NXP TEA179X User guide

Brand: NXP

Model: TEA179X

Type: User guide

This manual is also suitable for

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

Rev. 01 — 28 May 2010 User manual

Document information

Info Content

Keywords GreenChip III, TEA1752T, GreenChip SR, TEA1791T, PFC, flyback,

synchronous rectification, high efficiency, adapter, notebook, PC power

Abstract This manual provides the specification, performance, schematics, bill of

materials and PCB layout of a 90 W notebook adapter using the

TEA1752T and TEA1791T. For design details on the TEA1752T and

TEA1791T please refer to the application notes.

User manual Rev. 01 — 28 May 2010 2 of 32

Contact information

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: [email protected]

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

Revision history

Rev Date Description

01 28 May 2010 First Draft

User manual Rev. 01 — 28 May 2010 3 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

1. Introduction

This manual describes a universal input, 19.5 V, 4.62 A single output power supply using

TEA1752T and TEA1791T devices from the GreenChip-III and GreenChip-SR family of

NXP Semiconductors. It contains the specification of the power supply, circuit diagram,

the component list to build the supply, the PCB layout and component positions,

documentation of the PFC choke and transformer, along with test data and oscilloscope

pictures of the most important waveforms.

The GreenChip-3 combines the control and drive for both the PFC and the flyback stages

into a single device. The TEA1752T: provides complete SMPS control functionality to

comply with the IEC61000-3-2 harmonic current emission requirements, obtain a

significant reduction of components, save PCB space and give a cost benefit. It also offers

extremely low power consumption in no-load mode, which makes it suitable for the

low-power consumer markets. The built-in green functions ensure high efficiency at all

power levels, which results in a design that can easily meet all existing and proposed

energy efficiency standards such as: CoC (Europe), ENERGY STAR (US), CEC

(California), MEPS (Australian and New Zealand), and CECP (China).

The GreenChip SR is a synchronous rectification control IC that needs no external

components to tune the timing. Used in notebook adapter designs, the GreenChip SR

offers a wide VCC operating range between 8.5 V and 38 V, minimizing the number of

external components required and enabling simpler designs. In addition, the high driver

output voltage (10 V) makes the GreenChip SR compatible with all brands of MOSFETs.

WARNING

Lethal voltage and fire ignition hazard

The non-insulated high voltages that are present when operating this product, constitute a

risk of electric shock, personal injury, death and/or ignition of fire.

This product is intended for evaluation purposes only. It shall be operated in a designated test

area by personnel that is qualified according to local requirements and labor laws to work with

non-insulated mains voltages and high-voltage circuits. This product shall never be operated

unattended.

User manual Rev. 01 — 28 May 2010 4 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

2. Specification

• Mains input voltage: 90 V to 264 V; 47 Hz to 63 Hz

• DC output: 19.5 V; ±2 %

• Maximum continuous output current: 4.62 A

• Peak output current: ≥ 5.7 A

• Efficiency: > 88.5 % at maximum load

• ENERGY STAR active mode efficiency: > 89.5 %

• No load power consumption: ≤ 0.2 W

• Dynamic load response (peak-to-peak): 700 mV

• Output ripple and noise (peak-to-peak): 100 mV

• CISPR22 class B conducted EMI (−15 dB margin)

• EN61000-4-2 immunity against ESD (≥ ±12 kV air discharge)

• EN61000-3-2 A14 (harmonics) compliance

• Short Circuit Protection (SCP); input power < 1.2 W during SCP test

• OverCurrent Protection (OCP); input power < 2.2 W during OCP test

• Latched output OverVoltage Protection (OVP): < 24 V

• Latched OverTemperature Protection (OTP); ≤ 120 °C

• Fast Latch Reset (FLR): < 2 s

Fig 1. 90 W TEA1752T and TEA1791T demo board

001aak8

User manual Rev. 01 — 28 May 2010 5 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3. Performance data

3.1 Test setup

3.1.1 Test equipment

• AC source: Agilent 6812B

• Power meter: Yokogawa WT210 with Harmonics option

• DC electronic load: Chroma, Model 63103

• Digital oscilloscope: Yokogawa DL1640L

• Current probe Yokogawa 701933 30A; 50MHz

• 100 MHz, high voltage differential probe: Yokogawa 700924

• 500 MHz, low voltage differential probe: Yokogawa 701920

• Multimeter: Keithley 2000

• EMC receiver: Rohde & Schwarz ESPI-3 + LISN ENV216

3.1.2 Test conditions

• Adapter on the lab-table with the heat sinks downwards

• The adapter has no casing

• Ambient temperature between 20 °C and 25 °C

• Measurements were made after stabilization of temperature according to "test method

for calculating the efficiency of single-voltage external AC-DC and AC-AC power

supplies" of ENERGY STAR

3.2 Efficiency

3.2.1 ENERGY STAR efficiency

To market adapters as ENERGY STAR efficient they have to pass the active mode and

no-load criteria as stated in the ENERGY STAR standard for External Power Supplies;

EPS2.0. The minimum active-mode efficiency is defined as the arithmetic average

efficiency at 25 %, 50 %, 75 % and 100 % of the rated output power as printed on the

nameplate of the adapter.

3.2.1.1 Active mode efficiency

Test Conditions:

The adapter is set to maximum load and well pre-heated until temperature stabilization is

achieved. Temperature stabilization is established for every load step before recording

any measurements.

Remark: The output voltage is measured at the end of the output cable (2 × 20 mΩ).

User manual Rev. 01 — 28 May 2010 6 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

Criteria to pass:

To comply with ENERGY STAR EPS2.0, the arithmetic average of the four efficiency

measurements must be greater than, or equal to, 87 %. Universal mains adapters have to

pass the criteria at both 115 V; 60 Hz and 230 V; 50 Hz. To meet this criteria, the PFC

must be off at 25 % load and preferably on at 50 % load.

3.2.1.2 No-load input power

Test Conditions:

The adapter is set to maximum load and pre-heated. After 5 minutes the load is removed.

The no-load input power measurements were recorded after stabilization of the input

power reading.

Criteria to pass:

To comply with ENERGY STAR EPS2.0, the input power must be less than 0.5 W.

Universal mains adapters have to pass the criteria at both 115 V; 60 Hz and 230 V; 50 Hz.

The adapter is set to maximum load and pre-heated. After 5 minutes the load is removed.

The no-load input power measurements were recorded after stabilization of the input

power reading.

Table 1. Active mode efficiency at 115 V; 60 Hz

Load (%) I

(A) V

(V) P

(W) P

(W) Efficiency

(%)

Power

factor

100 4.628 19.173 88.72 98.94 89.67 0.986

75 3.472 19.246 66.81 73.74 90.61 0.979

50 2.315 19.318 44.73 49.33 90.67 0.965

25 1.160 19.383 22.49 24.69 91.08 0.450

Average - - - - 90.51 -

Table 2. Active mode efficiency at 230 V; 50 Hz

Load (%) I

(A) V

(V) P

(W) P

(W) Efficiency

(%)

Power

factor

100 4.628 19.175 88.73 98.41 90.17 0.945

75 3.472 19.247 66.82 74.31 89.92 0.921

50 2.316 19.319 44.73 50.49 88.60 0.878

25 1.160 19.385 22.49 24.75 90.87 0.378

Average - - - - 89.89 -

Table 3. PFC on and off level as a function of the mains input voltage

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

Output current (A) (PFC on) 1.75 1.83 1.88 1.91 1.86

Output current (A) (PFC off) 1.35 1.36 1.34 1.35 1.31

Table 4. No-load input power

No-load input power as a function of the mains input voltage.

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

Input power P

(W) 0.137 0.139 0.142 0.182 0.200

User manual Rev. 01 — 28 May 2010 7 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.2.1.3 Full load efficiency PFC plus flyback stage

Test conditions:

Before any measurements were recorded, the adapter is set to maximum load and is

preheated till the readings were stabilized.

Remark: The output voltage is measured at the end of the output cable. (2 × 20 mΩ)

Criteria to pass:

The efficiency (η) must be > 88 % at the maximum continuous output load.

3.3 Timing and protection

3.3.1 Switch-on delay and output rise time

Test conditions:

The electronic load is set to Constant Current (CC) mode and V

= 0 V. The electronic

load is set to the maximum continuous output current.

Criteria to pass:

• Switch-on delay: two seconds maximum after the AC mains voltage is applied to the

time when the output is within regulation

• Output rise time: The output voltage must rise from 10 % of the maximum to the

regulation limit within 30 ms. There must be a smooth and continuous ramp-up of the

output voltage. No voltage with a negative polarity must be present at the output

during start-up

• No output bounce or hiccup is allowed during switch-on.

• There be must be sufficient margin between the FBCTRL signal and the 4.5 V

time-out trigger level to avoid false triggering of the time-out protection due to

component tolerances

Table 5. PFC plus flyback stage

Total converter efficiency (at full load) as a function of the mains input

Mains supply V; Hz I

RMS (A) P

(W) P

(W) Efficiency

(%)

Power factor

90; 60 1.130 88.74 100.24 88.53 0.989

100; 50 1.013 88.76 99.58 89.14 0.987

115; 60 0.877 88.72 98.94 89.67 0.986

230; 50 0.456 88.73 98.41 90.17 0.945

264; 50 0.402 88.66 98.26 90.24 0.929

User manual Rev. 01 — 28 May 2010 8 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

a. Mains input 90 V; 60 Hz; delay time 484 ms b. Mains input 264 V; 50 Hz; delay time 484 ms

Load = 4.62 A

CH1: mains input

CH2: VCC pin TEA1752T

CH3:FBCTRL pin TEA1752T

CH4: output voltage

Load = 4.62 A

CH1: mains input

CH2: VCC pin TEA1752T

CH3: FBCTRL pin TEA1752T

CH4: output voltage

Fig 2. Delay between switch-on and output in regulation

019aaa009 019aaa010

a. Mains input 90 V; 60 Hz; output rise time 12.64 ms b. Mains input 264 V; 50 Hz; output rise time

12.24 ms

Load = 4.63 A

CH1: mains input

CH2: FBCTRL pin TEA1752T

CH3: FBSENSE pin TEA1752T (soft start)

CH4: output voltage

Load = 4.63 A

CH1: mains input

CH2: VCC pin TEA1751T

CH3: FBSENSE pin TEA1751T (soft start)

CH4: output voltage

Fig 3. Output rise time at full load start-up

019aaa011

019aaa012

User manual Rev. 01 — 28 May 2010 9 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.3.2 Brownout and brownout recovery

The voltage on the VINSENSE pin is monitored continuously to prevent the PFC from

operating at very low mains input voltages.

Test Conditions:

The mains input voltage is decreased from 90 V down to 0 V and then increased from 0 V

to 90 V. The electronic load is set to Constant Current (CC) mode and V

=0V. The

electronic load is set to the maximum continuous output current.

Criteria to pass:

• The adapter must survive the test without damage and excessive heating of

component

• The output voltage must remain within the specified regulation limits or switch-off

• No output bounce or hiccup is allowed during switch-on or switch-off

• The adapter must power-up before the AC line input voltage reaches 85 V (maximum)

3.3.3 Output short circuit protection

To protect the adapter and application against an output short circuit or a single fault open

(flyback) feedback loop situations, time-out protection is implemented. When the voltage

on FBCTRL pin rises above 4.5 V (typical.), a fault is assumed and switching is blocked.

The time-out protection must not trigger during a normal start-up with the maximum

continuous output current.

a. AC mains input from 90 V to 0 V b. AC mains input from 0 V to 90 V

brownout voltage =

Load = 4.62 A

CH1: mains input

CH2: VINSENSE pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

brownout recovery voltage =

Load = 4.62 A

CH1: mains input

CH2: VINSENSE pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Fig 4. Brownout and brownout recovery

019aaa013 019aaa014

108 2()⁄ 76 V= 121 2()⁄ 86 V)=

User manual Rev. 01 — 28 May 2010 10 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

Test Conditions:

There are two test conditions:

1. The adapter is switched on with 4.62 A output load. After startup a short circuit is

applied manually at the end of the output cable

2. Before the adapter is switched on a short circuit is applied to at the end of the output

cable

Remark: An output short-circuit is defined as an output impedance of less than 0.1 ohm.

Criteria to pass:

• The adapter must be capable of withstanding a continuous short-circuit at the output

without damaging or overstressing the adapter under any input conditions

• The average input power must be less than 3 W during the short-circuit test

• After removal of the short circuit, the adapter must recover automatically

a. Mains input 90 V; 60 Hz b. Mains input 264 V; 50 Hz

Load before short circuit = 4.62 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Load before short circuit = 4.62 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: FBDRIVER pin TEA1752T

CH4: output voltage

Fig 5. Output short-circuit, triggering of the time-out protection

019aaa015

019aaa016

User manual Rev. 01 — 28 May 2010 11 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

a. Output short-circuit during normal operation b. Output short-circuit applied before start-up

Load before short circuit= 4.62 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Load = short circuit

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Fig 6. Output short-circuit at 90 V; 60 Hz

019aaa017

019aaa018

a. Output short-circuit during normal operation b. Output short-circuit applied before start-up

Load before short circuit = 4.62 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Load = short circuit

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Fig 7. Output short-circuit at 264 V; 50 Hz

019aaa019

019aaa020

User manual Rev. 01 — 28 May 2010 12 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.3.4 Output OverCurrent protection (OCP)

Test Conditions:

• The electronic load is set in Constant Current (CC) mode

• The load is increased from the maximum continuous value in small steps until the

over current protection is triggered. The input power is measured after triggering over

the over current protection without changing the load setting

Criteria to pass:

• The output power must be limited to less than 150 W, just before the triggering of the

over current protection

• The average input power must be less than 3 W once the over current protection has

been triggered

3.3.5 Output OverVoltage Protection (OVP)

Test Conditions:

• The adapter is switched on without a load at the output

• An output over-voltage is created by applying a short circuit across the opto LED of

Criteria to pass:

• The output voltage must not exceed 25 V or stabilize between 25 V and the rated

output voltage

• The voltage on the TEA1752T VCC pin must not exceed the absolute maximum rating

of 38 V

• When OVP is triggered, the primary side controller must shut down and stay in a

latched mode

• A single point fault must not cause a sustained overvoltage condition at the output

Table 6. Output short circuit input power

Output short circuit input power as a function of the mains input voltage

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

Input power P

(W) 1.113 1.013 0.877 0.456 0.402

Table 7. Output over current protection and input power as a function of the mains input

voltage.

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

Over current trigger level (A) 6.45 6.47 6.47 6.05 6.05

Input power P

(W) 1.92 1.89 1.82 2.17 2.11

Table 8. Output over-voltage protection

Output over-voltage at no-load as a function of the mains input voltage with protection mode latched

Mains supply (V; Hz) 90; 60 100; 50 115; 60 230; 50 264; 50

Output OVP trip point (V) 23.8 23.8 23.7 23.8 23.7

VCC maximum during

OVP (V)

27.5 27.5 27.5 27.1 27.0

User manual Rev. 01 — 28 May 2010 13 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.3.6 OverTemperature protection (OTP)

An accurate external over temperature protection (TEA1752T’s LATCH pin, RT2, R26 and

C19) is provided on the demo board to protect the flyback transformer against overheating

(see Figure 14

). Normally, the flyback transformer is the most heat sensitive component.

Test Conditions:

The NTC temperature sensor, glued to the transformer, is heated using a heat gun.

Criteria to pass:

The IC must latch off the output at a VLATCH trip level of 1.25V. No output bounce or

hiccup is allowed

a. Mains input 90 V; 60 Hz b. Mains input 264 V; 50 Hz

Load before short circuit = 0 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Load before short circuit = 0 A

CH1: drain flyback MOSFET

CH2: FBCTRL pin TEA1752T

CH3: VCC pin TEA1752T

CH4: output voltage

Fig 8. Output OverVoltage Protection

019aaa021 019aaa022

User manual Rev. 01 — 28 May 2010 14 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.3.7 Fast latch reset

A Fast Latch Reset function (FLR) enables latched protection to be reset without

discharging the bulk elcap. The latch protection is reset as soon as the voltage on

VINSENSE pin drops below 0.75 V and is then raised to 0.87 V.

Test conditions:

• The output is not loaded

• The test sequence is as follows:

– The latch protection is triggered by an OVP caused by a short-circuit across the

OPTO led

– The mains input is switched off and the voltage on pin VINSENSE dropped below

0.75 V

– The mains input is switched on and, as soon as the voltage on pin VINSENSE

rises above 0.87 V, the latch is reset

Remark: Both live and neutral must be switched.

Criteria to pass:

The latch must be reset within 3 seconds after switching off and switching on, the mains

input voltage.

OTP trigger temperature 108 °C

Load before short-circuit = 0 A

CH1: V

out

CH2: TEA1752T VCC pin

CH3: Mains input voltage

CH4: TEA1752T LATCH pin

Fig 9. External OverTemperature Protection (OTP)

001aak80

User manual Rev. 01 — 28 May 2010 15 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.4 Output regulation and characterization

3.4.1 Load regulation

Test conditions:

• The output voltage deviation is measured while the load current on the output is

increased from 0 A to 4.62 A

• The measurement is repeated for different mains input voltages

Remark: The output voltage is measured at the end of the output cable (2 × 20 mΩ).

Criteria to pass:

The output load regulation must remain within 2 %.

The load regulation is calculated using Equation 1

(1)

where V

O(nom)

= 19.5 V.

a. Mains input 90 V; 60 Hz; FLR = 1.6 s b. Mains input 264 V; 50 Hz; FLR = 1.3 s

CH1: V

out

CH2: VCC pin TEA1752T

CH3: AC mains input

CH4: VINSENSE pin TEA1752T

CH1: V

out

CH2: VCC pin TEA1752T

CH3: AC mains input

CH4: VINSENSE pin TEA1752T

Fig 10. Fast Latch Reset (FLR)

001aak80

Table 9. Load regulation

Output voltage as a function of the output load and the mains input voltage

Mains supply V; Hz 90; 60 90; 60 264; 50 264; 50

; I

(V; A) 19.558; 0 19.325; 4.62 19.559; 0 19.324; 4.62

Omax()

Omin()

–

O nom()

-------------------------------------------

100 %×

User manual Rev. 01 — 28 May 2010 16 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

Load regulation at 90 V; 60 Hz is calculated as follows:

(2)

Load regulation at 264 V; 50 Hz is calculated as follows:

(3)

3.4.2 Line regulation

Test conditions:

• The output voltage deviation is measured while the mains voltage on the input is

increased from 90 V to 264 V

• The measurement is repeated for different mains input voltages

Remark: The output voltage is measured at the end of the output cable. The load current

is 4.62 A.

The line regulation is calculated using the following equation:

(4)

Criteria to pass:

The output voltage deviation must remain within 0.05 %.

Load regulation at 90 V; 60 Hz is calculated using the following equation:

(5)

3.4.3 Ripple and noise PARD (Periodic And Random Deviation)

Ripple and noise are defined as the periodic or random signals over a frequency band of

10 Hz to 20 MHz.

Test Conditions:

• The measurement is made with an oscilloscope set to bandwidth of 20 MHz

• The output is shunted at the end of the output cable, by a 0.1 μF ceramic disk

capacitor and a 22 μF electrolytic capacitor, to simulate loading

Criteria to pass:

The output ripple and noise must remain within the specified limits 100 mV (peak-to-peak)

at a maximum load current of 4.62 A.

19.558V 19.325V–

19.5V

-----------------------------------------------

100 %× 1.19 %=

19.559V 19.324V–

19.5V

-----------------------------------------------

100 %× 1.21 %=

Table 10. Line regulation

Output voltage (at full load) as a function of the mains input voltage

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

(V) 19.325 19.325 19.325 19.324 19.324

Omax()

Omin()

–

O nom()

-------------------------------------------

100 %×

19.325V 19.324V–

19.5V

-----------------------------------------------

100 %× 0.005 %=

User manual Rev. 01 — 28 May 2010 17 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

3.4.4 Dynamic load response

Test Conditions:

• The adapter is subjected to a load change from 0 % to 100 % at a slew rate of

1A/ms

• The frequency of change is set to give the best readability of the deviation and setting

time

Remark: The voltage is measured at the end of the output cable.

Criteria to pass:

The output is not allowed to have an overshoot or undershoot beyond the specified limits

(+1 V to 0.5 V) after a load change.

Table 11. Ripple and noise PARD

Ripple and noise (at maximum load) as a function of the mains input voltage.

Mains supply V; Hz 90; 60 100; 50 115; 60 230; 50 264; 50

PARD (mV) 94 94 94 83 83

Table 12. Dynamic load response

Deviation of the output voltage at a load step from 4.62 A to 0 A and from 0 A to 4.62 A

Mains supply V; Hz 90; 60 230; 50

Deviation (mV

p-p

) 700 700

User manual Rev. 01 — 28 May 2010 18 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

CH1: PFC bus voltage

CH2: output current

Ch3: PFCTIMER pin

Ch4: output voltage

CH1: PFC bus voltage

CH2: output current

Ch3: PFCTIMER pin

Ch4: output voltage

a. Mains input 90 V; 60 Hz b. Mains input 90 V; 60 Hz (detail picture)

CH1: PFC bus voltage

CH2: output current

Ch3: PFCTIMER pin

Ch4: output voltage

CH1: PFC bus voltage

CH2: output current

Ch3: PFCTIMER pin

Ch4: output voltage

c. Mains input 230 V; 50 Hz d. Mains input 230 V; 50 Hz (detail picture)

Fig 11. Dynamic load response

019aaa023 019aaa024

019aaa025 019aaa026

User manual Rev. 01 — 28 May 2010 19 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

4. ElectroMagnetic Compatibility (EMC)

4.1 Conducted emission

Test Conditions:

• The adapter is subjected to maximum load

• The ground connection of the output cable is connected to EMC ground

Criteria to pass:

CISPR22 Class B with -10 dB production margin

(1) QP limit

(2) AV limit

(3) Peak reading

The conducted EMI measurement of 110 V neutral is close to 110 V line

Fig 12. Conducted EMI 110 V line

001aak816

f (MHz)

-1

101

100

(dBuV)

(1)

(2)

(3)

Table 13. Conducted EMI measurement 110 V line

Refer to Figure 12

points 1 and 2 on the peak reading graph

No. Frequency Correction

factor

Reading dBμV Emission dBμV Limit dBμV Margins dB

MHz dB QP AV QP AV QP AV QP AV

1 0.20112 0.12 32.67 27.68 32.79 27.80 63.56 53.56 −30.77 −25.76

2 24.36328 1.50 35.94 30.50 37.44 32.00 60.00 50.00 −22.56 −18.00

User manual Rev. 01 — 28 May 2010 20 of 32

NXP Semiconductors

UM10403

90 Watt notebook adapter with TEA1752T and TEA1791T

4.2 Immunity against lighting surges

Test conditions:

• Combination wave: 1.2/50 μs open circuit voltage and 8/20 μs short circuit current

• Test voltage: 2 kV

• L1 to L2: 2 Ω; L1 to PE, L2 to PE and L1 + L2 to PE: 12 Ω

• Phase angle: 0 °, 90 °, 180 ° and 270 °

• Number of tests: 5 positive and 5 negative

• Pulse repetition rate: 20 s

Test result:

• There is no disruption of functionality

(1) QP limit

(2) AV limit

(3) Peak reading

The conducted EMI measurement of 230 V neutral is close to 230 V line

Fig 13. Conducted EMI 230 V line

001aak817

f (MHz)

-1

101

100

(dBuV)

(3)

(2)

(1)

Table 14. Conducted EMI measurement 230 V line

Refer to Figure 13

points 1, 2 and 3 on the peak reading graph.

No. Frequency Correction

factor

Reading dBμV Emission dBμV Limit dBμV Margins dB

MHz dB QP AV QP AV QP AV QP AV

1 0.18906 0.09 38.38 37.05 38.47 37.14 64.508 54.08 −25.01 −16.94

2 0.43516 0.20 32.37 24.52 32.57 24.72 5715 47.15 −24.58 −22.43

3 25.11328 1.14 38.45 32.14 39.59 33.28 60.00 50.00 −20.41 −16.72

Page is loading ...

NXP TEA179X User guide

Brand: NXP

Model: TEA179X

Type: User guide

This manual is also suitable for

Download PDF

report

NXP TEA179X User guide

This manual is also suitable for

NXP TEA179X User guide

Related papers

Other documents