Tripp Lite SRCABLELADDER Owner's manual

Category
Rack accessories
Type
Owner's manual

This manual is also suitable for

1
Owner’s Manual
SmartRack
Accessories
Model: SRCABLELADDER
1 – Introduction 2
1-2 Tools Required 2
3 – Installation 3
3-2 Ladder Modification (Optional) 4
3-4 Installation Across Aisle 5
3-6 Ground Connection 7
Français 17
1-1 Parts List 2
2 – Important Safety Instructions 2
3-1 Planning 3
3-3 Ladder Assembly 4
3-5 Installation Within Row 6
Español 9
4 – Storage and Service 8
5 – Warranty and Warranty Registration 8
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. All trademarks are the sole property of their respective owners.
WARRANTY
REGISTRATION:
register online today for a
chance to win a FREE Tripp Lite
product—www.tripplite.com/warranty
201105211 93-2973.indb 1 5/23/2011 12:56:45 PM
2
1 – Introduction
SRCABLELADDER provides roof-mounted cable routing for Tripp Lite’s SmartRack Enclosures, allowing cable bundles to span aisles and/or
spaces between enclosures in the same row. Note: Standard installation of SRCABLELADDER requires Tripp Lite’s SRCABLETRAY accessory,
sold separately.
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this
manual. Read all instructions and warnings thoroughly before attempting installation. Failure to comply may invalidate the warranty and
cause property damage and/or personal injury.
• Installinacontrolledindoorenvironment,awayfrommoisture,temperatureextremes,ammableliquidsandgasses,conductive
contaminants, dust and direct sunlight.
• Providesuitablegroundinginaccordancewithallapplicableelectricalwiringregulations.
• Donotattempttoclimborwalkacrossanypartoftheladder.
• Whenusingtoolstocutordrillmetal,useeyeprotectionandfollowallothersafetyprecautionsrecommendedbythetoolmanufacturerand
requiredbyapplicablesafetyregulations.
• Usecautionandwearsafetygloveswhenhandlingmetalpartsthathavebeencuttolength.Sharpedgescancausepersonalinjuryand
property damage.
• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonablybeexpectedtocausethefailureofthelife
supportequipmentortosignicantlyaffectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthepresenceofa
ammableanestheticmixturewithair,oxygenornitrousoxide.
• 13mmWrenchorCrescentWrench
• TapeMeasure
• Hacksaw(optional)
• Drillwith3/8-inchBit(optional)
LadderSections(2)
AssemblyBrackets(4)
ClevisPins(8)
CotterPins(8)
GroundBrackets(2)
M6Hex-HeadBolts(2)
24-inchGroundCables(3)
M6LockWashers(4)
M6HexNuts(2)
LadderClamp(4)
M10x60mmCarriageBolts(2)
M10LockWashers(2)
M10HexNuts(2)
Ifanypartsaremissing,visitwww.tripplite.com/support.
1-1 Parts List
2 – Important Safety Instructions
1-2 Tools Required
A A D
B E H
C
J K L M
F I
B
C
D
E
F
G
H
I
J
K
L
M
G
201105211 93-2973.indb 2 5/23/2011 12:56:45 PM
3
SRCABLELADDER can provide enclosure-to-enclosure cable routing across an aisle or within a single row. You can combine multiple
SRCABLELADDERandSRCABLETRAYaccessoriestomeetthecableroutingneedsofalmostanycongurationofSmartRackEnclosures,
butplanningandmeasurementarerequiredtoensureasecuret.TrippLiterecommendsthatyoureadtheentiremanualinadvancetogaina
clear understanding of the installation process and accessory positioning.
Sample Cable Routing Configuration (Top View)
UseatapemeasuretodeterminethedistancethatSRCABLELADDERwillbridge.(Preassemblingtheladdersectionswillallowyoutoobserve
theirattachmentpointsinplaceforamoreaccuratemeasurement.)
ThestandardlengthofSRCABLELADDERis10feet.Ifthestandardlengthandthedistancebetweenattachmentpointsdiffer,adjustingthe
positionoftheSRCABLETRAYaccessorieswillallowyoutochangethedistancebetweenattachmentpoints.Ifnecessary,youcanuseasingle
laddersectioninsteadoftwosections,reducingtheoverallladderlengthtoapproximately5feet.Inaddition,theassemblybracketsattheends
of the ladder sections will allow minor adjustments if you install them without pins, and you can add a few inches to the length of the ladder
byusingthealternatepinholesforassembly.IftheavailableadjustmentswillnotaccommodatetheSRCABLELADDERaccessory,youmust
cut one of the ladder sections. See Section 3-2 Ladder Modicationforinstructions.IftheSRCABLELADDERaccessorywilltwithout
modication,proceedtoSection 3-3 Ladder Assembly.
Note: Prior to installation, you must install the SRCABLETRAY accessory (sold separately) on each enclosure that will be linked by the
SRCABLELADDER accessory. For ordering information, visit www.tripplite.com.
3-1 Planning
3 – Installation
SRCABLETRAY
SRCABLETRAY
SRCABLETRAY
SRCABLELADDER installed
between enclosures across an aisle.
SRCABLELADDER installed
between enclosures within a row.
201105211 93-2973.indb 3 5/23/2011 12:56:45 PM
4
3-2 Ladder Modification (Optional)
Warning: When using tools to cut or drill metal, use eye protection and follow all other safety precautions recommended by the tool
manufacturer and required by applicable safety regulations. Use caution and wear safety gloves when handling metal parts that have
been cut to length. Sharp edges can cause personal injury and property damage.
Note: Do not modify the SRCABLELADDER accessory unless you have followed the instructions in Section 3-1 Planning and determined that
modication is required. If modication is not required, proceed to Section 3-3 Ladder Assembly.
Measureandmarkthecableladdersectionthatwillbecut.
Useahacksaworothermetal-cuttingtooltocutthroughtheladdersection.Makesureyourcutisperpendiculartothelengthoftheladder
and use a metal-cutting tool that will not bend or crush the ladder section.
(Optional)Aftercutting,useadrillwitha3/8-inchbittodrillnewpinholesinendoftheladdersection.Comparethemodiedendofthe
laddersectionwiththeunmodiedendtodeterminewhereholesshouldbedrilled.Makesurethattheholelocationmatchesyourplanning
and measurements. You may omit this step, but drilling the pin holes and installing the pins will make the SRCABLELADDER accessory
more stable.
3-3 Ladder Assembly
Assemble the two ladder clamps
A
withtheM10carriagebolts
B
, washers
C
andhexnuts
D
as seen in the diagram. For now,
only tighten the nuts far enough to keep the clamps assembled
together.
Join the ladder sections
E
by inserting each side into the ladder
clamps
A
until they are stopped by the bolts
B
.Whenthesections
are joined, you can now secure the clamp by fully tightening the
nuts.
3 – Installation (continued)
1
2
3
1
2
1
2
A
B
C
D
E
X2
A
E
B
201105211 93-2973.indb 4 5/23/2011 12:56:45 PM
5
Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed across an aisle. If the SRCABLELADDER
accessory will be installed within a row of enclosures, follow the instructions in Section 3-5 Installation Within Row instead.
3-4 Installation Across Aisle
Insertfourassemblybrackets
A
into the ends of the ladder. The
hookedendsofthebracketsshouldbeexposed.Whentheladderis
oriented so that the ladders rungs are above the ladders side rails,
the hooked ends of the brackets should point down, as shown in
the drawing.
Align the pin holes in the ladder sections with the pin holes
in the assembly brackets and insert clevis pins
B
into the pin
holes(4total).Thisstepmaybeomittedtoprovideadditional
installationexibility,butinstallingthepinswillmakethe
SRCABLELADDER accessory more stable. Warning: If you
choose not to install the clevis pins, make sure at least 25% of
the length of each assembly bracket is inside the ladder.
After inserting the clevis pins, insert a cotter pin
C
through the
holeattheendofeachclevispin.(Thestraightsectionofthe
cotterpingoesthroughthehole.)
Usinganassistant,lifttheSRCABLELADDERaccessory
(rungsupward)andinserttheexposedhookendsofthe
assembly brackets
D
into the corresponding slots
E
in the
SRCABLETRAY accessories installed at the top of each
enclosure.Thehooksshouldttheslotssecurelybyslidingdown
to engage the edge of the slot. Note: There are two levels of slots.
Use the slots that match your application best.
3 – Installation (continued)
2
3
B
B
1
1
2
3
4
4
A
C
D
E
201105211 93-2973.indb 5 5/23/2011 12:56:46 PM
6
Note: Follow the instructions in this section only if the SRCABLELADDER accessory will be installed within a row of enclosures. If the
SRCABLELADDER accessory will be installed across an aisle, follow the instructions in Section 3-4 Installation Across Aisle instead.
3-5 Installation Within Row
Insertfourassemblybrackets
A
in the open ends of the ladder,
hookedendrst.Whentheladderisorientedsothattheladder’s
rungs are above the ladders side rails, the hooked ends of the
brackets should point down, as shown in the drawing.
Align the pin holes in the ladder sections with the pin holes
in the assembly brackets and insert clevis pins
B
into the pin
holes(4total).Thisstepmaybeomittedtoprovideadditional
installationexibility,butinstallingthepinswillmakethe
SRCABLELADDER accessory more stable. Warning: If you
choose not to install the clevis pins, make sure at least 25% of
the length of each assembly bracket is inside the ladder.
After inserting the clevis pins, insert a cotter pin
C
through the
holeattheendofeachclevispin.(Thestraightsectionofthe
cotterpingoesthroughthehole.)
Usinganassistant,lifttheSRCABLELADDERaccessory(rungs
upward)andaligntheholesattheendsoftheassemblybrackets
D
with the corresponding holes
E
in the SRCABLETRAY
accessories installed at the top of each enclosure. Note: There are
two levels of holes. Use the holes that match your application best.
Align the pin holes and insert clevis pins
F
into each of the pin
holes(4total).
3 – Installation (continued)
2
3
B
B
C
1
1
2
3
4
5
5
4
D
E
F
A
201105211 93-2973.indb 6 5/23/2011 12:56:47 PM
7
3-5 Installation Within Row (continued)
3-6 Ground Connection
After installing the SRCABLELADDER accessory, determine
where to place ground brackets by noting the distance between
one end of the ladder and the grounding post
A
at the corner of the
nearest SRCABLETRAY accessory.
Placeagroundbracket
B
near the end of the SRCABLELADDER
accessory’sleganduseahex-headbolt
C
to secure it.
Usetheincludedhexnutsandlockwashers
G
to connect one end
of the included ground cable
H
to a grounding post
I
at the corner
of the nearest SRCABLETRAY accessory and connect the other
end to the grounding post
J
of the ground bracket attached to the
SRCABLELADDERaccessory.Repeatsteps1to3fortheother
end of the SRCABLELADDER accessory.
After inserting the clevis pins, insert a cotter pin
G
through the
holeattheendofeachclevispin.(Thestraightsectionofthe
cotterpingoesthroughthehole.)
3 – Installation (continued)
1
6
2
3
G
6
A
1
2
3
B
C
G
G
H
I
J
201105211 93-2973.indb 7 5/23/2011 12:56:48 PM
8
4 – Storage and Service
5 – Warranty and Warranty Registration
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Storage
Theunitmustbestoredinaclean,secureenvironmentwithatemperaturelessthan40°C(104°F)andarelativehumiditylessthan90%
(non-condensing).Storetheunitinitsoriginalshippingcontainerifpossible.
Service
YourTrippLiteproductiscoveredbythewarrantydescribedinthismanual.AvarietyofExtendedWarrantyandOn-SiteServicePrograms
are also available from Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service,
follow these steps:
1.Reviewtheinstallationandoperationproceduresinthismanualtoinsurethattheserviceproblemdoesnotoriginatefromamisreadingofthe
instructions.
2.Iftheproblemcontinues,donotcontactorreturntheproducttothedealer.Instead,visitwww.tripplite.com/support.
3.Iftheproblemrequiresservice,visitwww.tripplite.com/supportandclicktheProductReturnslink.FromhereyoucanrequestaReturned
MaterialAuthorization(RMA)number,whichisrequiredforservice.Thissimpleon-lineformwillaskforyourunit’smodelandserial
numbers,alongwithothergeneralpurchaserinformation.TheRMAnumber,alongwithshippinginstructionswillbeemailedtoyou.Any
damages(direct,indirect,specialorconsequential)totheproductincurredduringshipmenttoTrippLiteoranauthorizedTrippLiteservice
centerisnotcoveredunderwarranty.ProductsshippedtoTrippLiteoranauthorizedTrippLiteservicecentermusthavetransportation
chargesprepaid.MarktheRMAnumberontheoutsideofthepackage.Iftheproductiswithinitswarrantyperiod,encloseacopyofyour
salesreceipt.ReturntheproductforserviceusinganinsuredcarriertotheaddressgiventoyouwhenyourequesttheRMA.
Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship
foraperiodof5yearsfromthedateofinitialpurchase.Iftheproductshouldprovedefectiveinmaterialorworkmanshipwithinthatperiod,
Seller will repair or replace the product, in its sole discretion.
THISWARRANTYDOESNOTAPPLYTONORMALWEARORTODAMAGERESULTINGFROMACCIDENT,MISUSE,ABUSE
ORNEGLECT.SELLERMAKESNOEXPRESSWARRANTIESOTHERTHANTHEWARRANTYEXPRESSLYSETFORTHHEREIN.
EXCEPTTOTHEEXTENTPROHIBITEDBYAPPLICABLELAW,ALLIMPLIEDWARRANTIES,INCLUDINGALLWARRANTIESOF
MERCHANTABILITYORFITNESS,ARELIMITEDINDURATIONTOTHEWARRANTYPERIODSETFORTHABOVE;ANDTHIS
WARRANTYEXPRESSLYEXCLUDESALLINCIDENTALANDCONSEQUENTIALDAMAGES.(Somestatesdonotallowlimitations
onhowlonganimpliedwarrantylasts,andsomestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sothe
abovelimitationsorexclusionsmaynotapplytoyou.ThisWarrantygivesyouspeciclegalrights,andyoumayhaveotherrightswhichvary
fromjurisdictiontojurisdiction.)
TrippLite;1111W.35thStreet;ChicagoIL60609;USA
WARNING:Theindividualusershouldtakecaretodeterminepriortousewhetherthisdeviceissuitable,adequateorsafefortheuseintended.
Sinceindividualapplicationsaresubjecttogreatvariation,themanufacturermakesnorepresentationorwarrantyastothesuitabilityortness
ofthesedevicesforanyspecicapplication.
Warranty Registration
Visitwww.tripplite.com/warrantytodaytoregisterthewarrantyforyournewTrippLiteproduct.You’llbeautomaticallyenteredintoadrawing
for a chance to win a FREE Tripp Lite product!*
*Nopurchasenecessary.Voidwhereprohibited.Somerestrictionsapply.Seewebsitefordetails.
TrippLitehasapolicyofcontinuousimprovement.Specicationsaresubjecttochangewithoutnotice.
201105211 • 932973-EN
201105211 93-2973.indb 8 5/23/2011 12:56:48 PM
9
Manual del propietario
Accesorios SmartRack
Modelo: SRCABLELADDER
1 – Introducción 10
1-2 Herramientas requeridas 10
3 – Instalación 11
3-2 Modificación de la escalera (Opcional) 12
3-4 Instalación en pasillo 13
3-6 Conexión a tierra 15
1-1 Lista de piezas 10
2 – Instrucciones de seguridad importantes 10
3-1 Planificación 11
3-3 Ensamblado de la escalera 12
3-5 Instalación en una fila 14
4 – Almacenamiento y servicio 16
5 – Garantía 16
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2011 Tripp Lite. Todas las otras marcas registradas son propiedad de sus respectivos dueños.
Français 17
English 1
201105211 93-2973.indb 9 5/23/2011 12:56:49 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Tripp Lite SRCABLELADDER Owner's manual

Category
Rack accessories
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI