Tripp Lite SRCABLELADDER Owner's manual

1

Owner’s Manual

SmartRack

™

Accessories

Model: SRCABLELADDER

1 – Introduction 2

1-2 Tools Required 2

3 – Installation 3

3-2 Ladder Modiﬁcation (Optional) 4

3-4 Installation Across Aisle 5

3-6 Ground Connection 7

Français 17

1-1 Parts List 2

2 – Important Safety Instructions 2

3-1 Planning 3

3-3 Ladder Assembly 4

3-5 Installation Within Row 6

Español 9

4 – Storage and Service 8

5 – Warranty and Warranty Registration 8

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

WARRANTY

REGISTRATION:

register online today for a

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

201105211 93-2973.indb 1 5/23/2011 12:56:45 PM

2

1 – Introduction

SRCABLELADDER provides roof-mounted cable routing for Tripp Lite’s SmartRack Enclosures, allowing cable bundles to span aisles and/or

spaces between enclosures in the same row. Note: Standard installation of SRCABLELADDER requires Tripp Lite’s SRCABLETRAY accessory,

sold separately.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this

manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may invalidate the warranty and

cause property damage and/or personal injury.

• Installinacontrolledindoorenvironment,awayfrommoisture,temperatureextremes,ammableliquidsandgasses,conductive

contaminants, dust and direct sunlight.

• Providesuitablegroundinginaccordancewithallapplicableelectricalwiringregulations.

• Donotattempttoclimborwalkacrossanypartoftheladder.

• Whenusingtoolstocutordrillmetal,useeyeprotectionandfollowallothersafetyprecautionsrecommendedbythetoolmanufacturerand

requiredbyapplicablesafetyregulations.

• Usecautionandwearsafetygloveswhenhandlingmetalpartsthathavebeencuttolength.Sharpedgescancausepersonalinjuryand

property damage.

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonablybeexpectedtocausethefailureofthelife

supportequipmentortosignicantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofa

ammableanestheticmixturewithair,oxygenornitrousoxide.

• 13mmWrenchorCrescentWrench

• TapeMeasure

• Hacksaw(optional)

• Drillwith3/8-inchBit(optional)

LadderSections(2)

AssemblyBrackets(4)

ClevisPins(8)

CotterPins(8)

GroundBrackets(2)

M6Hex-HeadBolts(2)

24-inchGroundCables(3)

M6LockWashers(4)

M6HexNuts(2)

LadderClamp(4)

M10x60mmCarriageBolts(2)

M10LockWashers(2)

M10HexNuts(2)

Ifanypartsaremissing,visitwww.tripplite.com/support.

1-1 Parts List

2 – Important Safety Instructions

1-2 Tools Required

A A D

B E H

C

J K L M

F I

B

C

D

E

F

G

H

I

J

K

L

M

G

201105211 93-2973.indb 2 5/23/2011 12:56:45 PM

3

SRCABLELADDER can provide enclosure-to-enclosure cable routing across an aisle or within a single row. You can combine multiple

SRCABLELADDERandSRCABLETRAYaccessoriestomeetthecableroutingneedsofalmostanycongurationofSmartRackEnclosures,

butplanningandmeasurementarerequiredtoensureasecuret.TrippLiterecommendsthatyoureadtheentiremanualinadvancetogaina

clear understanding of the installation process and accessory positioning.

Sample Cable Routing Conﬁguration (Top View)

UseatapemeasuretodeterminethedistancethatSRCABLELADDERwillbridge.(Preassemblingtheladdersectionswillallowyoutoobserve

theirattachmentpointsinplaceforamoreaccuratemeasurement.)

ThestandardlengthofSRCABLELADDERis10feet.Ifthestandardlengthandthedistancebetweenattachmentpointsdiffer,adjustingthe

positionoftheSRCABLETRAYaccessorieswillallowyoutochangethedistancebetweenattachmentpoints.Ifnecessary,youcanuseasingle

laddersectioninsteadoftwosections,reducingtheoverallladderlengthtoapproximately5feet.Inaddition,theassemblybracketsattheends

of the ladder sections will allow minor adjustments if you install them without pins, and you can add a few inches to the length of the ladder

byusingthealternatepinholesforassembly.IftheavailableadjustmentswillnotaccommodatetheSRCABLELADDERaccessory,youmust

cut one of the ladder sections. See Section 3-2 Ladder Modicationforinstructions.IftheSRCABLELADDERaccessorywilltwithout

modication,proceedtoSection 3-3 Ladder Assembly.

Note: Prior to installation, you must install the SRCABLETRAY accessory (sold separately) on each enclosure that will be linked by the

SRCABLELADDER accessory. For ordering information, visit www.tripplite.com.

3-1 Planning

3 – Installation

SRCABLETRAY

SRCABLELADDER installed

between enclosures across an aisle.

SRCABLELADDER installed

between enclosures within a row.

201105211 93-2973.indb 3 5/23/2011 12:56:45 PM

4

3-2 Ladder Modiﬁcation (Optional)

Warning: When using tools to cut or drill metal, use eye protection and follow all other safety precautions recommended by the tool

manufacturer and required by applicable safety regulations. Use caution and wear safety gloves when handling metal parts that have

been cut to length. Sharp edges can cause personal injury and property damage.

Note: Do not modify the SRCABLELADDER accessory unless you have followed the instructions in Section 3-1 Planning and determined that

modication is required. If modication is not required, proceed to Section 3-3 Ladder Assembly.

Measureandmarkthecableladdersectionthatwillbecut.

Useahacksaworothermetal-cuttingtooltocutthroughtheladdersection.Makesureyourcutisperpendiculartothelengthoftheladder

and use a metal-cutting tool that will not bend or crush the ladder section.

(Optional)Aftercutting,useadrillwitha3/8-inchbittodrillnewpinholesinendoftheladdersection.Comparethemodiedendofthe

laddersectionwiththeunmodiedendtodeterminewhereholesshouldbedrilled.Makesurethattheholelocationmatchesyourplanning

and measurements. You may omit this step, but drilling the pin holes and installing the pins will make the SRCABLELADDER accessory

more stable.

3-3 Ladder Assembly

Assemble the two ladder clamps

A

withtheM10carriagebolts

B

, washers

C

andhexnuts

D

as seen in the diagram. For now,

only tighten the nuts far enough to keep the clamps assembled

together.

Join the ladder sections

E

by inserting each side into the ladder

clamps

A

until they are stopped by the bolts

B

.Whenthesections

are joined, you can now secure the clamp by fully tightening the

nuts.

3 – Installation (continued)

1

2

3

1

2

1

2

A

B

C

D

E

X2

A

E

B

201105211 93-2973.indb 4 5/23/2011 12:56:45 PM

5

Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed across an aisle. If the SRCABLELADDER

accessory will be installed within a row of enclosures, follow the instructions in Section 3-5 Installation Within Row instead.

3-4 Installation Across Aisle

Insertfourassemblybrackets

A

into the ends of the ladder. The

hookedendsofthebracketsshouldbeexposed.Whentheladderis

oriented so that the ladder’s rungs are above the ladder’s side rails,

the hooked ends of the brackets should point down, as shown in

the drawing.

Align the pin holes in the ladder sections with the pin holes

in the assembly brackets and insert clevis pins

B

into the pin

holes(4total).Thisstepmaybeomittedtoprovideadditional

installationexibility,butinstallingthepinswillmakethe

SRCABLELADDER accessory more stable. Warning: If you

choose not to install the clevis pins, make sure at least 25% of

the length of each assembly bracket is inside the ladder.

After inserting the clevis pins, insert a cotter pin

C

through the

holeattheendofeachclevispin.(Thestraightsectionofthe

cotterpingoesthroughthehole.)

Usinganassistant,lifttheSRCABLELADDERaccessory

(rungsupward)andinserttheexposedhookendsofthe

assembly brackets

D

into the corresponding slots

E

in the

SRCABLETRAY accessories installed at the top of each

enclosure.Thehooksshouldttheslotssecurelybyslidingdown

to engage the edge of the slot. Note: There are two levels of slots.

Use the slots that match your application best.

3 – Installation (continued)

2

3

B

1

2

3

4

A

C

D

E

201105211 93-2973.indb 5 5/23/2011 12:56:46 PM

6

Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed within a row of enclosures. If the

SRCABLELADDER accessory will be installed across an aisle, follow the instructions in Section 3-4 Installation Across Aisle instead.

3-5 Installation Within Row

Insertfourassemblybrackets

A

in the open ends of the ladder,

hookedendrst.Whentheladderisorientedsothattheladder’s

rungs are above the ladder’s side rails, the hooked ends of the

brackets should point down, as shown in the drawing.

Align the pin holes in the ladder sections with the pin holes

in the assembly brackets and insert clevis pins

B

into the pin

holes(4total).Thisstepmaybeomittedtoprovideadditional

installationexibility,butinstallingthepinswillmakethe

SRCABLELADDER accessory more stable. Warning: If you

choose not to install the clevis pins, make sure at least 25% of

the length of each assembly bracket is inside the ladder.

After inserting the clevis pins, insert a cotter pin

C

through the

holeattheendofeachclevispin.(Thestraightsectionofthe

cotterpingoesthroughthehole.)

Usinganassistant,lifttheSRCABLELADDERaccessory(rungs

upward)andaligntheholesattheendsoftheassemblybrackets

D

with the corresponding holes

E

in the SRCABLETRAY

accessories installed at the top of each enclosure. Note: There are

two levels of holes. Use the holes that match your application best.

Align the pin holes and insert clevis pins

F

into each of the pin

holes(4total).

3 – Installation (continued)

2

3

B

C

1

2

3

4

5

4

D

E

F

A

201105211 93-2973.indb 6 5/23/2011 12:56:47 PM

7

3-5 Installation Within Row (continued)

3-6 Ground Connection

After installing the SRCABLELADDER accessory, determine

where to place ground brackets by noting the distance between

one end of the ladder and the grounding post

A

at the corner of the

nearest SRCABLETRAY accessory.

Placeagroundbracket

B

near the end of the SRCABLELADDER

accessory’sleganduseahex-headbolt

C

to secure it.

Usetheincludedhexnutsandlockwashers

G

to connect one end

of the included ground cable

H

to a grounding post

I

at the corner

of the nearest SRCABLETRAY accessory and connect the other

end to the grounding post

J

of the ground bracket attached to the

SRCABLELADDERaccessory.Repeatsteps1to3fortheother

end of the SRCABLELADDER accessory.

After inserting the clevis pins, insert a cotter pin

G

through the

holeattheendofeachclevispin.(Thestraightsectionofthe

cotterpingoesthroughthehole.)

3 – Installation (continued)

1

6

2

3

G

6

A

1

2

3

B

C

G

H

I

J

201105211 93-2973.indb 7 5/23/2011 12:56:48 PM

8

4 – Storage and Service

5 – Warranty and Warranty Registration

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Storage

Theunitmustbestoredinaclean,secureenvironmentwithatemperaturelessthan40°C(104°F)andarelativehumiditylessthan90%

(non-condensing).Storetheunitinitsoriginalshippingcontainerifpossible.

Service

YourTrippLiteproductiscoveredbythewarrantydescribedinthismanual.AvarietyofExtendedWarrantyandOn-SiteServicePrograms

are also available from Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service,

follow these steps:

1.Reviewtheinstallationandoperationproceduresinthismanualtoinsurethattheserviceproblemdoesnotoriginatefromamisreadingofthe

instructions.

2.Iftheproblemcontinues,donotcontactorreturntheproducttothedealer.Instead,visitwww.tripplite.com/support.

3.Iftheproblemrequiresservice,visitwww.tripplite.com/supportandclicktheProductReturnslink.FromhereyoucanrequestaReturned

MaterialAuthorization(RMA)number,whichisrequiredforservice.Thissimpleon-lineformwillaskforyourunit’smodelandserial

numbers,alongwithothergeneralpurchaserinformation.TheRMAnumber,alongwithshippinginstructionswillbeemailedtoyou.Any

damages(direct,indirect,specialorconsequential)totheproductincurredduringshipmenttoTrippLiteoranauthorizedTrippLiteservice

centerisnotcoveredunderwarranty.ProductsshippedtoTrippLiteoranauthorizedTrippLiteservicecentermusthavetransportation

chargesprepaid.MarktheRMAnumberontheoutsideofthepackage.Iftheproductiswithinitswarrantyperiod,encloseacopyofyour

salesreceipt.ReturntheproductforserviceusinganinsuredcarriertotheaddressgiventoyouwhenyourequesttheRMA.

Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship

foraperiodof5yearsfromthedateofinitialpurchase.Iftheproductshouldprovedefectiveinmaterialorworkmanshipwithinthatperiod,

Seller will repair or replace the product, in its sole discretion.

THISWARRANTYDOESNOTAPPLYTONORMALWEARORTODAMAGERESULTINGFROMACCIDENT,MISUSE,ABUSE

ORNEGLECT.SELLERMAKESNOEXPRESSWARRANTIESOTHERTHANTHEWARRANTYEXPRESSLYSETFORTHHEREIN.

EXCEPTTOTHEEXTENTPROHIBITEDBYAPPLICABLELAW,ALLIMPLIEDWARRANTIES,INCLUDINGALLWARRANTIESOF

MERCHANTABILITYORFITNESS,ARELIMITEDINDURATIONTOTHEWARRANTYPERIODSETFORTHABOVE;ANDTHIS

WARRANTYEXPRESSLYEXCLUDESALLINCIDENTALANDCONSEQUENTIALDAMAGES.(Somestatesdonotallowlimitations

onhowlonganimpliedwarrantylasts,andsomestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sothe

abovelimitationsorexclusionsmaynotapplytoyou.ThisWarrantygivesyouspeciclegalrights,andyoumayhaveotherrightswhichvary

fromjurisdictiontojurisdiction.)

TrippLite;1111W.35thStreet;ChicagoIL60609;USA

WARNING:Theindividualusershouldtakecaretodeterminepriortousewhetherthisdeviceissuitable,adequateorsafefortheuseintended.

Sinceindividualapplicationsaresubjecttogreatvariation,themanufacturermakesnorepresentationorwarrantyastothesuitabilityortness

ofthesedevicesforanyspecicapplication.

Warranty Registration

Visitwww.tripplite.com/warrantytodaytoregisterthewarrantyforyournewTrippLiteproduct.You’llbeautomaticallyenteredintoadrawing

for a chance to win a FREE Tripp Lite product!*

*Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.

TrippLitehasapolicyofcontinuousimprovement.Specicationsaresubjecttochangewithoutnotice.

201105211 • 932973-EN

201105211 93-2973.indb 8 5/23/2011 12:56:48 PM

9

Manual del propietario

Accesorios SmartRack

™

Modelo: SRCABLELADDER

1 – Introducción 10

1-2 Herramientas requeridas 10

3 – Instalación 11

3-2 Modiﬁcación de la escalera (Opcional) 12

3-4 Instalación en pasillo 13

3-6 Conexión a tierra 15

1-1 Lista de piezas 10

2 – Instrucciones de seguridad importantes 10

3-1 Planiﬁcación 11

3-3 Ensamblado de la escalera 12

3-5 Instalación en una ﬁla 14

4 – Almacenamiento y servicio 16

5 – Garantía 16

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Français 17

English 1

201105211 93-2973.indb 9 5/23/2011 12:56:49 PM

Page is loading ...

Tripp Lite SRCABLELADDER Owner's manual

This manual is also suitable for

Tripp Lite SRCABLELADDER Owner's manual

in other languages

Related papers

Other documents