Seachrome SHAFSL-185155-PWS-WT Installation guide

Brand: Seachrome

Model: SHAFSL-185155-PWS-WT

Type: Installation guide

INSTALLATION INSTRUCTIONS

Silhouette SlimLine

Tub/Shower Seat

LIFESTYLE & WELLNESS ®

LIFESTYLE & WELLNESS®

Patent Pending

Page 1

of 5

PLEASE READ THESE INSTALLATION INSTRUCTIONS THOROUGHLY PRIOR TO INSTALLING THIS SHOWER SEAT

IMPORTANT: THIS PRODUCT SHOULD ONLY BE INSTALLED BY QUALIFIED AND TRAINED PERSONNEL

FAILURE TO FOLLOW THESE INSTRUCTIONS COULD LEAD TO IMPROPER INSTALLATION OF THE TUB/SHOWER SEAT,

STRUCTURAL AND/OR WATER DAMAGE TO THE WALL AND IN-WALL SUPPORT STRUCTURES, AND/OR SERIOUS

BODILY INJURY IN USE. IN ADDITION, ALL WARRANTIES, EXPRESS OR IMPLIED, WILL BE NULL & VOID DUE TO

IMPROPER INSTALLATION OF THIS PRODUCT. THE MANUFACTURER DOES NOT ASSUME ANY LIABILITY FOR DAMAGE

RESULTING FROM SERVICES PERFORMED BY OTHERS, OR FAULTY INSTALLATION, MISUSE OR MISAPPLICATION OF

GOODS.

THIS PRODUCT IS DESIGNED TO MEET OR EXCEED ALL LOAD REQUIREMENTS ESTABLISHED IN THE FEDERAL

SPECIFICATION #WW-P-541/8b AT 250 POUNDS OF FORCE. THE PERFORMANCE OF THIS PRODUCT IS SIGNIFICANTLY

IMPACTED BY THE STRENGTH OF THE WALL TO WHICH IT IS ATTACHED.

TO ASSURE PROPER AND SAFE INSTALLATION, THIS TUB/SHOWER SEAT MUST BE INSTALLED INTO A MINIMUM 2”

THICK, SOLID WOOD, IN-WALL BACKING MATERIAL. MAKE CERTAIN IN-WALL BACKING COMPLIES WITH ALL LOCAL

BUILDING CODE REQUIREMENTS.

MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT IS 300 LBS. WHEN PROPERLY INSTALLED.

1. Remove the Silhouette SlimLine Tub/Shower Seat from the shipping carton.

INSTALLATION INSTRUCTIONS

Silhouette SlimLine

Tub/Shower Seat

LIFESTYLE & WELLNESS ®

LIFESTYLE & WELLNESS®

Patent Pending

Page 2

of 5

2. Locating the SlimLine Tub/Shower Seat in the desired position for Walk-in Showers and Tub Enclosures.

Diagram 1

Walk-in Shower

Diagram 2

Tub Enclosure

Remove and open the paper template from

the shipping carton.

Locate the area with 2” solid wood in-wall

backing. Determine desired seat height

(ADA requirements stipulate a seat height of

17” – 19” from the floor). Using the

template (supplied by manufacturer), align

hole centerlines with the in-wall backing.

Using a level (not provided) ensure the “Top

of Seat Mounting Bracket” line is level.

(See Diagram 4)

Tape the template into position on the

mounting surface.

When installing the seat in a tub enclosure,

place the tub/shower seat in the open

position (as shown in Diagrams 1 & 2)

against the template, prior to installation, to

ensure the bottom of the seat will clear the

tub dam. (See Diagram 2)

Using a pencil or suitable marker, it is

extremely important you mark the center of

each of the six (6) mounting holes precisely

on the mounting surface. (See Diagram 4)

INSTALLATION INSTRUCTIONS

Silhouette SlimLine

Tub/Shower Seat

LIFESTYLE & WELLNESS ®

LIFESTYLE & WELLNESS®

Patent Pending

Page 3

of 5

Proceed cautiously through the following steps in this installation process to avoid drilling into in-wall water supply lines.

3. Mounting the Silhouette SlimLine Tub/Shower Seat in Tiled Wall Enclosure.

All mounting points must fasten into structural wood backing, minimum 2” thickness.

Avoid electrical and/or plumbing behind the wall, and where possible drill through tile – not through grout.

Step #1

Drill through the tile only with a 1/4“ Carbide tile drill bit (not provided) at the six (6) locations marked on

the wall to create clearance holes, leaving a center point mark in the cement board backing to use as a guide

for Step #2.

Step #2

Use a power drill with a 3/16” Standard drill bit (not provided) and drill into the 2” thick solid wood backing

in the wall, using the center point guide marks created in Step #1. Fill the clearance holes on the mounting

surface with silicone to ensure a water-tight seal will be created at all mounting locations.

INSTALLATION INSTRUCTIONS

Silhouette SlimLine

Tub/Shower Seat

LIFESTYLE & WELLNESS ®

LIFESTYLE & WELLNESS®

Patent Pending

Page 4

of 5

Step #4

Using the (4) #14 Flat Head Phillips sheet metal screws (supplied by manufacturer), screw

hardware into Holes #2 & #3, as shown in Diagram 3.

Once all four (4) screws are in place, tighten all (4) screws.

Diagram 3

Step #3

Secure the Seat Mounting Bracket to the wall starting with the (2) #14 Flat Head Hex Drive

screws (supplied by manufacturer) and Hole #1 (Key-Hole), as shown in Diagram 3.

Screw the (2) #14 Flat Head Hex Drive screws into 2” Solid Wood In-Wall Backing in Hole #1

(Key-Hole) for both Seat Mounting Brackets, leaving @ 5/16” gap between the wall and the

head of screw.

Place both Seat Mounting Brackets on the installed hardware thru the Key-Hole slots and allow

the seat to drop into place.

The holes on the mounting surface created in Step #2

should now line up with Holes #2 and #3 on the Seat Mounting Brackets.

INSTALLATION INSTRUCTIONS

Silhouette SlimLine

Tub/Shower Seat

LIFESTYLE & WELLNESS ®

LIFESTYLE & WELLNESS®

Patent Pending

Page 5

of 5

Step #5

Tilt the Seat Bottom Panel at

an approximate 45° angle to

tighten the (2) #14 Flat Head

Hex Drive screws located in

Hole #1 (Key-Hole) on both

Seat Mounting Brackets from

the top of the seat, using the

L-Shaped Hex Drive Key

(supplied by manufacturer).

Diagram 4

NOTE:

The Seat Bottom Panel is attached to the aluminum frame at the factory using high-strength VHB tape.

Do NOT attempt to remove the Seat Bottom Panel from the seat frame as it may cause severe damage to the seat.

To ensure proper and safe installation, the Silhouette SlimLine seat should not shift in any direction on the mounting surface.

Hardware Provided: (4) #14 Flat Head Phillips sheet metal screws 2-1/2” length

(2) #14 Flat Head Hex Drive sheet metal screws 1-1/2” length

Tools Provided: Hex L-Key with Standard Tip

Tools Required: Marking pencil/pen, level, masking tape, power drill, 1/4” Carbide tile drill bits, 3/16” Standard drill

bit, #3 phillips driver, silicone.

THIS COMPLETES THE INSTALLATION OF THE SILHOUETTE SLIMLINE TUB/SHOWER SEAT

Seachrome SHAFSL-185155-PWS-WT Installation guide

Seachrome SHAFSL-185155-PWS-WT Installation guide

Seachrome SHAFSL-185155-PWS-WT Installation guide

Related papers

Other documents