Heat & Glo LifeStyle 6000ARCH User manual

1

- Do not store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any other appliance.

- What to do if you smell gas

 Do not try to light any appliance.

 Do not touch any electrical switch.

 Do not use any phone in your building.

 Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

 If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Heat-N-Glo

Models:

6000TR

6000XLT-CDN

6000ARCH

6000XLS

Installers Guide

WARNING: IMPROPER INSTALLA-

TION, ADJUSTMENT, ALTERATION,

SERVICE OR MAINTENANCE CAN

CAUSE INJURY OR PROPERTY DAM-

AGE. REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL INFOR-

MATION CONSULT A QUALIFIED IN-

STALLER, SERVICE AGENCY, OR THE

GAS SUPPLIER.

525-983C 1/00

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THIS APPLIANCE. THIS INSTALL-

ERS GUIDE MUST BE LEFT WITH THE APPLI-

ANCE FOR FUTURE REFERENCE.

1. This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home, where not

prohibited by local codes.

2.This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases, unless a certified kit is

used.

Please contact your Heat-N-Glo dealer for any

questions or concerns. For the number of your

nearest

Heat-N-Glo dealer, please call 612-985-6000.

Heat-N-Glo, a division of Hearth Technologies Inc.

20802 Kensington Boulevard, Lakeville, Mn 55044

WARNING: IF THE INFORMATION

IN THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE OR

EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

Underwriters

Laboratories Listed

1

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;

4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)

543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.

2

!

SAFETY AND WARNING INFORMATION

READ and UNDERSTAND all instructions carefully before starting the installation.

FAILURE TO FOLLOW these installation instructions may result in a possible fire

hazard and will void the warranty.

Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the

Owners Guide.

DO NOT USE this appliance if any part has been under water. Immediately CALL a

qualified service technician to inspect the unit and to replace any part of the control

system and any gas control which has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a qualified service person. The

appliance and venting system should be INSPECTED before initial use and at least

annually by a professional service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc. It is IMPERATIVE that the units

control compartment, burners, and circulating air passageways BE KEPT CLEAN to

provide for adequate combustion and ventilation air.

Always KEEP the appliance clear and free from combustible materials, gasoline, and

other flammable vapors and liquids.

NEVER OBSTRUCT the flow of combustion and ventilation air. Keep the front of the

appliance CLEAR of all obstacles and materials for servicing and proper operations.

Due to the high temperature, the appliance should be LOCATED out of traffic areas

and away from furniture and draperies. Clothing or flammable material SHOULD NOT

BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature

and should STAY AWAY to avoid burns or clothing ignition. Young children should be

CAREFULLY SUPERVISED when they are in the same room as the appliance.

These units MUST use one of the vent systems described in the Installing the Fireplace

section of the Installers Guide. NO OTHER vent systems or components MAY BE USED.

This gas fireplace and vent assembly MUST be vented directly to the outside and

MUST NEVER be attached to a chimney serving a separate solid fuel burning

appliance. Each gas appliance MUST USE a separate vent system. Common vent

systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to make sure that no debris is

interfering with the air flow.

The glass door assembly MUST be in place and sealed, and the trim door assembly

MUST be in place on the fireplace before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door removed, cracked, or broken.

Replacement of the glass door should be performed by a licensed or qualified service

person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced as a complete unit, as supplied

by the gas fireplace manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door assembly. DO NOT ATTEMPT to

clean the glass door when it is hot.

Turn off the gas before servicing this appliance. It is recommended that a qualified

service technician perform an appliance check-up at the beginning of each heating

season.

Any safety screen or guard removed for servicing must be replaced before operating

this appliance.

3

TABLE

OF

CONTENTS

Safety and Warning Information ......................... 2

Section 1: Approvals and Codes ...................... 4

Approval Listings and Codes ................................... 4

Appliance Certification ............................................. 4

Installation Codes .................................................... 4

High Altitude Installations .......................................... 4

Section 2: Getting Started ................................ 5

Introducing the Heat-N-Glo Gas Fireplaces .............. 5

Pre-installation Preparation...................................... 5

Section 3: Installing the Fireplace .................... 8

Step 1 Locating the Fireplace ............................... 8

Step 2 Framing the Fireplace ............................... 9

Step 3 Installing the Vent System ........................ 10

A. Vent System Approvals ........................ 10

B. Installing Vent Components ................. 20

C. Vent Termination ................................. 26

Step 4 Positioning, Leveling, and

Securing the Fireplace ............................. 31

Step 5 The Gas Control Systems ....................... 31

Step 6 The Gas Supply Line ............................... 32

Step 7 Gas Pressure Requirements................... 33

Step 8 Wiring the Fireplace ................................ 34

Step 9 Finishing ................................................. 36

Step 10 Installing Trim, Logs, and

Ember Material ........................................ 37

Installing the Trim ..................................... 37

Positioning the Logs ................................ 38

Placing the Ember Material ...................... 38

Step 11 Before Lighting the Fireplace .................... 40

Step 12 Lighting the Fireplace ............................... 40

Step 13 Heating Control - 6000XLT-CDN .............. 41

Step 14 Relief Ports - 6000ARCH ......................... 41

After the Installation ............................................... 41

Section 4: Maintenance and Servicing .......... 42

Section 5: Replacement Parts

and Accessories ................................................. 44

Replacement Parts ............................................... 44

Accessories ......................................................... 48

4

Approval Listings

and Codes

Appliance Certification

The Heat-N-Glo models discussed in this Installers

Guide have been tested to certification standards

and listed by the applicable laboratories.

CERTIFICATION

MODEL LABORATORY TYPE STANDARD

6000TR & Underwriters Vented Gas

ANSI Z21.50 CGA2.22/IR#41

6000ARCH Laboratories Fireplace

6000XLT-CDN Underwriters Vented Gas Fireplace ANSI Z21.50 CGA2.22

Laboratories & Vented Gas ANSI Z21.88 CSA2.33

Fireplace Heater

6000XLS Underwriters Vented Gas ANSI Z21.88 CSA2.33

Fireplace Heater

Installation Codes

The fireplace installation must conform to local codes. Before installing the

fireplace, consult the local building code agency to ensure that you are in

compliance with all applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must conform to the

National Fuel Gas Code ANSI Z223.1 (in the United States) or the CAN/CGA-

B149 Installation Codes (in Canada). The appliance must be electrically

grounded in accordance with local codes or, in the absence of local codes

with the National Electric Code ANSI/NFPA No. 70 (in the United States), or to

the CSA C22.1 Canadian Electric Code (in Canada).

These models may be installed in a bedroom or bed-sitting room in the U.S.A.

and Canada.

High Altitude Installations

U.L. Listed gas fireplaces are tested and approved for elevations from 0 to

2,000 feet in the U.S.A. and from 0 to 4,500 feet in Canada.

When installing this fireplace at an elevation above 2,000 feet (in the United

States), it may be necessary to decrease the input rating by changing the

existing burner orifice to a smaller size. Input should be reduced four percent

(4%) for each 1,000 feet above sea level, unless the heating value of the gas

has been reduced, in which case this general rule will not apply. To identify the

proper orifice size, check with the local gas utility.

When installing this fireplace at an elevation between 2,000 and 4,500 feet (in

Canada), the input rating must be reduced by ten percent (10%).

When installing this fireplace at an elevation above 4,500 feet (in Canada),

check with local authorities.

Consult your local gas utility for assistance in determining the proper orifice for

your location.

1

Approvals

and Codes

5

2

Getting

Started

Heat-N-Glo direct vent gas fireplaces are designed to

operate with all combustion air siphoned from outside

of the building and all exhaust gases expelled to the

outside.

The information contained in this Installers Guide,

unless noted otherwise, applies to all models and

gas control systems.

Gas fireplace diagrams, including the dimensions,

are shown in this section.

This gas fireplace and its components are tested

and safe when installed in accordance with this

Installers Guide. Report to your dealer any parts

damaged in shipment, particularly the condition of

the glass. Do not install any unit with damaged,

incomplete, or substitute parts.

NOTE: FOR MODEL 6000TR ONLY:

These fireplaces are shipped from the factory with a

BTU rating of 27,000 BTUs. The fireplace can be

installed with the vent pipe coming off the top of the

unit or the rear of the unit. If you install the unit with

the vent pipe coming off the top of the unit, you may

run the unit at 31,000 BTU (NG) (30,000 BTU LP),

replace the burner orifice with the orifice included in

the manual bag. DO NOT REPLACE THE ORIFICE

IF YOU ARE USING THE REAR SET OF VENT

COLLARS.

Changing the orifice when venting out the top.

1. Remove the glass door.

2. Using a 1/4 socket, remove the sheetmetal

screws holding the long refractory clip in place.

Remove the logs and refractory as one piece.

3. Remove the protective plastic from the logs.

4. Remove the two sheetmetal screws holding the

burner and remove the burner.

5. Replace the burner orifice with the orifice in-

cluded in the plastic manual bag (#36DMS for

natural gas or #51DMS for propane). Be careful

to hold the brass elbow so you dont kink the

aluminum tube.

6. Reverse the steps to replace the burner, logs,

refractory, and clip.

The vent system components and trim doors are

shipped in separate packages. The gas logs may

be packaged separately and must be field installed.

Read all of the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum

safety and benefit. Failure to follow these

instructions will void the owners warranty and

may present a fire hazard.

Introducing the

Heat-N-Glo

Gas Fireplaces

Pre-install

Preparation

6

Figure 1. Diagram of the 6000TR, 6000XLT-CDN and 6000XLS

The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims any

responsibility for, the following actions:

 Installation of any damaged fireplace or vent system component.

 Modification of the fireplace or direct vent system.

 Installation other than as instructed by Heat-N-Glo.

 Improper positioning of the gas logs or the glass door.

 Installation and/or use of any component part not manufactured and approved by

Heat-N-Glo, not withstanding any independent testing laboratory or other party

approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, its necessary to determine:

 Where the unit is to be installed.

 The vent system configuration to be used.

 Gas supply piping.

 Electrical wiring.

 Framing and finishing details.

 Whether optional accessoriesdevices such as a fan, wall switch, or remote

controlare desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible

material other than wood flooring, the fireplace should be installed on a metal or

wood panel that extends the full width and depth of the fireplace.

Left Side Front Right Side

NOTE:

6000TR has top and rear collars.

6000XLT-CDN has top collars only.

6000XLS has rear collars only.

7

Figure 2. Diagram of the 6000ARCH

8

3

Installing the

Fireplace

Step 1

Locating the

Fireplace

The diagram below shows space and clearance

requirements for locating a fireplace within a room.

MODEL A B C D E

6000TR &

42 22 37 1/8 52 1/2 74 1/4

6000XLS

6000XLT-CDN 42 22 35 1/4 49 3/4 70 3/8

6000ARCH 42* 22 35 1/4 49 3/4 70 3/8

48 1/4

**

* SURROUND IN FRONT OF FINISHED WALL

** SURROUND FLUSH WITH FINISHED WALL.

NOTE: DIMENSIONS SHOWN IN INCHES.

Figure 3. Fireplace Dimensions, Locations, and

Space Requirements

Clearance Requirements

The top, back, and sides of the fireplace are defined

by stand-offs.

Minimum Clearances from the Fireplace to

Combustible Materials

Glass Rear of Sides of Top of

Front Floor Fireplace Fireplace Fireplace Ceiling

36 inches 0 1/2 inch 1/2 inch 3-1/2 inches 31 inches

(914 mm) (13 mm) (13 mm) (89 mm) (787 mm)

The minimum clearance to a perpendicular wall extend-

ing past the face of the fireplace is one inch (25 mm).

The back of the fireplace may be recessed 21 1/2

inches (546 mm) into combustible construction.

9

A

B

C

Framing should be

constructed of 2 X 4

lumber or heavier.

Model A B C D E

6000TR 42 38 1/4 22 42 26 1/4

6000XLS 42 38 1/4 22 N/A 26 1/4

6000XLT-CDN 42 38 1/4 22 42 N/A

6000ARCH 42* 41 7/8 22 53 5/8 N/A

48 1/4

**

* SURROUND IN FRONT OF FINISHED WALL

** SURROUND FLUSH WITH FINISHED WALL

NOTE: DIMENSIONS SHOWN IN INCHES

D

E

SHOWS CENTER OF12" X 12"

VENT FRAMING HOLES FOR

TOP & REAR VENTING.

Figure 4. Framing Dimensions

Minimum Clearances from the Vent Pipe to

Combustible Materials

For Vertical

For Horizontal Sections Sections At Wall Firestops

Top Bottom Sides Top Bottom Sides

3 inches 1 inch 1 inch 1 inch 2-1/2 inches 1/2 inch 1 inch

(75 mm) (25 mm) (25 mm) (25 mm) (63.7 mm) (13 mm) (25 mm)

For minimum clearances, see the direct vent

termination clearance diagrams on pages 28 and 30 in

this manual.

Step 2

Framing the

Fireplace

Fireplace framing can be built before or after the

fireplace is set in place. Framing should be positioned

to accommodate wall coverings and fireplace facing

material. The diagram below shows framing reference

dimensions.

CAUTION

MEASURE FIREPLACE DIMENSIONS, AND

VERIFY FRAMING METHODS AND WALL

COVERING DETAILS, BEFORE FRAMING

CONSTRUCTION BEGINS.

10

VENT SYSTEM

TERMINATION KITS

VENT SYSTEM COMPONENTS

Figure 5. Vent Components and Terminations

Step 3

Installing the

Vent System

A. Vent System Approvals

These models are approved to use D-series direct vent

pipe components and terminations. Approved vent

system components are labeled for identification. NO

OTHER VENTING SYSTEMS OR COMPONENTS

MAY BE USED. Detailed installation instructions are

included with each vent termination kit and should be

used in conjunction with this Installers Guide. The

drawing below shows vent system components and

terminations.

The flame and ember appearance may vary based on the

type of fuel burned and the venting configuration used.

Identifying Vent Components

The vent systems installed on this gas fireplace may

include one, two, or three 90°

elbow assemblies. The

relationships of vertical rise to horizontal run in vent

configurations using 90° elbows MUST BE strictly

adhered to. The rise to run relationships are shown in

the venting drawings and tables. Refer to the diagrams

on the next several pages.

NOTE: TWO 45° ELBOWS MAY BE USED IN PLACE

OF ONE 90° ELBOW. RISE TO RUN RATIOS IN THE

VENT SYSTEM MUST BE FOLLOWED IF 45°

ELBOWS ARE USED.

This model has vent starting collars on both the top and

the back of the unit. Depending upon the installation,

decide which ONE set of starting collars will be used to

attach the vent system. The starting collar sealing cap

must remain on the starting collar NOT used.

11

DV-90D

65/32

57/873/8

DV-45D

67/16

11 1/16

61/2

85/8

81/2

51/16

8/12

11 5/8

85/8

11 15/16

DV-36D

35 3/4

47 3/4

DV-48D

5 3/4

8 3/4

11 3/4

DV-12D

DV-09D

DV-06D

6-5/32"

(156 mm)

7-3/8" 5-7/8"

(187 mm) (149 mm)

8-1/2"

(216 mm)

8-5/8"

(220 mm)

11-15/16"

(303 mm)

11-5/8"

(295 mm)

11-1/16"

(281 mm)

6-1/2"

(165 mm)

8-5/8"

(220 mm)

5-1/16"

(129 mm)

8-1/2"

(216 mm)

6-7/16"

(164 mm)

35-3/4"

(908 mm)

47-3/4"

(1.2 m)

11-3/4"

(298 mm)

8-3/4"

(222 mm)

5-3/4"

(146 mm)

NOTE: PIPES OVERLAP 1-3/8 INCHES (34.93 mm) AT EACH JOINT.

Figure 6. D-Series Direct Vent Component Specifications

(5-inch inner pipe/ 8 5/8-inch outer pipe)

12

Figure 7. Straight Up Vertical Venting

STRAIGHT UP

VERTICAL VENTING

V (FT.)

40' MAX. (12.4 M)

NOTE: Model 6000ARCH

A 12-inch length of straight vent

pipe MUST be the first vent

component attached to the unit.

13

HORIZONTAL VENTING

H

Kit No. Max. Run

DVK-01D

DVK-01TRD 24" (610 mm)

NOTE: Models 6000TR and 6000XLS are tested and approved to

use 45° elbows in corner installations. However, 90° elbows will result

in better performance.

Figure 8. Corner Installation

14

VENTING WITH ONE (1) 90° ELBOW

V (FT.) H (FT.)

1' MIN. (305mm) 2' MAX. (610mm)

2' MIN. (610mm) 4' MAX. (1.22m)

3' MIN. (914mm) 6' MAX. (1.86m)

4' MIN. (1.22m) 8' MAX. (2.4m)

H = 8' MAX. (2.4m)

V+H = 40' MAX. (12.4m)

Figure 9. Venting with One 90° Elbow

15

VENTING WITH ONE (1) 90° ELBOW

V (FT.) H (FT.)

1' MIN. (305mm) 5' MAX. (1.52m)

2' MIN. (610mm) 10' MAX. (3.1m)

3' MIN. (914mm) 15' MAX. (4.65m)

4' MIN. (1.22m) 20' MAX. (6.2m)

H = 20' MAX. (6.2m)

V + H = 40 MAX. (12.4mm)

Figure 10. Venting with One 90° Elbow

FOR 6000TR & 6000XLT-CDN

NOTE: If a 90

o

elbow is first at-

tached to the unit, the maximum

horizontal run is 3-feet (914mm).

NOTE: For corner installations: A 6-inch (152mm) MINIMUM length of straight

pipe must be attached to the fireplace before 90

o

elbow. This will allow the vent

pipe to clear the top standoffs.

NOTE: MODEL 6000ARCH

A 12-inch length of straight vent

pipe MUST be the first vent

component attached to the unit.

16

VENTING WITH TWO (2) 90° ELBOWS

V H H + H

1

1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52m)

2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1m)

3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65m)

4´ MIN. (1.22 m) 8´ MAX. (2.48 m) 20´ MAX. (6.2m)

V+H+H

1

= 40´ MAX. (12.4 m) H = 8´ MAX. (2.48 m) H+H

1

= 20´ MAX. (6.2m)

Figure 11. Venting with Two 90° Elbows

17

VENTING WITH TWO (2) 90

o

ELBOWS

V (FT.) H + H

1

(FT.)

1' MIN. (305mm) 5´ MAX. (1.52m)

2' MIN. (610mm) 10´ MAX. (3.1m)

3' MIN. (914mm) 15´ MAX. (4.65m)

4' MIN. (1.22m) 20´ MAX. (6.2m)

V+H+H

1

= 40' MAX.(12.4m) H+H

1

= 20´ MAX. (6.2m)

Figure 12. Venting with Two 90° Elbows

NOTE: MODEL

6000ARCH

A 12-inch length

of straight vent

pipe MUST be

the first vent

component

attached to

the unit.

VENTING WITH TWO (2) 90

o

ELBOWS

V (FT.) H (FT.)

1' MIN. (305mm) 5´ MAX. (1.52m)

2' MIN. (610mm) 10´ MAX. (3.1m)

3' MIN. (914mm) 15´ MAX. (4.65m)

4' MIN. (1.22m) 20´ MAX. (6.2m)

H = 20´ MAX. (6.2m)

V+V

1

+H

= 40' MAX.(12.4m)

18

1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52 m)

2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1 m)

3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65 m)

4´ MIN. (1.22 m) 8´ MAX. (2.48 m) 20´ MAX. (6.2 m)

V+H+H

1

+H

2

= 40´ MAX.(12.4 m) H=8´MAX.(2.48 m) H+H

1

+H

2

=20´ MAX. (6.2 m)

VENTING WITH THREE (3) 90° ELBOWS

V H H + H

1

+ H

2

1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52 m)

2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1 m)

3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65 m)

4´ MIN. (1.22 m) 8´ MAX. (2.48 m) 20´ MAX. (6.2 m)

V

1

+V+H+H

1

=40

´

MAX.(12.4m) H=8´MAX.(2.48m) H+H

1

=20´MAX.(6.2m)

VENTING WITH THREE (3) 90° ELBOWS

V H H + H

1

Figure 13. Venting with three 90° elbows

19

VENTING WITH THREE (3) 90° ELBOWS

V (FT.) H

(FT.)

1' MIN. (305mm) 5' MAX. (1.52m)

2' MIN. (610mm) 10' MAX. (3.1m)

3' MIN. (914mm) 15' MAX. (4.65m)

4' MIN. (1.22m) 20' MAX. (6.2m)

NOTE: H + H

1

= 20' MAX. (6.2m)

V + V

1

+ H + H

1

= 40' MAX. (12.4m)

VENTING WITH THREE (3) 90° ELBOWS

V (FT.) H + H

1

(FT.)

1' MIN.(305mm) 5' MAX. (1.52m)

2' MIN. (610mm) 10' MAX. (3.1m)

3' MIN. (914mm) 15' MAX. (4.65m)

4' MIN. (1.22m) 20' MAX. (6.2m)

H + H

1

= 20' MAX. (6.2m)

NOTE: V+V

1

+H+H

1

= 40' MAX. (12.4m)

Figure 14. Venting with three 90° elbows

NOTE: MODEL

6000ARCH

A 12-inch length of

straight vent pipe

MUST be the first

vent component at-

tached to the unit.

20

Figure 15 For Model 6000TR

B. Installing Vent Components

For Model 6000TR

After determining which set of starting collars will be used

(top or rear), follow venting instructions accordingly.

Venting Out the Rear Vent

Remove the installed rear seal cap from the rear starting

collars by cutting the strap at each end. (See Figure 15).

Follow the vent configuration tables accordingly.

Remove the insulation from the REAR five inch flue. Pull

the heat shield out from outside of the firebox.

WARNING: THE TOP HEAT SHIELD (INSIDE

THE FIREBOX) MUST REMAIN ATTACHED

IF THE VENT SYSTEM IS ATTACHED TO THE

REAR STARTING COLLARS. SEE FIGURE 15.

Venting Out the Top Vent

Remove the top vent collar seal cap and the two

pieces of insulation inside the top two starting

collars (See Figure 15). Next remove the glass door.

Remove the heat shield from inside the TOP five inch flue

from outside of the firebox.

You have to take the glass off again for positioning the logs

when the unit is finally installed in place and finished

around it. Reinstall the glass door. Attach vent system to

the top starting collars.

WARNING: FAILURE TO REMOVE INSULA-

TION IN THE SET OF COLLARS YOU

ARE

USING COULD CAUSE A FIRE.

WARNING: THE REAR VENT COLLAR SEAL

CAP MUST REMAIN ATTACHED TO THE

REAR VENT COLLARS IF THE VENT SYS-

TEM IS ATTACHED TO THE TOP STARTING

COLLARS. SEE FIGURE 15.

WARNING: YOU MUST LEAVE THE INSU-

LATION IN PLACE IN THE SET OF COL-

LARS YOU

ARE NOT USING.

!

Page is loading ...

Heat & Glo LifeStyle 6000ARCH User manual

This manual is also suitable for

Heat & Glo LifeStyle 6000ARCH User manual

Related papers

Other documents