American Standard 4332410F15.075 Installation guide
- Category
- Faucets
- Type
- Installation guide
This manual is also suitable for
SINGLE CONTROL PULL-DOWN
KITCHEN FAUCET
Installation
Instructions
M968517 REV.1.6 (7/15)
Certified to comply with ANSI A112.18.1M
CAUTION
1
INSTALL FITTING
Turn off hot and cold water
supplies before beginning.
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
Recommended Tools
Make certain the O-RING SEAL (1) is properly seated
in recess of faucet body.
Insert supply HOSES (2), SHANK (3) and SPRAY
HOSE (4) through center hole of sink or mounting
surface.
Assemble RUBBER WASHER (5), PLASTIC WASHER (6),
RUBBER & METAL “C” WASHERS (7) and long LOCKNUT (8)
onto SHANK (3) from underside of sink. Hand tighten
LOCKNUT (8) and check that faucet is centered.
Tighten LOCKNUT (8) with WRENCH (12) supplied. Insert
screwdriver into hole in WRENCH (12) and tighten.
Feed HOSE END (9) through HOSE GUIDE (10). Slide other
side of HOSE GUIDE (10) onto SHANK (3) and secure with
LOCK NUT (11). Do not over tighten!
Tubing Cutter
1
3
2
5
7
6
8
9
10
11
SCREWDRIVER
RECESS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
4
12
4332.310
4332.310F15
4332.410
4332.410F15
PEKOE
®
SINGLE CONTROL PULL-DOWN
BAR FAUCET
M968517 REV.1.6 (7/15)
RED
STRIPE
BLUE
STRIPE
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection
on fitting supplies are 3/8" compression. Connect left supply
(Marked with a Red Stripe) to Hot and right supply (Marked with
Blue Stripe) to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 27-1/2" long from faucet base.
Note: If additional supply length
is required, installer must
purchase additional parts
separately.
Important: If SUPPLY HOSES
(1, 2) are too long, loop as
illustrated to avoid kinking.
1
2
COLD
HOT
3
CONNECT HOSE SPRAY
and INSTALL WEIGHT
Figure 2
Check that seal washers are installed in both ends of SPRAY HOSE ADAPTER (1).
Thread SPRAY HOSE ADAPTER (1) onto faucet SHANK (2). Tighten with adjustable wrench.
Figure 1.
Thread HOSE END (3) into bottom of SPRAY HOSE ADAPTER (1). Tighten with adjustable wrench.
Make sure all connections are tight. Figure 1.
Install RUBBER BUSHING (4) onto SPRAY HOSE (5). Install WEIGHTS (6) onto HOSE (5) using two screws (7). Locate
WEIGHTS (6) 18" from underside of mounting surface on HOSE (5). Tighten SCREWS (5) firmly. Figure 2.
SEAL
WASHER
SEAL
WASHER
2
1
3
57
6
4
Figure 1
UNDER SIDE
OF MOUNTING
SURFACE
18"
9
8
11
3mm
HEX WRENCH
12
M968517 REV.1.6 (7/15)
4
TEST INSTALLED FAUCET
Unthread SPRAY HOSE (3) from SPRAY (2).
Turn on water supplies and check connections for leaks
.
Hold HOSE END (3) in sink and operate HANDLE (1) on and off,
hot and cold to flush water lines thoroughly. Replace SPRAY (2).
Pull SPRAY (2) out and check hose and supply connections
for leaks. Check that SPRAY HOSE (3) and WEIGHT (4) slide
up and down freely and do not interfear with supplies or waste
outlet plumbing. With faucet on push BUTTON (5) to spray. Move
HANDLE (1) to “off” position to return to aerator function.
Check all drain connections for leaks.
Move HANDLE (1) to "off" position.
1
2
5
3
3
4
Loosen and remove LEVER HANDLE (1). Loosen HANDLE
SCREW (2) with 2.5mm Hex Wrench and then pull HANDLE
BASE (3) off.
Unthread ESCUTCHEON CAP (4). Unthread the
CARTRIDGE NUT (5).
Remove CARTRIDGE (6). Clean inlets of CARTRIDGE (6)
and MANIFOLD (7).
Reassemble CARTRIDGE (6). Replace CARTRIDGE
NUT (5), CAP (4) and HANDLE assembly, check flow.
SERVICE
Clogged CARTRIDGE outlets or inlets may cause reduced
flow. To clean, first turn off water supply then:
5
6
HOT & COLD SUPPLIES
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
1
2
3
4
5
6
CLEAN
7
Move HANDLE (1) into "off" position.
If SPOUT (11) leaks at swivel point the O-RINGS (12) need
to be replaced. To remove SPOUT (11):
Disconnect SPRAY HOSE (8) from CONNECTING NUT (9).
Loosen the SPOUT SET SCREW (10) with a 3mm Hex wrench.
Rotate the SPOUT (11) side to side while pulling upward to
remove SPOUT (11) from faucet body. Remove SPRAY HOSE (8).
Replace the defective parts and grease O-RINGS (12). Replace SPRAY
HOSE (8). Push SPOUT (11) back into position. Tighten SET SCREW (10).
Reconnect SPRAY HOSE (8) to CONNECTING NUT (9).
Check that SPOUT (11) rotates freely and does not leak
at the swivel point.
REMOVE
INSTALL
10
M962648-0070A
SPOUT BUSHING
& O-RING KIT
M962648-0070A
SPOUT BUSHING
& O-RING KIT
MODEL NUMBER
M968517 REV.1.6 (7/15)
SINGLE CONTROL PULL-DOWN
KITCHEN AND BAR FAUCETS
M962690-0070A
CARTRIDGE NUT
M9629691-YYY0A
CARTRIDGE COVER
M964406-0070A
CARTRIDGE
M962755-YYY0A
HANDLE KIT
M962659-0070A
MOUNTING KIT
M962660-0070A
HOSE GUIDE
M962650-0070A
HOSE WEIGHTS
M962661-0070A
NUT
M911764-0070A
SEAL WASHER
M962662-0070A
SPRAY HOSE ADAPTER
WITH CHECK VALVE
M962686-0070A
O-RING
M962704-YYY0A
PEDESTAL
M962758-YYY220A
(2.2 GPM)
PULL-OUT SPRAY
WITH CHECK VALVE
M962758-YYY150A
(1.5 GPM)
PULL-OUT SPRAY
WITH CHECK VALVE
M962652-0070A
SPOUT SET SCREW
M962760-YYY0A
SPOUT ASSEMBLY
(4332.310)
M962761-YYY0A
SPOUT ASSEMBLY
(4332.410)
M964448-0020A
NYLON SPRAY HOSE
AND SEALS
STAINLESS STEEL 075
CHROME 002
Replace the "YYY" with
appropriate finish code
PEKOE
®
4332.310
4332.310F15
4332.410
4332.410F15
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
IN MEXICO 01-800-839-12-00
-
1
-
2
-
3
-
4
American Standard 4332410F15.075 Installation guide
- Category
- Faucets
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard M968414 User manual
-
-
-
-
-
-
-
American Standard 4433350.002 Installation guide
-
-