CF-RF Room Thermostat

Danfoss CF-RF Room Thermostat Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss CF-RF Room Thermostat Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
088U0213
GB
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
D
Instruktion CF-RF Raumthermostat mit Infrarot-Bodensensor
DK
Vejledning CF-RF Rumtermostat med infrarød gulvsensor
F
Instruction Thermostat d’ambiance CF-RF avec Capteur au sol infrarouge
SE
Bruksanvisning CF-RF rumstermostate med infraröd golvsensor
PL
Instrukcja obsługi termostatu z czujnikiem podłogowym CF-RF
NL
Handleiding voor CF-RF kamerthermostaat met infrarood vloersensor
I
Istruzioni CF-RF con sensore a pavimento a raggi infrarossi
1VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
GB
Instruction . . . . . . . . . . . . . . . . . . . . . . . 3
D
Instruktion . . . . . . . . . . . . . . . . . . . . . . 13
DK
Vejledning . . . . . . . . . . . . . . . . . . . . . . 25
F
Instruction . . . . . . . . . . . . . . . . . . . . . . 35
SE
Bruksanvisning ..................45
PL
Instrukcja obsługi ................55
NL
Handleiding .....................65
I
Istruzioni ........................75
2 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
3VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
GB
Index
1. Functional Overview ...............................................4
2. Installation ...................................................................4
3. Temperature Settings ...............................................6
4. Transmission Test ......................................................9
5. Mounting .....................................................................9
6. Uninstallation ..........................................................10
7. Specifications ........................................................... 11
8. Troubleshooting ...................................................... 12
9. Figures and Illustrations ................................ A1-A2
GB
4 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
1. Functional Overview
Front - fig. 1
Up/down selector
Push button
Red LED (behind the cover)
InfraRed floor sensor
LED modes
Permanent light ON
No light OFF
Slow flashing Flashes
Fast flashing Flickers
Back - fig. 2
Back plate
Back plate lock/unlock (turn 90°)
Screw hole for wall mounting
Battery placement
Screw and wall plug
Note: To activate batteries please remove enclosed strips
from batteries
2. Installation
Note:
To activate batteries in the Room Thermostat, please
remove enclosed strips from the batteries.
The assignment of the Room Thermostats to the Master
Controller should be within 1½ m distance
5VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Activate Install mode on Master Controller
- fig. 1.
Use the menu selection button to select the
Install mode. Install LED flashes
Activate Install mode by pressing OK . Install
LED goes ON
Activate Install mode on Room Thermostat
Press the push button . LED and flicker
during communication
Select output on Master Controller
All available output LEDs on Master Controller
light up, and the first of them flashes
Press output selection button , to select
desired output (ashes) and accept with OK
All output LEDs go OFF. Selected output
stays ON shortly
Room Thermostat installation status
Satisfactory - LED goes OFF
Not satisfactory - LED flashes 5 times
Note: A Room Thermostat can be assigned to several
outputs if needed by repeating the installation process.
GB
6 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
3. Temperature Settings
Digital Display - fig. 1
Set value adjustment
Minimum temperature limitation
Maximum temperature limitation
Lock icon (settings locked from Remote
Controller, CF-RC)
Transmission link icon
Low battery indicator
Alarm icon
Timer icon (time program is active from
Remote Controller, CF-RC)
Room temperature
Floor surface temperature
Changing default display temperature - fig. 1.
1. The actual room temperature is shown in the
display as default
2. To change default display from actual room
temperature to actual floor surface tempera-
ture, press and hold the push button
until SET MAX is shown in the display
3. Press the button shortly and repeatedly
until or is flashing in the display
4. Press the up/down selector to select the
new default display temperature:
Room temperature
Floor surface temperature
7VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Setting of room temperature
1. Make sure actual room temperature is shown
in the display
2. Press the up/down selector to set the
desired room temperature value. SET is shown
in the display
3. When releasing the up/down selector the
display returns to actual temperature
Note: The thermostat regulates the floor heating system
according to room temperature set point, within the
maximum and minimum limitations defined for the floor
surface temperature
Room temperature limitation
1. Make sure actual room temperature is shown
in the display
2. Press the push button until SET MAX is
shown in the display
3. Press the up/down selector to set the
maximum room temperature limitation
4. Press the push button shortly, SET MIN is
shown in the display
5. Press the up/down selector to set the
minimum room temperature limitation
6. Press the push button shortly and the
actual floor surface temperature is shown in
the display
GB
8 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Floor surface temperature limitation
1. Ensure actual floor surface temperature is
shown in the display illustrated by
2. Press and hold the push button until SET
MAX is also shown in the display
3. Press the up/down selector to set the
maximum floor surface temperature limitation
4. Press the push button shortly, SET MIN is
also shown in the display
5. Press the up/down selector to set the mini-
mum floor surface temperature limitation
IMPORTANT!
As heat emission from the floor may vary slightly
depending on floor covering - and thereby cause
inaccurate temperature measurement - it may be
necessary to adjust the setting of max. and min.
floor surface temperatures accordingly.
! It is important always to follow recommendations
from the floor manufacturer regarding max. floor
surface temperature.
! It is recommended always to include mixing shunt
for floor heating circuits in order to ensure optimal
flow temperature. - In addition to minimised energy
consumption, correct setting of the flow tempera-
ture will eliminate the risk of excessive heat transfer
to the floor.
9VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
4. Transmission Test
Initiate transmission test on Room Thermostat
- fig. 1
Press the push button
LED goes ON
Link test is satisfactory
LED goes OFF
Link test is unsatisfactory
LED flashes 5 times
No link connection to Room Thermostat
Try to relocate Room Thermostat in the room
Or install Repeater Unit (CF-RU) and locate
between Master Controller and Room
Thermostat
Note: Master Controller output LED(s) connected to the
Room thermostat, flash(es) during link test
5. Mounting
Placing the Room Thermostat - fig. 3
The Room Thermostat should be placed in
accordance with fig. 3
IMPORTANT!
Wherever possible, the room thermostat should
be installed at a place where the effect of sunlight,
GB
10 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
strong artificial light (e.g. halogen spotlight),
draught, other heat-emitting equipment (e.g. TVs)
etc. is avoided.
! Please note that no furniture, rugs etc. should be
permanently placed within the area of the InfraRed
Floor Sensor as shown in fig. 3.
Mounting - fig. 2
1. Mount the back plate with the two screws
and wall plugs via the screw holes in the
back plate
2. Slide thermostat into place on the back plate
3. If desired lock the thermostat to the back plate
with Allen key (turn 90°)
6. Uninstallation
Activate Uninstall mode on Master Controller
- fig. 1
Use the Menu selection button to choose
the Uninstall menu. Uninstall LED flashes
Activate Uninstall mode by pressing OK .
Uninstall LED goes ON
Deselect output on Master Controller
Select output to be removed by output selec-
tion button
Remove ashing output with OK
11VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
7. Specifications
Temperature setting range 5-35°C
Transmission frequency 868.42MHz
Transmission range in normal
buildings (up to)
30m
Transmission power < 1mW
Battery Alkaline 2xAA, 1.5V
Battery lifetime (up to) 1-3 years
Ambient temperature 0-50°C
IP class 21
Floor ensor accuracy +/- 1°C
Floor sensor emission
coefficient
0.9
GB
12 VI.UH.R3.1C Produced by Danfoss Floor Heating Hydronics 08.2009
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Error Indication Possible Cause
The LED, and
flashes every 5th minute
Low battery
The LED, and
flashes every 30 sec.
Critical low battery
The LED, , and
flashes
Critical low battery -
transmission has stopped
The LED, and
flashes 5 times
Installation/link Test is
unsatisfactory
E03 and
Actuator error on output
(CF-MC)
E05 and
Room temperature below
5°C
8. Troubleshooting
Handleiding voor CF-RF kamerthermostaat met infrarood vloersensor
VI.UH.R3.1C Geproduceerd door Danfoss Floor Heating Hydronics 08.200974
8. Probleemoplossing
Foutmelding Mogelijke oorzaken
De led, en knipperen
om de 5 minuten
Batterij bijna leeg
De led, en knipperen
Batterij op kritisch peil
De led, , en
knipperen
Batterij op kritisch peil
– transmissie gestopt
De led, en knipperen
5 keer
Aanmelden/Verbin-melden/Verbin-
dingstest niet gelukt
E03 en
Motorfout op uitgang
(CF-MC)
E05 en
Kamertemperatuur
lager dan 5°C
/