Pulsar AWZ518 Operating instructions

Brand: Pulsar

Model: AWZ518

Type: Operating instructions

PC2

AWZ 518

v.1.0

Time module for AC control

04062009 EN

Edition: 1st from the 23rd May of 2008

Supercedes edition: ----------

1. Technical description.

1.1. General description.

PC2 (AWZ 518) time module is used for control of AC supply state of object alarm systems (monitoring

transmitters, alarm centrals, DC power supply unit etc.). The module makes it possible to pass information about decay

of AC supply with the set delay time of T (3s/63s/17m37s/4h45m, +/-2%) and information about recovery of AC supply.

Recovery of AC voltage (transient) during counting of T delay time triggers counting reset (i.e. stop and return to the

normal state). The module has an AC1 input that shall be connected to a secondary wiring terminal of a transformer

supplying the device (the module shall be supplied by 12V/DC, i.e. the device to which the controlled transformer

terminal is connected). PC2 has two OC outputs (OC1, OC2) and a LED (L1) indicating the state of the device. Two Z1

and Z2 jumpers are used for configuration of the signalling delay time of AC supply decay.

1.2. The connection diagram of the module (fig.1).

Fig.1. The connection diagram of the PC2 module (example).

1.3. Description of the elements and connectors of the PC2 module and their functions (tab.1, tab.2, fig.2).

Table 1.

No.

[fig.2

Description of the element

[1]

Green LED L1 – signalling of the module state

• lights continuously: AC voltage at AC1 terminal, state H,

active supply of the VDC module

• flickers 1x/1s: AC voltage at the terminal, state L (no supply),

counting of the delay time

• does not light: the module counted time and changed the state of OC

outputs (optionally no 12V DC supply)

[2]

Z1, Z2 jumpers- configuration of the signalling delay time of AC decay

• Z1= , Z2= delay time T= 3s

• Z1= , Z2= delay time T= 1 min 5s

• Z1= , Z2= delay time T= 17 min 40s

• Z1= , Z2= delay time T= 4h 45 min

inserted jumper

removed jumper

[3] Connectors of the PC2 module

Table 2.

[3] Description of the module connectors

AC1 Input of AC controlled voltage (a secondary wiring terminal of a transformer)

+VDC

- VDC

DC supply input

(+VDC= +12V, -VDC= 0V, GND)

OC1*

OC output for signalling of AC state:

• normal state: L (0V, GND),

• active state: hi-Z (high impedance)

OC2*

OC output for signalling of AC state:

• normal state: hi-Z (high impedance)

• active state: L (0V, GND) of OC type

Normal state: AC voltage is active at AC1 terminal or counting of delay time after

decay of AC voltage

Active state: no AC voltage at AC1 terminal, finished counting of delay time

Fig.2. The view of the PC2 module.

1.3. Technical parameters:

- electrical parameters (tab.3)

- mechanical parameters (tab.4)

Table 3.

Supply voltage 10V÷15V/DC (-5%/+5%)

Current consumption 5mA max.

Ranges of T delay settings 3s/65s/17m40s/4h45m (-2%/+2%)

AC1 input

0V-30V AC (-2%/+2%)

state L ( ‘0’ logical)= 0V-1,5V AC

state H (‘1’ logical)= 5V-30C AC

GND= terminal of ‘VDC-‘ supply

(voltage of secondary wiring of separation and power-

supply transformer)

Technical outputs:

- OC1 output

- OC2 output

OC type 50mA max.

• normal state: L (0V, GND),

• active state: hi-Z (high impedance)

• normal state: hi-Z (high impedance)

• active state: L (0V, GND)

Optical signalling Green LED L1

Operation conditions environment class II, -10°C ÷40°C

Table 4.

PCB dimensions 42 x 35 x 23 (WxLxH)

Fixation Mounting pins x 4 (PCB fi=4,2 mm)

or assembly belt

Connectors Ф0,41÷1,63 (AWG 26-14)

Net/gross weight 30/50 g

2. Installation.

2.1 Requirements.

The time module shall be mounted by the qualified installer having appropriate (required and necessary for a

given country) permissions and qualifications for connecting (operating) low-voltage installations. The unit shall be

mounted in closed rooms, according to the environment class II, of the normal air humidity (RH=90% max. without

condensation) and the temperature within the range from -10°C to +40°C. The module shall be connected only to power

sources having galvanic (transformer) separation from the network supply.

The unit shall be mounted in a metal casing (a cubicle, a terminal device) and in order to fulfill LVD and EMC

requirements the rules for power-supply, encasing and shielding shall be observed according to application.

2.2 Installation procedure.

1. Install a casing (a cubicle etc.) and lead cables through cable penetrations.

2. Install the PC2 time module on mounting pins or assembly belt (the pins shall be installed before a casing or a cubicle

is mounted).

3. Supply DC voltage to +VDC, -VDC terminals retaining polarization.

4. Supply AC controlled voltage to AC1 terminal.

5. Connect the signal of AC decay, i.e. OC1 or OC2 (depending on purpose of application) to a signalling device (LED,

transmitter input, central input, indicator etc.).

6. Fix the signalling delay time of OC1 and OC2 outputs by means of Z1 and Z2 jumpers.

7. After the tests and operation control are performed, a casing (a cubicle etc.) shall be closed.

WEEE MARK

The waste electrical and electronic equipment, do not mix with general household

waste. There are separate collection systems for waste electrical and electronic

equipment in accordance with legislation under the WEEE Directive and is effective

only with EU.

WARRANTY

24 months since the sale date, 36 months since the production date.

THE WARRANTY IS VALID ONLY after presenting the invoice of the sale to which the claim refers.

Pulsar K.Bogusz Sp.j.

Siedlec 150,

32-744 Łapczyca, Poland

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50

e-mail: biuro@pulsar.pl, sales@pulsar.pl

http:// www.pulsar.pl

Pulsar AWZ518 Operating instructions

Pulsar AWZ518 Operating instructions

Pulsar AWZ518 Operating instructions

Related papers

Other documents