Kwikset 99140-019 User manual

Brand: Kwikset

Model: 99140-019

Type: User manual

1 / 4

66073001

Rev 01

ZWave® Plus

Installation and User Guide

ENGLISH

If drilling a new door, use the supplied template and the complete

door drilling instructions available at www.kwikset.com/doorprep.

Note: Additional door preparation may be

required for doors with 11/2" (38 mm) holes.

Consult the deadbolt drilling instructions at

www.kwikset.com/doorprep.

backset

Measure to conirm that the hole in

the door is either 21/8" (54 mm) or

11/2" (38 mm).

Measure to conirm that the backset is

either 23/8" or 23/4" (60 or 70 mm).

23/8" or 23/4"

60 or 70 mm 13/8" – 2"

35 – 51 mm

Measure to conirm that the hole in

the door edge is 1" (25 mm).

Measure to conirm that the door is

between 13/8" and 2" (35 mm and

51 mm) thick.

A B C D

21/8"

54 mm

11/2"

38 mm

25 mm

1Prepare the door and check dimensions

Required tools

Ruler4 AA Batteries

Hammer Wood block

Phillips head screwdriver

Additional Tools (depending on application)

N or P

(2x)

N P

A D

Is the door edge chiseled? Which latch are you installing?

YES NO

Use latch “A”. If the

latch bolt is not already

extended, extend the

latch bolt as shown.

wood

block

actual

size

Use latch “B” (not

included). If the latch

bolt is not already

extended, extend the

latch bolt as shown.

Latch “A” Latch “B”

S (2x) C

Q (2x)

Longer screws

install closest to

the door jamb.

door frame

EInstall strike on the door frame.

Make sure the hole in the door frame is drilled a

minimum of 1" (25 mm) deep.

chiseled not

chiseled

2Install the latch and strike

Kwikset

Technical Support

1-866-863-6584

www.kwikset.com

CIs the D-shaped hole centered in the door hole?

Hold the latch in front of the door hole, with the latch

face lush against the door edge.

YES NO

No adjustment is required.

Proceed to next step.

D-shaped hole D-shaped hole

Rotate latch face as

shown to extend latch.

Latch

“B” is not included. If needed,

please contact Kwikset to order

a drive-in latch for your lock.

Strike

Keys

Exterior Assembly

Adapter

Ring

Mounting

Plate

Parts in the box

Fasteners

03809 46780

48654 64109

49191

Contemporary

Interior Assembly

SmartKey

Tool

Traditional

F F

Contemporary

K L

actual

size

21/8"

54 mm

11/2"

38 mm

2 / 4

(2x)

What is the diameter of the hole in the door?

Remove battery cover and battery pack from interior assembly.

Install 4 AA batteries in battery pack.

Install interior assembly onto mounting plate.

Press and HOLD the Lock button

while installing battery pack.

Hold button until the latch bolt

starts moving on its own.

Did the latch bolt retract and extend on its own

when the battery pack was installed?

Locate screws for step 3C and keep them within reach.

Install exterior keypad and mounting plate.

B C

Diameter is 21/8"

(54 mm)

YES

Diameter is 11/2"

(38 mm)

“D” is required for installation.

Install “D” on “F”.

“D” is not needed for

installation. Discard “D”. Cable goes

underneath latch.

Support exterior

assembly during

mounting plate

installation.

Route cable through

center hole, then push

cable into bottom hole.

Insert key and

test latch. If latch

does not extend or

retract smoothly,

adjust screws (T).

Remove key when

inished and make

sure the latch bolt

is fully extended.

Keep parallel to

edge of door.

Tighten

screws evenly.

Make sure turnpiece is in

the vertical position.

Door handing process

was successful! Proceed

to next step after latch

bolt stops moving.

Remove battery pack,

wait 15 seconds, then

attempt the process again.

Note: Latch

bolt will only

retract half way.

Make sure

turnpiece shaft is

rotated as shown.

Ensure correct polarity.

For best results, use

new, non-rechargeable

Alkaline batteries only.

Do not install

batteries

until step 5.

Ensure tight cable

connection.

Lay excess cable lat inside the

bottom of the interior housing.

align

actual

size

bottom

hole

TT (2x)

3Install the exterior keypad

4Install the interior assembly

5Install the batteries and perform the door handing process

This step will teach your lock the orientation of your door and is crucial to lock operation.

green

red

Mastercode

For enhanced security,

a mastercode may

be used when adding

and deleting user

codes. For more

information about the

mastercode, download

the Programming and

Troubleshooting Guide

on the SmartCode 914

page at kwikset.com.

Tip: You can press the

Lock button before

entering your user

code to light up the

keypad at night.

Add the lock to your smart home system

Initiate the process to add

the lock to your system at

your smart home controller.

Refer to your smart home

system instructions for

more information.

When prompted by your smart home system to add the

lock, press button “A” on the lock interior one time. The

red LED will illuminate when the lock enters Add Mode.

If successful, re-name the lock in your system

(if applicable).

If unsuccessful, follow your system's instructions to

remove the lock from the controller and any other

network, then press button “A” on the lock one time.

Perform steps 6A6C again.

If still unsuccessful, consult the Programming and

Troubleshooting Guide on the SmartCode 914 page

at www.kwikset.com.

A B C

button “A”

Please allow time for the controller to add the lock.

3 / 4

Conirm that the code(s) added in previous step can unlock the door.

One green lash with one beep Three red lashes with three beeps

Make sure the door is open. Press

the Program button once.

Locking the Door Unlocking the Door

Enter user code. A total of 30 user

codes may be programmed.

Press Lock button once.

A B C

What lights and sounds does the lock produce?

Each user code

must be a unique

code between

4 and 8 digits,

depending on

your smart

home system.

Programming was successful. Programming was unsuccessful.

Make sure not to pause for more than 5 seconds during programming.

Make sure the user code is not a duplicate and that it is between 4 and 8 digits

during your next attempt. Make sure the lock has room for an additional code.

If all user code positions are illed, delete a code to make room for this one.

Press Lock button once. Enter user code.

It is recommended that you add and

delete all user codes through your smart

home control system. If your system

does not allow this, codes may be added

directly to the lock as shown here.

Programming Timeout

During programming, if no button is

pressed for ive seconds, the system will

time out (indicated by three beeps and a

red lashing keypad), and you will need to

restart the procedure.

*Beeping sound will only be heard if switch #3 (on the lock interior) is in the on positon. See “Switches and Status LED Colors” on page 4.

Re-key the lock (if needed). Install the battery cover.

A B

IMPORTANT:

Remove battery

pack before

re-keying.

actual

size

V (3x)

a a

b b

Re-key the lock

to work with your

existing key. See

the supplied

SmartKey Re-key

instructions for

more information.

Reinstall

battery

pack.

Add user codes (30 max)

Re-key the lock (if needed) and install the battery cover

Test the lock (review normal operation)

Alert Reason Solution

Keypad lashes red once with

one beep*. One incorrect code entered. Re-enter code.

Keypad lashes red three

times with three beeps*.

No user code programmed. Program at least one user code.

Programming timeout after ive

seconds. Attempt programming procedure again.

Unsuccessful programming.

Keypad lashes red 15 times

with 15 beeps*

Three incorrect codes entered

within one minute.

Re-enter code after 60 second keypad

lockout.

Keypad lashes red with fast

beeping sound for three to

four seconds.

Low battery. Replace batteries.

Keypad lashes green with

continuous beeping sound

for two seconds.

Door jammed while attempting

to lock.

Manually re-lock door. If needed,

reposition strike.

Lock beeps continuously. Interior assembly is

disconnected from exterior.

Remove battery pack, reconnect the interior

to the exterior, then reinstall battery pack.

*Beeping sound will only be heard if switch #3 is on.

1. Read all instructions in their entirety.

2. Familiarize yourself with all warning and caution statements.

3. Remind all family members of safety precautions.

4. Protect your user codes and mastercode.

5. Dispose of used batteries according to local laws and regulations.

CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel

can change the user codes, you must restrict access to the back panel and routinely

check the user codes to ensure they have not been altered without your knowledge.

The use of a mastercode can help protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete security

by itself. This lock may be defeated by forcible or technical means, or evaded by

entry elsewhere on the property. No lock can substitute for caution, awareness of

your environment, and common sense. Builder’s hardware is available in multiple

performance grades to suit the application. In order to enhance security and reduce

risk, you should consult a qualiied locksmith or other security professional.

Important Safeguards

If no button is pressed for ive seconds, the system will time out, and

you will need to restart the procedure.

1 Keep door open.

Press Program

button once.

5 Re-enter user code. 6 Press Lock

button once. If unsuccessful

Make sure to enter

the same valid code

in steps 3 and 5.

Test code

While the door is

open, test the user

code to make sure

it no longer unlocks

the door.

2 Press Lock

button once.

4 Press Lock

button once.

3 Enter user code

to be deleted.

Network Information

ZWave System Notes

This product is a security enabled Z-wave Plus product and must be used with a Security

Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and

results may vary based on building construction and communication path.

To assure interoperability, each ZWave product must pass a stringent conformance test to

assure that it meets the ZWave standard for complete compliance with all other devices and

controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers

that their products will reliably perform with any other ZWave device. And, regardless of the

vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.

ZWave Coniguration and Association Parameters are available

on the SmartCode 914 page at www.kwikset.com.

Removing the lock from the network

Follow your smart home system’s instructions

to remove the lock from the network. When

prompted by the system, press button A” on the

lock interior once.

4 / 4

SmartCode at a Glance

Deleting a single user code

Note: All codes may be deleted at once if the mastercode is enabled. For more information about the

mastercode, consult the Programming and Troubleshooting Guide.

Reference Guide

Exterior

Back

panel

Program

button

Status

LED

Switches

Turnpiece

shaft

Note: When the cover is removed,

the turnpiece shaft can be used to

manually lock and unlock the door.

Interior (cover removed)

Switches and Status LED colors Troubleshooting

Switch Function

1Door lock status LED blinks every 6

seconds

Lock automatically re-locks door 30

seconds after unlocking. Disabled if no

codes are programmed.

3 Audio

4 Not used.

Color Lock Status

Blinking green Unlocked

Blinking amber Locked

Blinking red Low battery

Solid red

Door handing process

did not work properly.

See the online

Programing and

Troubleshooting Guide.

1 2 3 4

Switches

Status

LED

O

System Alerts

Factory Reset

A factory reset will delete all codes associated with the lock,

and it will remove it from your smart home system.

Status

LED

1 Remove

battery pack.

2 Press and HOLD the Program

button while reinserting

the battery pack.

Keep holding the button for 30

seconds until the lock beeps

and the status LED lashes red.

Keypad

Lock

button

Keyway

SmartKey

tool hole

Button “A” Button “B”

3 Press the Program button

once more. When the LED

lashes green and you

hear one beep, the lock

has been reset.

4 Perform the door handing process again

to teach the lock the orientation of the

door, pair the lock with your smart home

system, and add user codes to your lock.

A complete Programming and Troubleshooting Guide is

available on the SmartCode 914 page at www.kwikset.com.

Kwikset 99140-019 User manual

Kwikset 99140-019 User manual

Kwikset 99140-019 User manual

Related papers

Other documents