EarthQuake ECS6D Owner's manual

Brand
EarthQuake
Model
ECS6D
Category
Loudspeakers
Type
Owner's manual

This manual is also suitable for

Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545
Phone: 510-732-1000 Fax: 510-732-1095
ECS
The Sound That Will Move You
The Sound That Will Move You
Edgeless High Fidelity
In-Ceiling Speaker Series
Installation Manual
www. sound.comearthquake
ECS6.5 & ECS8.0
ECS6D & ECS8D
www.earthquakesound.com
3
Thank you for purchasing the ECS, Edgeless Series of In-Ceiling Speakers; one
of Earthquake Sound's most valued in-Ceilingl speaker lines. Designed with
aesthetics and sound quality in mind, the ECS seamlessly blends into its
surrounding as it provides a lifetime of durability and high-end performance.
It is very important to read and follow all installation/mounting instructions and
recommendations in this manual thoroughly to ensure optimal performance and
longevity.
Dear Valued Customer,
WARNING: These products are
capable of generating high
sound pressure levels. You
should exercise caution when
operating these speakers. Long
term exposures to high levels of
sound pressure will cause permanent damage
to your hearing. Sound pressure levels
exceeding 85dB can be dangerous with
constant exposure, set your audio system to a
comfortable loudness level. Earthquake
Sound Corporation does not assume liability
for damages resulting from the direct use of
Earthquake speakers , and urges users to play
volume at moderate levels.
Customer Support
[email protected]
Tel: 800-576-7944
Fax: 510-732-1095
Earthquake Sound Corporation
2727 McCone Avenue
Hayward, CA 94545
Tel: 510-732-1000
Fax: 510-732-1095
The Sound That Will Move You
S O U N D
The Sound That Will Move You
S O U N D
© 2013 Earthquake Sound Corporation. All rights reserved.
This document should not be construed as a commitment on the part of Earthquake Sound
Corporation. The information is subject to change without notice. Earthquake Sound Corporation
assumes no responsibility for errors that may appear within this document.
Calls attention to a procedure,
practice, condition or the like that, if
not correctly performed or adhered to,
could result in injury or death.
Calls attention to a procedure,
practice, condition or the like that, if
not correctly performed or adhered to,
could result in damage to or
destruction of part or all of the product.
Specifications are subject to change without notice
4
www.earthquakesound.com
5
ECSD Features & FunctionsECS Features & Functions
ECS6.5 & ECS8.0
The ECS Features
» Frameless design for reduced visibility/low profile/seamless blend
» Long excursion kevlar woofer cones
» One 1” (25mm) silk dome NEO swiveling tweeter
» ± 3dB bass and treble controls
» Elaborate crossover networks with polyswitch protection
» Easy Turn-N-Lock™ installation mechanism
» Gold plated, spring loaded terminals
» Magnetically attached, paintable grilles
The ECSD Features
» Frameless design for reduced visibility/low profile/seamless blend
» Long excursion kevlar woofer cones
» Two 1” (25mm) silk dome NEO swiveling tweeters
» Dual voice coil woofer
» ± 3dB bass and treble controls
» Dipole / Bipole modes
» Surround / DVC modes
» Elaborate crossover networks with polyswitch protection
» Easy Turn-N-Lock™ installation mechanism
» Gold plated, spring loaded terminals
» Magnetically attached, paintable grilles
ECS6D & ECS8D
The Edgeless In-Ceiling Dual speakers are designed for use in limited/small
spaces like bathrooms, kitchens, corridors, etc... They feature dual tweeters
and dual woofer voice coils (2 speakers in 1): one ECSD is capable of
reproducing a stereo signal; thus eliminating the need to use two speakers.
The Edgeless In-Ceiling speakers are designed for use in any space like
bedrooms, living rooms, kitchens, etc... Each features a single 1” Neo tweeter
and a long excursion woofer. The ECS seamlessly blend into surrounding as
they provide a lifetime of durability and high-end performance.
Specifications are subject to change without notice
6
www.earthquakesound.com
7
ECS6D Settings & OptionsECS6D Settings & Options
Bipole Dipole
High Definition Stereo application using one (1) ECS6D:
- Set switch #1 in Dipole mode
- Set switch #2 in DVC mode
- Impedance 8-Ohm per terminal
- Connect both terminals A & B separately (2 separate inputs / left & right)
Surround Effect Stereo application using one (1) ECS6D:
- Set switch #1 in Dipole mode
- Set switch #2 in Surround mode
- Impedance 8-Ohm per terminal
- Connect both terminals A & B separately (2 separate inputs / left & right)
Bipole Dipole
Surround DVC
Mono application using one (1) ECS6D:
- Set switch #1 in Bipole mode
- Set switch #2 in DVC mode
- Total impedance 4-Ohm
- Connect one (1) terminal A OR B (1 input)
Surround Effect Mono application using one (1) ECS6D:
- Set switch #1 in Bipole mode
- Set switch #2 in Surround mode
- Total impedance 4-Ohm
- Connect one (1) terminal A OR B (1 input)
#1
Bipole Dipole
Surround DVC
#1
#2
#2
Bipole Dipole
Surround DVC
#1
#2
Bipole Dipole
Surround DVC
#1
#2
Bipole Dipole
1/2 = 8-Ohm
&
3/4 = 8-Ohm
1/2 = 8-Ohm
&
3/4 = 8-Ohm
1/2 = 8-Ohm
&
3/4 = 8-Ohm
Surround DVC
1
_ _
+
+
2
3
4
Terminal A Terminal B
1
_ _
+
+
2
3
4
Terminal A Terminal B
(connect both terminals A & B)
(connect both terminals A & B)
1
_ _
+
+
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
1
_ _
+
+
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
1
_ _
+
+
2
3
4
Terminal A Terminal B
(connect both terminals A & B)
1
_ _
+
+
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
The ECS6D is equipped with two (2) switches: the Bipole/Dipole switch and the
Surround/DVC switch. The two switches work independently, they are used to
customize the ECS6D performance for different applications.
In Dipole mode, the speaker is in STEREO mode (2 speakers in 1). The two
terminals are totally independent (2 separate inputs, using both terminals).
Each terminal has an impedance of 8-Ohm. The speaker can be set in Surround
or in DVC mode depending on the listener preferences. In Bipole mode, the
speaker is in MONO mode. The two terminals are internally connected in
parallel (1 input needed, using only one terminal). The total speaker impedance
is 4-Ohm. Again, he speaker can be set in Surround or in DVC mode depending
on the listener preferences.
In DVC mode, the speaker exhibits higher level of details & separation between
L & R channels. The Surround mode gives the speaker response more
surround feeling, deeper warmer bass & more blending between L & R
channels.
Specifications are subject to change without notice
8
www.earthquakesound.com
9
ECS8D Settings & Options
High Definition Stereo application using one (1) ECS8D:
- Set switch #1 in Dipole mode
- Set switch #2 in DVC mode
- Impedance 8-Ohm per terminal
- Connect both terminals A & B separately (2 separate inputs / left & right)
Surround Effect Stereo application using one (1) ECS8D:
- Set switch #1 in Dipole mode
- Set switch #2 in Surround mode
- Impedance 8-Ohm per terminal
- Connect both terminals A & B separately (2 separate inputs / left & right)
Bipole Dipole
Surround DVC
Mono application using one (1) ECS8D:
- Set switch #1 in Bipole mode
- Set switch #2 in DVC mode
- Total impedance 4-Ohm
- Connect one (1) terminal A OR B (1 input)
Surround Effect Mono application using one (1) ECS8D:
- Set switch #1 in Bipole mode
- Set switch #2 in Surround mode
- Total impedance 4-Ohm
- Connect one (1) terminal A OR B(1 input)
#1
Bipole Dipole
Surround DVC
#1
#2
#2
Bipole Dipole
Surround DVC
#1
#2
Bipole Dipole
Surround DVC
#1
#2
ECS8D Settings & Options
1/2 = 8-Ohm
&
3/4 = 8-Ohm
1/2 = 8-Ohm
&
3/4 = 8-Ohm
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect both terminals A & B)
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect both terminals A & B)
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
Bipole Dipole
Bipole Dipole
1/2 = 8-Ohm
&
3/4 = 8-Ohm
Surround DVC
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect one terminal A or B)
1
_ _
+ +
2
3
4
Terminal A Terminal B
(connect both terminals A & B)
The ECS8D is equipped with two (2) switches: the Bipole/Dipole switch and the
Surround/DVC switch. The two switches work independently, they are used to
customize the ECS6D performance for different applications.
In Dipole mode, the speaker is in STEREO mode (2 speakers in 1). The two
terminals are totally independent (2 separate inputs, using both terminals).
Each terminal has an impedance of 8-Ohm. The speaker can be set in Surround
or in DVC mode depending on the listener preferences. In Bipole mode, the
speaker is in MONO mode. The two terminals are internally connected in
parallel (1 input needed, using only one terminal). The total speaker impedance
is 4-Ohm. Again, he speaker can be set in Surround or in DVC mode depending
on the listener preferences.
In DVC mode, the speaker exhibits higher level of details & separation between
L & R channels. The Surround mode gives the speaker response more
surround feeling, deeper warmer bass & more blending between L & R
channels.
Specifications are subject to change without notice
10
www.earthquakesound.com
11
Simply tighten the screws by hand using a
screwdriver to prevent the mounting ears
from snapping. Some resistance may occur
the first few turns of the screw as it makes its
path through the plastic.
Easy Installation Steps
1
Cut the hole:
using the provided
cut out template
2
Wire the speaker:
using the non-obtrusive
spring-loaded speaker
terminals
3
Mount the speaker:
by utilizing the
Turn-N-Lock™
installation mechanisms
Placement Considerations
Speaker Placement
The ECS Edgeless In-Ceiling Speakers are designed to be flush mounted in
walls or ceilings. For optimal acoustical performance, simply follow these
guidelines:
1. Place speakers at an equal distance (left/right) from listener.
2. Speakers must be spaced at a 40 - 60° angle from listener (Figure 1).
3. Aim tweeter towards the listener’s ear when in listening position.
Figure 1
40 - 60°
TREBLE
BASS
0
+3
-3
0
+3
-3
TREBLE
BASS
0
+3
-3
0
+3
-3
Grille Painting Guidelines
The ECS Edgeless In-Ceilingl Speaker grilles are paintable and can accept
virtually any type of paint. We strongly recommend the following:
1. Remove the grilles from the speakers prior to painting them.
2. Thin the paint prior to application, if needed. Spray and roller paint
applications typically provide the best results. Note that you may need to
apply multiple thin layers of paint to achieve the desired shade without
losing sound quality due to clogging of the grilles.
3. Let the painted grilles fully dry before mounting them back on the
speakers.
Specifications
Specifications
www.earthquakesound.com
Specifications are subject to change without notice
12 13
E C S 6.5 S P E C IFICAT I O N S
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
40Hz - 20kHz
87dB @ 1W/1M
8-Ohm
300 Watts Max
Impact resist ABS Plastic
Grille Finish: White / Paintable
Mounting Depth: 4 5/16” (110mm)
Cut Out Diameter:
7 7/8” (200mm)
Outer Diameter:
8 9/16” (223mm)
Two-way system using:
one 6.5” low mass stiff kevlar
cone midbass and one 1” silk
dome swiveling NEO tweeter
Wire Gauge Recommended:
12
Weight Per Speaker:
3.9 lbs
E C S 8.0 S P E C IFICAT I O N S
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
30Hz - 20kHz
88dB @ 1W/1M
8-Ohm
400 Watts Max
Impact resist ABS plastic
Two-way system using:
one 8” low mass stiff kevlar
cone midbass and one 1” silk
dome swiveling NEO tweeter
Grille Finish: White / Paintable
Wire Gauge Recommended:
Weight Per Speaker:
12
4.3 lbs
Mounting Depth:
4 7/8” (124mm)
Outer Diameter:
Cut Out Diameter:
9 1/2” (242mm)
10 1/2” (267mm)
4 7/8” (124mm)
Ø 10 1/2” (267mm)
Ø 9 1/2” (242mm)
4 5/16” (110mm)
Ø 8 9/16” (223mm)
Ø 7 7/8” (200mm)
Specifications
Specifications
www.earthquakesound.com
Specifications are subject to change without notice
14 15
E C S 6D SP E C I FICATIONS
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
40Hz - 20kHz
87dB @ 1W/1M
8-Ohm In Dipole Mode
4-Ohm In Bipole Mode
8-Ohm In Dipole Mode
4-Ohm In Bipole Mode
350 Watts Max
Impact resist ABS Plastic
Grille Finish: White / Paintable
Mounting Depth: 4 5/16” (110mm)
Cut Out Diameter:
7 7/8” (200mm)
Outer Diameter:
8 9/16” (223mm)
Two-way system using:
one 6.5” low mass stiff kevlar
cone midbass and two 1” silk
dome swiveling NEO tweeters
Wire Gauge Recommended:
12
Weight Per Speaker:
4 lbs
E C S 8D SP E C I FICATIONS
Frequency Response:
Sensitivity:
Nominal Impedance:
Power Handling:
Enclosure Material / Type:
Driver Components:
30Hz - 20kHz
88dB @ 1W/1M
450 Watts Max
Impact resist ABS plastic
Two-way system using:
one 8” low mass stiff kevlar
cone midbass and two 1” silk
dome swiveling NEO tweeters
Grille Finish: White / Paintable
Wire Gauge Recommended:
Weight Per Speaker:
12
4.5 lbs
Mounting Depth:
4 7/8” (124mm)
Outer Diameter:
Cut Out Diameter:
9 1/2” (242mm)
10 1/2” (267mm)
4 5/16” (110mm)
Ø 8 9/16” (223mm)
Ø 7 7/8” (200mm)
4 7/8” (124mm)
Ø 10 1/2” (267mm)
Ø 9 1/2” (242mm)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

EarthQuake ECS6D Owner's manual

Brand
EarthQuake
Model
ECS6D
Category
Loudspeakers
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents