4 FAN_PWM

24) SYS_FAN1~5

1

SYS_FAN2SYS_FAN1~5

25) ATX (2x12 Main Power Connector)

1 13

12 24

26) ATX8P_1~2 (2x4, 12V Power Connectors)

4 8

1 5

27) ATX12V_6P (2x3, 12V Power Connectors)

4 6

1 3

- 20 -

Page is loading ...

Gigabyte C621-WD12 Owner's manual

This manual is also suitable for

Gigabyte C621-WD12 Owner's manual

Related papers

Other documents