ESAB Carbon Dioxide Heater Troubleshooting instruction

ESAB
Brand
ESAB
Model
Carbon Dioxide Heater
Type
Troubleshooting instruction
F-14-226
October, 1995
INSTRUCTIONS for INSTRUCTIONS for
F-14-226
October, 1995
CARBON DIOXIDE HEATER
P/N 950578
for Single Cylinder Service
CARBON DIOXIDE HEATER
P/N 950578
for Single Cylinder Service
SPECIFICATIONS
Connections ....................................................... CGA 320 (CO
2
) female x male
Max. Pressure .................................................................................... 3000 psig
Electrical .......................................120 VAC/120 Watts, Standard 3-prong plug
Max. Temperature (approx.)..................................................................... 160
o
F
Max. CO
2
Flow ....................................................................................... 180 cfh
Dimensions .......................................................................... 4-3/4" x 2" x 1-3/4"
Wrench Flats......................................................................................1-1/4" x 1"
l Designed to prevent regulator "freeze-up" and malfunction using high flow
rates of CO
2
.
l Installs between regulator and cylinder valve.
l Wrench flats to facilitate installation.
l "Potted" insulation imbeds and provides total protection to electrical compo-
nents.
l Non-metallic sheath insulates and reduces surface temperatures to prevent
possible burns.
l Thermostatically controlled to maintain safe operation temperature and de-
pendable CO
2
delivery.
l Requires standard 3-conductor (grounded) electrical cord of appropriate
length.
INSTALLATION & OPERATION
1. Be sure to read and understand all instructions packed with the CO
2
regula-
tor.
2. Install supplied washer (or gasket) in the inlet female nut of both the regula-
tor and the heater.
3. Connect the heater to the cylinder valve outlet, and then the regulator to the
heater. Tighten the connections firmly with wrenches.
4. When ready to operate, connect extension cord of appropriate length to the
heater and to a standard 120 volt AC grounded receptacle. Heater acti-
vates when extension cord is connected. Allow 5 - 10 minutes for heater to
warm-up before you start delivering the CO
2
.
5. When not operating, unplug the heater.
CAUTION: Allow the heater to cool before handling. The exposed metal
parts in particular may cause burns.
SPECIFICATIONS
Connections ....................................................... CGA 320 (CO
2
) female x male
Max. Pressure .................................................................................... 3000 psig
Electrical .......................................120 VAC/120 Watts, Standard 3-prong plug
Max. Temperature (approx.)......................................................................160
o
F
Max. CO
2
Flow ....................................................................................... 180 cfh
Dimensions .......................................................................... 4-3/4" x 2" x 1-3/4"
Wrench Flats......................................................................................1-1/4" x 1"
l Designed to prevent regulator "freeze-up" and malfunction using high flow
rates of CO
2
.
l Installs between regulator and cylinder valve.
l Wrench flats to facilitate installation.
l "Potted" insulation imbeds and provides total protection to electrical compo-
nents.
l Non-metallic sheath insulates and reduces surface temperatures to prevent
possible burns.
l Thermostatically controlled to maintain safe operation temperature and de-
pendable CO
2
delivery.
l Requires standard 3-conductor (grounded) electrical cord of appropriate
length.
INSTALLATION & OPERATION
1. Be sure to read and understand all instructions packed with the CO
2
regula-
tor.
2. Install supplied washer (or gasket) in the inlet female nut of both the regula-
tor and the heater.
3. Connect the heater to the cylinder valve outlet, and then the regulator to the
heater. Tighten the connections firmly with wrenches.
4. When ready to operate, connect extension cord of appropriate length to the
heater and to a standard 120 volt AC grounded receptacle. Heater acti-
vates when extension cord is connected. Allow 5 - 10 minutes for heater to
warm-up before you start delivering the CO
2
.
5. When not operating, unplug the heater.
CAUTION: Allow the heater to cool before handling. The exposed metal
parts in particular may cause burns.
F-14-226 10/95 1C Printed in U.S.A. F-14-226 10/95 1C Printed in U.S.A.
  • Page 1 1

ESAB Carbon Dioxide Heater Troubleshooting instruction

ESAB
Brand
ESAB
Model
Carbon Dioxide Heater
Type
Troubleshooting instruction
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents