Danfoss CF-RF Room Thermostat Installation guide

Category
Thermostats
Type
Installation guide
088U0213
GB
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
D
Instruktion CF-RF Raumthermostat mit Infrarot-Bodensensor
DK
Vejledning CF-RF Rumtermostat med infrarød gulvsensor
F
Instruction Thermostat d’ambiance CF-RF avec Capteur au sol infrarouge
SE
Bruksanvisning CF-RF rumstermostate med infraröd golvsensor
PL
Instrukcja obsługi termostatu z czujnikiem podłogowym CF-RF
NL
Handleiding voor CF-RF kamerthermostaat met infrarood vloersensor
I
Istruzioni CF-RF con sensore a pavimento a raggi infrarossi
1VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
GB
Instruction . . . . . . . . . . . . . . . . . . . . . . . 3
D
Instruktion . . . . . . . . . . . . . . . . . . . . . . 13
DK
Vejledning . . . . . . . . . . . . . . . . . . . . . . 25
F
Instruction . . . . . . . . . . . . . . . . . . . . . . 35
SE
Bruksanvisning ..................45
PL
Instrukcja obsługi ................55
NL
Handleiding .....................65
I
Istruzioni ........................75
2 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
3VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
GB
Index
1. Functional Overview ...............................................4
2. Installation ...................................................................4
3. Temperature Settings ...............................................6
4. Transmission Test ......................................................9
5. Mounting .....................................................................9
6. Uninstallation ..........................................................10
7. Specifications ........................................................... 11
8. Troubleshooting ...................................................... 12
9. Figures and Illustrations ................................ A1-A2
GB
4 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
1. Functional Overview
Front - fig. 1
Up/down selector
Push button
Red LED (behind the cover)
InfraRed floor sensor
LED modes
Permanent light ON
No light OFF
Slow flashing Flashes
Fast flashing Flickers
Back - fig. 2
Back plate
Back plate lock/unlock (turn 90°)
Screw hole for wall mounting
Battery placement
Screw and wall plug
Note: To activate batteries please remove enclosed strips
from batteries
2. Installation
Note:
To activate batteries in the Room Thermostat, please
remove enclosed strips from the batteries.
The assignment of the Room Thermostats to the Master
Controller should be within 1½ m distance
5VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Activate Install mode on Master Controller
- fig. 1.
Use the menu selection button to select the
Install mode. Install LED flashes
Activate Install mode by pressing OK . Install
LED goes ON
Activate Install mode on Room Thermostat
Press the push button . LED and flicker
during communication
Select output on Master Controller
All available output LEDs on Master Controller
light up, and the first of them flashes
Press output selection button , to select
desired output (ashes) and accept with OK
All output LEDs go OFF. Selected output
stays ON shortly
Room Thermostat installation status
Satisfactory - LED goes OFF
Not satisfactory - LED flashes 5 times
Note: A Room Thermostat can be assigned to several
outputs if needed by repeating the installation process.
GB
6 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
3. Temperature Settings
Digital Display - fig. 1
Set value adjustment
Minimum temperature limitation
Maximum temperature limitation
Lock icon (settings locked from Remote
Controller, CF-RC)
Transmission link icon
Low battery indicator
Alarm icon
Timer icon (time program is active from
Remote Controller, CF-RC)
Room temperature
Floor surface temperature
Changing default display temperature - fig. 1.
1. The actual room temperature is shown in the
display as default
2. To change default display from actual room
temperature to actual floor surface tempera-
ture, press and hold the push button
until SET MAX is shown in the display
3. Press the button shortly and repeatedly
until or is flashing in the display
4. Press the up/down selector to select the
new default display temperature:
Room temperature
Floor surface temperature
7VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Setting of room temperature
1. Make sure actual room temperature is shown
in the display
2. Press the up/down selector to set the
desired room temperature value. SET is shown
in the display
3. When releasing the up/down selector the
display returns to actual temperature
Note: The thermostat regulates the floor heating system
according to room temperature set point, within the
maximum and minimum limitations defined for the floor
surface temperature
Room temperature limitation
1. Make sure actual room temperature is shown
in the display
2. Press the push button until SET MAX is
shown in the display
3. Press the up/down selector to set the
maximum room temperature limitation
4. Press the push button shortly, SET MIN is
shown in the display
5. Press the up/down selector to set the
minimum room temperature limitation
6. Press the push button shortly and the
actual floor surface temperature is shown in
the display
GB
8 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Floor surface temperature limitation
1. Ensure actual floor surface temperature is
shown in the display illustrated by
2. Press and hold the push button until SET
MAX is also shown in the display
3. Press the up/down selector to set the
maximum floor surface temperature limitation
4. Press the push button shortly, SET MIN is
also shown in the display
5. Press the up/down selector to set the mini-
mum floor surface temperature limitation
IMPORTANT!
As heat emission from the floor may vary slightly
depending on floor covering - and thereby cause
inaccurate temperature measurement - it may be
necessary to adjust the setting of max. and min.
floor surface temperatures accordingly.
! It is important always to follow recommendations
from the floor manufacturer regarding max. floor
surface temperature.
! It is recommended always to include mixing shunt
for floor heating circuits in order to ensure optimal
flow temperature. - In addition to minimised energy
consumption, correct setting of the flow tempera-
ture will eliminate the risk of excessive heat transfer
to the floor.
9VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
4. Transmission Test
Initiate transmission test on Room Thermostat
- fig. 1
Press the push button
LED goes ON
Link test is satisfactory
LED goes OFF
Link test is unsatisfactory
LED flashes 5 times
No link connection to Room Thermostat
Try to relocate Room Thermostat in the room
Or install Repeater Unit (CF-RU) and locate
between Master Controller and Room
Thermostat
Note: Master Controller output LED(s) connected to the
Room thermostat, flash(es) during link test
5. Mounting
Placing the Room Thermostat - fig. 3
The Room Thermostat should be placed in
accordance with fig. 3
IMPORTANT!
Wherever possible, the room thermostat should
be installed at a place where the effect of sunlight,
GB
10 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
strong artificial light (e.g. halogen spotlight),
draught, other heat-emitting equipment (e.g. TVs)
etc. is avoided.
! Please note that no furniture, rugs etc. should be
permanently placed within the area of the InfraRed
Floor Sensor as shown in fig. 3.
Mounting - fig. 2
1. Mount the back plate with the two screws
and wall plugs via the screw holes in the
back plate
2. Slide thermostat into place on the back plate
3. If desired lock the thermostat to the back plate
with Allen key (turn 90°)
6. Uninstallation
Activate Uninstall mode on Master Controller
- fig. 1
Use the Menu selection button to choose
the Uninstall menu. Uninstall LED flashes
Activate Uninstall mode by pressing OK .
Uninstall LED goes ON
Deselect output on Master Controller
Select output to be removed by output selec-
tion button
Remove ashing output with OK
11VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
7. Specifications
Temperature setting range 5-35°C
Transmission frequency 868.42MHz
Transmission range in normal
buildings (up to)
30m
Transmission power < 1mW
Battery Alkaline 2xAA, 1.5V
Battery lifetime (up to) 1-3 years
Ambient temperature 0-50°C
IP class 21
Floor ensor accuracy +/- 1°C
Floor sensor emission
coefficient
0.9
GB
12 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Error Indication Possible Cause
The LED, and
flashes every 5th minute
Low battery
The LED, and
flashes every 30 sec.
Critical low battery
The LED, , and
flashes
Critical low battery -
transmission has stopped
The LED, and
flashes 5 times
Installation/link Test is
unsatisfactory
E03 and
Actuator error on output
(CF-MC)
E05 and
Room temperature below
5°C
8. Troubleshooting
Handleiding voor CF-RF kamerthermostaat met infrarood vloersensor
VI.UH.R3.1C Geproduceerd door Danfoss Floor Heating Hydronics 08.200974
8. Probleemoplossing
Foutmelding Mogelijke oorzaken
De led, en knipperen
om de 5 minuten
Batterij bijna leeg
De led, en knipperen
Batterij op kritisch peil
De led, , en
knipperen
Batterij op kritisch peil
– transmissie gestopt
De led, en knipperen
5 keer
Aanmelden/Verbin-melden/Verbin-
dingstest niet gelukt
E03 en
Motorfout op uitgang
(CF-MC)
E05 en
Kamertemperatuur
lager dan 5°C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89

Danfoss CF-RF Room Thermostat Installation guide

Category
Thermostats
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI