DFI CMS630-W480E/Q470E Owner's manual

Brand: DFI

Model: CMS630-W480E/Q470E

Type: Owner's manual

This manual is also suitable for

CMS630

CMS630-W480E/Q470E

A-619-M-2120

ATX Industrial Motherboard

User’s Manual

2User's Manual | CMS630

This publication contains information that is protected by copyright. No part of it may be repro-

duced in any form or by any means or used to make any transformation/adaptation without the

prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions or

changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for com-

pliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

3User's Manual | CMS630

Table of Contents

Chapter 1 - Introduction................................................................................................................6

Specifications ......................................................................................................................... 6

Features .................................................................................................................................. 8

Block Diagram ........................................................................................................................9

Chapter 2 - Hardware Installation ................................................................................................8

Board Layout...........................................................................................................................8

System Memory ..................................................................................................................... 9

Installing the DIMM Module ...........................................................................................9

Removing the DIMM Module ........................................................................................10

CPU ........................................................................................................................................11

Installing the CPU Fan and Heat Sink .......................................................................... 11

Jumper Settings ...................................................................................................................12

CLEAR CMOS Data ........................................................................................................12

COM1/COM2 RS232/422/485 Select ..........................................................................13

COM1/COM2 RS232 Power Select ..............................................................................14

DIO Power & Voltage - JP11/12/13/14/15..................................................................15

AT/ATX Mode - JP26 .....................................................................................................15

PWM Control - JP23 ...................................................................................................... 16

InnoAGE HDR1 ............................................................................................................... 16

M2 Connector Power Control - M2JP1 / M2JP2 ........................................................17

Rear I/O Ports .......................................................................................................................18

USB Ports ....................................................................................................................... 19

Graphics Interfaces .......................................................................................................20

COM1 .............................................................................................................................. 20

RJ45 LAN Ports ............................................................................................................. 21

Audio .............................................................................................................................21

Internal I/O Connectors .......................................................................................................22

SATA (Serial ATA) ..........................................................................................................22

Digital I/O Connector .....................................................................................................22

COM (Serial) ports .........................................................................................................23

Cooling Fan Connectors ................................................................................................24

Power Connector ...........................................................................................................24

Front Panel .....................................................................................................................25

S/PDIF Connector .......................................................................................................... 25

LPC Connector ............................................................................................................... 26

PS2 ..................................................................................................................................26

Innoage HDD Power ......................................................................................................27

Expansion Slots .............................................................................................................28

Installing the M.2 Module .............................................................................................28

Battery ............................................................................................................................29

Chapter 3 - BIOS Setup ............................................................................................................... 30

Overview ...............................................................................................................................30

Main .......................................................................................................................................31

Advanced .............................................................................................................................31

ACPI Configuration ........................................................................................................ 32

CPU Configuration .........................................................................................................33

Video Configuration .......................................................................................................33

Audio Configuration.......................................................................................................34

SATA Configuration .......................................................................................................34

USB Configuration .........................................................................................................35

USB Power Control ........................................................................................................35

PCI Express Configuration ............................................................................................ 36

System Agent (SA) Configuration ................................................................................37

ME Configuration ........................................................................................................... 37

Active Management Technology Support ...................................................................38

MEBX Configuration ......................................................................................................38

Debug Configuration .....................................................................................................39

UEFI Device Manager ....................................................................................................39

SIO NCT6126D ............................................................................................................... 40

Console Redirection ......................................................................................................42

Security .................................................................................................................................43

Boot .......................................................................................................................................43

Exit ......................................................................................................................................... 45

Updating the BIOS ................................................................................................................ 45

Notice: BIOS SPI ROM..........................................................................................................45

Chapter 4 - RAID ..........................................................................................................................46

RAID Levels Explanation ...................................................................................................... 46

Setup Procedure ................................................................................................................... 46

4User's Manual | CMS630

About this Manual

This manual can be downloaded from the website.

The manual is subject to change and update without notice, and may be based on editions that

do not resemble your actual products. Please visit our website or contact our sales representa-

tives for the latest editions.

Warranty

1. Warranty does not cover damages or failures that occur from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper in-

stallation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in

or out of warranty. It must be returned to the purchase point, factory or authorized ser-

vice agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequential damages to

the product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you

are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, con-

tacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or

connectors by their ends.

Safety Measures

• To avoid damage to the system, use the correct AC input voltage range.

• To reduce the risk of electric shock, unplug the power cord before removing the sys-

tem chassis cover for installation or servicing. After installation or servicing, cover the

system chassis before plugging the power cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other

components. Perform the upgrade instruction procedures described at an ESD

workstation only. If such a station is not available, you can provide some ESD pro-

tection by wearing an antistatic wrist strap and attaching it to a metal part of the

system chassis. If a wrist strap is unavailable, establish and maintain contact with

the system chassis throughout any procedures requiring ESD protection.

5User's Manual | CMS630

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• 1 CMS630 motherboard

• 1 COM port cables (Length: 300mm, 2 x COM ports) A81-015026-023G

• 1 Serial ATA data cable (Length: 500mm) 332-553001-005G

• 1 I/O shield TBD

• 1 M.2 screw/standoff TBD

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance with the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Optional Items

• USB 2.0 port cable (Length: 350/398mm )

• USB3.2 Gen2 port cable (Length: 300mm )

• COM port cable (Length: 300mm, 2 x COM ports)

• Serial ATA data cable (Length: 500mm, W/LOCK)

• Thermal solution (For 35W, Height: 37.3mm)

• Thermal solution (For 65W, Height: 72.8mm)

• Thermal solution (For 95W, Height: 69.3mm)

• DP to HDMI Dongle

• PS2 KB/MS Cable (Length: 400mm)

• EXT-RS232 (4 ports RS-232 LPC module)

• EXT-RS485 (4 ports RS-485 LPC module)

• M.2-COM4 (M.2 serial port module)

• M.2-2LAN (M.2 LAN port module)

• M.2-2PSE (M.2 PSE module)

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance with the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

When installing the system board in a new system, you will need at least the following internal

components.

• Memory module

• Storage device such as a hard disk drive.

• Power supply

External system peripherals may also be required for navigation and display, including at least

a keyboard, a mouse and a video display monitor.

Chapter 1

INTRODUCTION

User's Manual | CMS630

Chapter 1 - Introduction

X Specifications

SYSTEM Processor 10th Generation Intel® LGA 1200 Socket Processors, TDP sup-

port up to 125W

Intel® Xeon® W-1290E (10 Cores, 20M Cache, up to 4.8 GHz,

ECC support); 95W (W480E only)

Intel® Xeon® W-1290TE (10 Cores, 20M Cache, up to 4.5 GHz,

ECC support); 35W (W480E only)

Intel® Xeon® W-1270E (8 Cores, 16M Cache, up to 4.8 GHz,

ECC support); 80W (W480E only)

Intel® Xeon® W-1270TE (8 Cores, 16M Cache, up to 4.4 GHz,

ECC support); 35W (W480E only)

Intel® Xeon® W-1250E (6 Cores, 12M Cache, up to 4.7 GHz,

ECC support); 80W (W480E only)

Intel® Xeon® W-1250TE (6 Cores, 12M Cache, up to 3.8 GHz,

ECC support); 35W (W480E only)

Intel® Core™ i9-10900E (10 Cores, 20M Cache, up to 4.7 GHz);

65W

Intel® Core™ i9-10900TE (10 Cores, 20M Cache, up to 4.5 GHz);

35W

Intel® Core™ i7-10700E (8 Cores, 16M Cache, up to 4.5 GHz);

65W

Intel® Core™ i7-10700TE (8 Cores, 16M Cache, up to 4.4 GHz);

35W

Intel® Core™ i5-10500E (6 Cores, 12M Cache, up to 4.2 GHz);

65W

Intel® Core™ i5-10500TE (6 Cores, 12M Cache, up to 3.7 GHz);

35W

Intel® Core™ i3-10100E (4 Cores, 6M Cache, 3.8 GHz, ECC sup-

port on W480E SKU); 65W

Intel® Core™ i3-10100TE (4 Cores, 6M Cache, to 3.6 GHz, ECC

support on W480E SKU); 35W

Intel® Pentium® G6400E (2 Cores, 4M Cache, 3.8 GHz); 58W

Intel® Pentium® G6400TE (2 Cores, 4M Cache, 3.2 GHz); 35W

Intel® Celeron® G5900E (2 Cores, 2M Cache, 3.2 GHz); 58W

Intel® Celeron® G5900TE (2 Cores, 2M Cache, 3.0 GHz); 35W

Chipset Intel® W480E/Q470E Chipset

Memory Four 288-pin Non-ECC UDIMM up to 128GB (Core™ i5/i7 only

support non-ECC)

Dual Channel DDR4 2400/2666/2933MHz (ECC support: W480E

only)

BIOS Insyde SPI 128Mbit

GRAPHICS Controller Intel® HD Gen 9 Graphics

Feature OpenGL 4.5, DirectX 12, OpenCL 2.1

HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG,

HEVC/H265, VP8, VP9

HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9

Display 1 x VGA, resolution up to 1920x1200 @ 60Hz

1 x DP++, resolution up to 4096x2160 @ 60Hz

1 x HDMI 1.4b, resolution up to 4096x2160 @ 24Hz

Triple Dis-

plays

VGA + DP++ + HDMI

EXPANSION Interface 1 x PCIe x16 (Gen 3) (1 x16 signal or 2 x8 signal)

3 x PCIe x4 (Gen 3) (2 x4 signal and 1 x1 signal)

2 x PCI

1 x M.2 2242/2260/2280 M key (PCIe Gen3 x4 NVMe/SATA/

Intel® Optane Memory and intel RST support)

1 x M.2 2242/2260/2280 M key (PCIe Gen3 x4 NVMe/Intel®

Optane Memory and intel RST support)

1 x M.2 2230 E key (USB 2.0/PCIe x1 shared with PCIe x1 slot,

opt., MOQ required)

AUDIO Audio Codec Realtek ALC888

ETHERNET Controller 1 x Intel® I211AT PCIe (10/100/1000Mbps)

1 x Intel® I219LM PHY with iAMT12.0 (10/100/1000Mbps)

(only Xeon, Core i9/ i7/i5 supports iAMT)

REAR I/O Ethernet 2 x GbE (RJ-45)

Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)

USB 2 x USB 3.2 Gen2

2 x USB 3.2 Gen1

4 x USB 2.0

Display 1 x VGA

1 x DP++

1 x HDMI

Audio 1 x Line-out, 1 x Mic-in, 1 x Line-in (opt., MOQ required)

INTERNAL I/O Serial 1 x RS-232/422/485 (RS-232 w/ power) (2.54mm pitch)

4 x RS-232 (2.54mm pitch)

USB 2 x USB 3.2 Gen 2 (Key B 20-pin)

2 x USB 2.0 (2.54mm pitch, Colay vertical Type A, opt.: MOQ

required)

1 x USB 2.0 Vertical Type A

Audio 1 x Front Audio Header

1 x S/PDIF

Chapter 1

INTRODUCTION

User's Manual | CMS630

SATA 4 x SATA 3.0 (up to 6Gb/s, SATA 3) RAID 0/1/5/10

DIO 1 x 16-bit DIO

LPC 1 x LPC (supports LPC EXT-RS232/RS485 module)

SMBus 1 x SMBus

PS/2 1 x PS/2 (mini-DIN-6)

WATCHDOG

TIMER

Output &

Interval

System Reset, Programmable via Software from 1 to 255

Seconds

SECURITY TPM Infineon TPM2.0 (opt., MOQ required)

POWER Type ATX

Connector 8-pin ATX 12V power

24-pin ATX power

Consumption TBD

RTC Battery CR2032 Coin Cell

OS SUPPORT Windows 10 IoT Enterprise 64-bit

Windows Server 2019

ENVIRONMENT Temperature Operating: -5 to 65°C

Storage: -30 to 60°C with RTC Battery; -40 to 85°C without RTC

Battery

Humidity Operating: 5 to 95% RH

Storage: 5 to 95% RH

MTBF TBD

MECHANICAL Dimensions ATX Form Factor

305mm (12") x 244mm (9.6")

Height PCB: 1.6mm

Top Side: TBD Bottom Side: TBD

CERTIFICA-

TIONS

Certifications CE, FCC Class B

Chapter 1

INTRODUCTION

User's Manual | CMS630

X Features

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so that

your system will continue to operate.

DDR4

DDR4 delivers increased system bandwidth and improves performance. The advantages of

DDR4 provide an extended battery life and improve the performance at a lower power than

DDR3/DDR2.

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of

up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s.

Gigabit LAN

Two Intel

Gigabit LAN controllers support up to 1Gbps data transmission.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It is

supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power Man-

agement Event) signal. However, if your system is in the Suspend mode, you can power-on the

system only through an IRQ or DMA interrupt.

Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a system from the

S3 (STR - Suspend To RAM) state.

PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to scale speeds

by forming multiple lanes. The x4 PCI Express lane supports transfer rate of 4 Gigabyte per

second (2 directions). The PCI Express architecture also supports high performance graphics

infrastructure by enhancing the capability of a PCIe x16 Gen 3 at 16GB/s bandwidth (8GB/s in

each direction).

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enables PCs to implement Power Manage-

ment and Plug-and-Play with operating systems that support OS Direct Power Management.

ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM

function.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing

the power button or selecting “Standby” when you shut down Windows

without having to go

through the sometimes tiresome process of closing files, applications and operating system.

This is because the system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The operating ses-

sion will resume exactly where you left off the next time you power-on the system.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

USB

The system board supports the new USB 3.2 Gen 2. It is capable of running at a maximum

transmission speed of up to 10 Gbit/s (1250 MB/s), and is faster than USB 2.0 (480 Mbit/s,

or 60 MB/s) and USB 1.1 (12Mb/s). USB 3.2 reduces the time required for data transmission,

reduces power consumption, and is backward compatible with USB 2.0. It is a marked improve-

ment in device transfer speeds between your computer and a wide range of simultaneously ac-

cessible external Plug and Play peripherals.

RTC Timer

The Real Time Clock (RTC) installed on the system board allows your system to automatically

power-on on the set date and time.

Chapter 1

INTRODUCTION

User's Manual | CMS630

X Block Diagram

W480E/

Q470E

Channel A

SATA 3.0

SMBus

DDI

HDA

LPC

S/PDIF

Front Audio

Audio Jack

(Line-out/Mic-in/Line-in (opt.))

RS232/422/485 2x

RS232 4x

DDR4 2400/2666/2933MHzDIMM

M.2 E key 1x (opt.)

SATA 4x

TCA6416

SMBus

VGA

Realtek

ALC888

Super IO

with WDT

Fan Control

H/W Monitor

Case Open

DMI 3.0

LGA 1200

GbE

LAN 1

USB 3.2 Gen2 2x

GLAN I211AT

MDI

USB 2.0

USB 2.0 2x

colay vertical Type A

LPC

LPC Header

SPI

SPI BIOS

Channel A

DDR4 2400/2666/2933MHzDIMM

Channel B

DDR4 2400/2666/2933MHzDIMM

Channel B

DDR4 2400/2666/2933MHzDIMM

PTN3355

DDI

DP++

HDMI

PCIe x4

PCIe x4 2x

PCIe x1

TPM 2.0 (opt.)

USB 2.0

USB 3.2 Gen2/Gen1

PCIe x1

LAN 2

USB 3.2 Gen1 2x

GLAN I219LM

MDI

USB 2.0

USB 3.2 Gen1

USB 3.2 Gen2/Gen1

USB 3.2 Gen2 2x

(Key B 20-pin)

USB 2.0

USB 2.0 4x

PS/2 KB/MS

PCIe x16

PCIe x16 2x (1 x16 or 2 x8 signal)

PCIe x1

IT8893E

PCI

PCI 2x

DDI

ASM1442K

USB 2.0 1x

Vertical Type A

USB 2.0

DIO 16-bit

PCIe x4 1x (default)

PCIe x4/SATA

M.2 M key 1x

PCIe x4

M.2 M key 1x

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

Chapter 2 - Hardware Installation

X Board Layout

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives,

add-in boards, and other components. Perform installation procedures at an ESD

workstation only. If such a station is not available, you can provide some ESD pro-

tection by wearing an antistatic wrist strap and attaching it to a metal part of the

system chassis. If a wrist strap is unavailable, establish and maintain contact with

the system chassis throughout any procedures requiring ESD protection.

Note:

Some components are optional and only available upon request.

M.2 E Key

2230

(Opt.)

M.2 M Key

DDR4_1

DDR4_2

DDR4_3

DDR4_4

Socket LGA1151

+12V Power

CPU FAN

Battery

JP11/12/13/14/15

PCIe 2 (PCIe x4)

PCI 1

PCI 2

JP1

JP2

JP4

JP3

S/PDIF

Front Audio

JP8

JP10

JP6

1 9

COM4

COM5

COM6

COM2

COM3

Buzzer

USB2_11/12

1 2

7 8

ATX Power

Front

Panel

LAN LED

SPI Flash

BIOS

PCIe 1 (PCIe x16)

Digital I/O

JP7

System

Fan 1

System Fan 3

SATA 1

(R3)

SATA 0

(R2)

SATA 3

(R5)

SATA 2

(R4)

Mic-in

Line-out

Line-in (opt.)

VGA

COM 1

HDMI

DP++

LAN 2

USB3_1/2

USB2_1/2

LAN 1

USB3_3/4

USB2_3/4

USB7~10

110

Intel

W480/Q470

LPC

PCIe 3 (PCIe x16)

PCIe 4 (PCIe x4)

PCIe 5 (PCIe x4)

JP23

J12

1 1

DIO Power

USB2_14

System Fan 2

1 9

JP5

(Clear CMOS)

USB2_5/6

USB3_5/6

1120

PS2

JP26

SDJ2

JP27

CN37

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X System Memory

• Four 288-pin Non-ECC UDIMM up to 128GB (Core™ i5/i7 only support

non-ECC)

• Dual Channel DDR4 2400/2666/2933MHz (ECC support: W480E only)

Features

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits from the memory channels. DIMMs are on the same

channel. DIMMs in a channel can be identical or completely different. However, we highly rec-

ommend using identical DIMMs. Not all slots need to be populated.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides

better system performance because it doubles the data transfer rate.

Before installing the memory module, please make sure that the following safety cautions are

well-attended.

1. Make sure the PC and all other peripheral devices connected to it has been powered

down.

2. Disconnect all power cords and cables.

3. Locate the DIMM socket on the system board

4. Make sure the notch on memory card is aligned to the key on the socket.

X System Memory

Installing the DIMM Module

Socket Side View

Socket Top View

Memory Module

Notch

Key

Eject TabEject Tab

DDR4_1

DDR4_2

DDR4_3

DDR4_4

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

Please follow the steps below to install the memory card into the socket.

Step 1:

Press the eject tabs at both ends of the socket outward and downward to release them from

the locked position.

Step 2:

Insert the memory card into the slot while making sure the notch and the key are aligned.

Press the card down firmly with fingers while applying and maintaining even pressure on both

ends.

Step 3:

The tabs snap automatically to the edges of the card and lock the card in place.

X System Memory

X Installing the DIMM Module

Please follow the steps below to remove the memory card from the socket.

Step 1:

Press the eject tabs at both ends of the socket outward and downward to release them from

the locked position.

Step 2:

The memory card ejects from the slot automatically.

Step 3:

Hold the card by its edges and remove it from the slot.

X System Memory

Removing the DIMM Module

Step 3

Step 2

Step 1

Step 2

Step 3

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

Installing the CPU Fan and Heat Sink

The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circula-

tion across the CPU and heat sink, the CPU will overheat damaging both the CPU and system

board.

Before you place the heat sink on the CPU, you must apply a thermal paste onto the top of the

heat sink. The thermal paste is usually supplied when you purchase the fan with heat sink as-

sembly. Do not spread the paste all over the surface. When you later place the CPU on top of

the heat sink, the compound will disperse evenly.

Some heat sinks come with a patch of pre-applied thermal paste. Do not apply thermal paste if

the fan with heat sink already has a patch of thermal paste on its underside. Peel the strip that

covers the paste before you place the CPU on top of the heat sink.

X CPU

There are 4 screw holes around the CPU for the heat sink to be mounted.

Align the 4 screw holes and tighten the heat sink up by inserting screws, DO remember to con-

nect the fan cable on the board. (The location of fan connector may vary.)

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

CLEAR CMOS Data

JP5

If any anomaly of the followings is encountered —

a) CMOS data is corrupted;

b) you forgot the supervisor or user password;

c) failure to start the system due to BIOS mis-configuration

— it is suggested that the system be reconfigured with default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, please follow the steps below.

1. Power-off the system and unplug the power cord.

2. Put a jumper cap on pin 2 and pin 3. Wait for a few seconds and set it back to its de-

fault setting, i.e. jumper cap on pin 1 and pin 2.

3. Plug the power cord and power-on the system.

 2-3 On: Clear CMOS Data  1-2 On: Normal (default)

13 2 13 2

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

COM1/COM2 RS232/422/485 Select

JP10

JP8

JP6

(COM 2)

JP1/JP2/JP3 (for COM 1) and JP6/JP8/JP10 (for COM 2) are used to configure the COM

ports to RS232, RS422 (Full Duplex) or RS485. When COM 1 RS232/422/485 is selected, JP1

and JP2 must be set in accordance to JP3. When COM 2 RS232/422/485 is selected, JP6 and

JP8 must be set in accordance to JP10. The pin functions of the COM ports will vary according

to the jumpers’ setting.

JP2

JP3

JP1

(COM 1)

 JP1/JP2 (COM1), JP6/JP8 (COM2)

1-3, 2-4 On:

RS232 (default)

3-5, 4-6 On:

RS422 Full Duplex

3-5, 4-6 On:

RS485

2 4 6

1 3 5

2 4

3 5

2 4 6

1 3 5

 JP3 (COM 1)/JP10 (COM 2)

1-3, 4-6 On:

RS232 (default)

3-5, 4-6 On:

RS422 Full Duplex

3-5, 2-4 On:

RS485

2 4 6

1 3 5

2 4 6

1 3 5

2 4 6

1 3 5

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

COM1/COM2 RS232 Power Select

JP4

(COM 1)

JP7

(COM 2)

JP4 (for COM 1) and JP7 (for COM 2) are used to configure Serial COM ports to pure RS232

or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to JP4’s and

JP7’s setting respectively.

 JP4 (COM 1) / JP7 (COM 2)

1-3, 2-4 On:

RS232 (default)

3-5, 4-6 On:

RS232 with power

2 4

3 5

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

DIO Power & Voltage - JP11/12/13/14/15

X Jumper Settings

AT/ATX Mode - JP26

JP11/12/13/14/15

2-3 On:

1-2 On:

5VSB (default)

JP15 is used to set DIO Power Voltage. JP11/12/13/14 is used to set DIO Power.

JP26 is used to switch between AT/ATX Mode.

2-3 On:

3V3SB

1-2 On:

GND (default)

 JP11 (DIO 0~3 PWR) / JP12 (DIO 4~7 PWR) / JP13 (DIO 8~11 PWR) / JP14 (DIO 12~15 PWR)

 JP15

1-2 On:

DIO PWR (default)

2-3 On:

GND

JP26

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

PWM Control - JP23

JP23

2-3 On:

1-2 On:

5VDU (default)

JP23 is used to set PWM control.

 JP23

X Jumper Settings

InnoAGE HDR1

JP27

JP27 is used to set InnoAGE functions.

 JP27

Pins Signals

1 INNOAGE_PCRST#

2 INNOAGE_RECOV#

3 INNOAGE_PWRLED#

4 INNOAGE_HDDLED#

5 INNOAGE_PWRBTN#

6 GND

1 2

5 6

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Jumper Settings

M.2 Connector Power Control - M2JP1 / M2JP2

M2JP2

2-3 On:

3V3DU

1-2 On:

3V3 (default)

M2JP1 and M2JP2 are used to control the power of M2CN1(M.2-M1) and M2CN2(M.2-M2).

M2JP1

Chapter 2

HARDWARE INSTALLATION

User's Manual | CMS630

X Rear I/O Ports

The rear panel I/O ports consist of the following:

• 1 DP++

• 2 USB 3.2 Gen2 ports

• RJ45 LAN 1/2

• 1 HDMI port

• 1 VGA port

• RJ45 LAN 1/2

• 2 USB 3.1 Gen 1 ports

• 1 Line-in jack (optional)

• 1 Line-out jack

• 1 Mic-in jack

• 1 COM 1

• 4 USB 2.0

VGA

COM 1

Line-out

Mic-in

DP++

HDMI

USB 2.0

LAN 2 LAN 1

USB 3.2

Gen1

USB 3.2

Gen2

Page is loading ...

DFI CMS630-W480E/Q470E Owner's manual

Brand: DFI

Model: CMS630-W480E/Q470E

Type: Owner's manual

This manual is also suitable for

CMS630

Download PDF

report

DFI CMS630-W480E/Q470E Owner's manual

This manual is also suitable for

DFI CMS630-W480E/Q470E Owner's manual

Related papers

Other documents