Patton electronic 4900 User manual

Brand: Patton electronic

Model: 4900

Category: Networking

Type: User manual

This manual is also suitable for

SmartNode 4900

IpChannel Bank

User Manual

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: suppor[email protected]

WWW: www.patton.com

Part Number: 07MSN4900-GS, Rev. H

Revised: February 8, 2012

Start Installation

For Quick

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

Tel: +1 (301) 975-1000

Fax: +1 (301) 869-9293

Support: +1 (301) 975-1007

Web: www.patton.com

E-mail: support@patton.com

Trademark Statement

The terms SmartNode, SmartWare, and SmartView are trademarks of Patton

Electronics Company. All other trademarks presented in this document are the prop-

erty of their respective owners.

The information in this document is subject to change without notice. Patton Elec-

tronics assumes no liability for errors that may appear in this document.

Important Information

To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities

with the SmartNode 4900, you may need to purchase additional licenses, hardware,

software, network connection, and/or service. Contact sales@patton.com or

+1 (301) 975-1000 for assistance.

Warranty Information

The software described in this document is furnished under a license and may be used

or copied only in accordance with the terms of such license. For information about the

license, see Appendix E, "End user license agreement" on page 70 or go to

www.patton.com.

Patton Electronics warrants all SmartNode router components to be free from defects,

and will—at our option—repair or replace the product should it fail within one year

from the first date of the shipment.

This warranty is limited to defects in workmanship or materials, and does not cover

customer damage, abuse or unauthorized modification. If the product fails to perform

as warranted, your sole recourse shall be repair or replacement as described above.

Under no condition shall Patton Electronics be liable for any damages incurred by the

use of this product. These damages include, but are not limited to, the following: lost

profits, lost savings and incidental or consequential damages arising from the use of or

inability to use this product. Patton Electronics specifically disclaims all other warran-

ties, expressed or implied, and the installation or use of this product shall be deemed

an acceptance of these terms by the user.

Summary Table of Contents

1 General information...................................................................................................................................... 15

2 Applications overview.................................................................................................................................... 21

3 Hardware installation.................................................................................................................................... 24

4 Getting started with the SmartNode 4900 Series........................................................................................... 36

5 LEDs status and monitoring ......................................................................................................................... 46

6 Contacting Patton for assistance ................................................................................................................... 48

A Compliance information .............................................................................................................................. 51

B Specifications ................................................................................................................................................ 55

C Port pin-outs ................................................................................................................................................ 61

D Factory Configuration .................................................................................................................................. 68

E End user license agreement ........................................................................................................................... 70

F Installation checklist .................................................................................................................................... 73

G Accessories .................................................................................................................................................... 75

Table of Contents

Summary Table of Contents ........................................................................................................................... 3

Table of Contents ........................................................................................................................................... 4

List of Figures ................................................................................................................................................. 8

List of Tables .................................................................................................................................................. 9

About this guide ........................................................................................................................................... 10

Audience............................................................................................................................................................... 10

Structure............................................................................................................................................................... 10

Precautions ........................................................................................................................................................... 11

Safety when working with electricity

Preventing Electrostatic Discharge Damage ....................................................................................................13

General observations .......................................................................................................................................13

Typographical conventions used in this document................................................................................................ 14

General conventions .......................................................................................................................................14

1 General information...................................................................................................................................... 15

SmartNode 4900 Series overview...........................................................................................................................16

SmartNode 4900 Series detailed description..........................................................................................................17

SmartNode 4900 Series front panel ................................................................................................................18

SmartNode 4900 Series rear panels .................................................................................................................19

Reset button behavior ...............................................................................................................................20

2 Applications overview.................................................................................................................................... 21

Introduction..........................................................................................................................................................22

SmartNode 4900 Series applications......................................................................................................................22

Multiservice carrier access over leased lines ......................................................................................................22

Enterprise FXS concentration and extension over IP and T1/E1 .....................................................................23

Bulk analog line extensions .............................................................................................................................23

3 Hardware installation.................................................................................................................................... 24

Introduction..........................................................................................................................................................25

Planning the installation........................................................................................................................................25

Installation checklist .......................................................................................................................................26

Site log ............................................................................................................................................................26

Network information ......................................................................................................................................27

Network diagram ......................................................................................................................................27

IP related information ...............................................................................................................................27

Configuration tools .........................................................................................................................................27

AC Power Mains .............................................................................................................................................27

Location and mounting requirements .............................................................................................................28

Installing the IpChannel Bank

...............................................................................................................................28

Unpacking the Model SN4900 series IpChannel Bank ...................................................................................28

IpChannel Bank chassis installation ................................................................................................................28

SmartNode 4900 User Manual Table of Contents

Connecting cables ...........................................................................................................................................29

Connecting the FXS ports .........................................................................................................................29

Connecting the FXO ports ........................................................................................................................29

Connecting the Ethernet ports ..................................................................................................................30

Connecting the 10/100Base-T Ethernet ports to an Ethernet switch or hub .......................................30

Connecting a 10/100Base-T Ethernet port to an Ethernet-capable workstation ..................................31

Connecting the EIA-561 RS-232 configuration port (DCE configured) ...................................................31

Connecting the serial port .........................................................................................................................31

Connecting power ...........................................................................................................................................32

Grounding the Model SN4900—AC and DC units .................................................................................32

Installing the power cables—AC units .......................................................................................................33

Installing the power cables—DC units ......................................................................................................34

4 Getting started with the SmartNode 4900 Series........................................................................................... 36

Introduction..........................................................................................................................................................37

1. Configure IP address .........................................................................................................................................38

Factory-default IP settings ...............................................................................................................................38

Connect to the RS-232 console port ...............................................................................................................39

Login ..............................................................................................................................................................40

Changing the WAN IP address .......................................................................................................................40

2. Connecting the SmartNode to the network .......................................................................................................41

3. Loading the configuration (optional).................................................................................................................41

Bootloader.............................................................................................................................................................42

Start Bootloader ..............................................................................................................................................42

Start-up with factory configuration .................................................................................................................43

Load a new application image (SmartWare) via TFTP ....................................................................................43

Load a new application image (SmartWare) via the serial link .........................................................................45

Additional information..........................................................................................................................................45

5 LEDs status and monitoring ......................................................................................................................... 46

Status LEDs...........................................................................................................................................................47

6 Contacting Patton for assistance ................................................................................................................... 48

Introduction..........................................................................................................................................................49

Contact information..............................................................................................................................................49

Warranty Service and Returned Merchandise Authorizations (RMAs)...................................................................49

Warranty coverage ..........................................................................................................................................49

Out-of-warranty service .............................................................................................................................50

Returns for credit ......................................................................................................................................50

Return for credit policy .............................................................................................................................50

RMA numbers ................................................................................................................................................50

Shipping instructions ................................................................................................................................50

A Compliance information

.............................................................................................................................. 51

Compliance ...........................................................................................................................................................52

EMC compliance: ...........................................................................................................................................52

SmartNode 4900 User Manual Table of Contents

Safety compliance: ..........................................................................................................................................52

PSTN Regulatory Compliance: .......................................................................................................................52

Radio and TV interference (FCC Part 15).............................................................................................................52

CE Declaration of Conformity ..............................................................................................................................52

Authorized European Representative .....................................................................................................................52

FCC Part 68 (ACTA) Statement (FXO ports).......................................................................................................54

Industry Canada Notice (FXO Ports) ....................................................................................................................54

B Specifications ................................................................................................................................................ 55

Voice connectivity - FXS .......................................................................................................................................56

Voice connectivity - FXO......................................................................................................................................56

Ethernet interface ..................................................................................................................................................56

Console port..........................................................................................................................................................56

Serial ports.............................................................................................................................................................56

FXS ports ..............................................................................................................................................................57

FXO ports .............................................................................................................................................................57

PPP and Frame-Relay support...............................................................................................................................57

Voice processing (signaling dependent) .................................................................................................................57

Fax and modem support........................................................................................................................................57

Voice signaling ......................................................................................................................................................58

Voice routing-session router ..................................................................................................................................58

IP services..............................................................................................................................................................58

Management .........................................................................................................................................................59

Operating environment .........................................................................................................................................59

Temperature ...................................................................................................................................................59

Humidity ........................................................................................................................................................59

Altitude ...........................................................................................................................................................59

System...................................................................................................................................................................59

Dimensions ...........................................................................................................................................................59

Weight and power dissipation ...............................................................................................................................59

Power supply .........................................................................................................................................................60

Universal AC version ......................................................................................................................................60

DC version .....................................................................................................................................................60

Identification of the SmartNode devices via SNMP...............................................................................................60

C Port pin-outs ................................................................................................................................................ 61

Introduction..........................................................................................................................................................62

Console port

..........................................................................................................................................................62

Ethernet 10Base-T and 100Base-T port ................................................................................................................62

Sync Serial port .....................................................................................................................................................63

FXS and FXO ports...............................................................................................................................................64

D Factory Configuration .................................................................................................................................. 68

Introduction..........................................................................................................................................................69

E End user license agreement ........................................................................................................................... 70

SmartNode 4900 User Manual Table of Contents

End User License Agreement.................................................................................................................................71

1. Definitions ..................................................................................................................................................71

2. Title ............................................................................................................................................................71

3. Term ...........................................................................................................................................................71

4. Grant of License ..........................................................................................................................................71

5. Warranty ....................................................................................................................................................71

6. Termination ................................................................................................................................................72

7. Other licenses .............................................................................................................................................72

F Installation checklist .................................................................................................................................... 73

Introduction..........................................................................................................................................................74

G Accessories .................................................................................................................................................... 75

Introduction..........................................................................................................................................................76

List of Figures

1 Model SN4932 IpChannel Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2 Model SN4932 IpChannel Bank front panel LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 SmartNode 4900 rear panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4 Multiservice carrier access over leased lines application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5 Enterprise FXS concentration and extension over IP and T1/E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

6 Bulk analog line extensions application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

7 Model SN4900 Ethernet port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

8 Straight-through RJ-45-to-RJ-45 Ethernet cable diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

9 Cross-over RJ-45-to-RJ-45 Ethernet cable diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

10 DB-9-to-RJ-45 cable diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

11 IEC-320 connector and grounding stud locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

12 Grounding stud and power cable retainer clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

13 DC connector, -DC and +DC input view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

14 Connecting the SmartNode to your laptop PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

15 Connecting the SmartNode to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

16 Loading the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

17 Connecting to the RS-232 Console port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

18 Connecting the SmartNode to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

19 EIA-561 (RJ-45 8-pin) port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

20 Model SN4900 Ethernet port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

List of Tables

1 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2 Front panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3 Port descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4 Rear panel expansion port LED descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5 Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

6 Sample site log entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

7 IP addresses/subnets for SN4900 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

8 Serial port pin-outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

9 Factory default IP address and network mask configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

10 SmartNode LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

11 Rear panel expansion port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

12 SmartNode weight and maximum power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

13 SmartNode Models and their Unique sysObjectID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

14 V.35 serial port signals (DB-25 connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

15 X.21 serial port signals (DB-15 connector) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

16 Band marked color-codes for the 64-pin RJ-21X connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

17 Band marked color-codes for the 50-pin RJ-21X connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

18 Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

19 Accessory cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

About this guide

This guide describes the SmartNode 4900 Series IpChannel Bank hardware, installation and basic configura-

tion. For detailed software configuration information refer to the SmartWare Software Configuration Guide and

the available Configuration Notes.

Audience

This guide is intended for the following users:

• Operators

• Installers

• Maintenance technicians

Structure

This guide contains the following chapters and appendices:

• Chapter 1, “General information” on page 15 provides information about router features and capabilities

• Chapter 2, “Applications overview” on page 21 contains an overview describing router operation

and applications

• Chapter 3, “Hardware installation” on page 24 provides quick start hardware installation procedures

• Chapter 4, “Getting started with the SmartNode 4900 Series” on page 36 describes getting started with the

SmartNode IpChannel Bank

• Chapter 5, “LEDs status and monitoring” on page 46 contains definitions for the LED status indicators

• Chapter 6, “Contacting Patton for assistance” on page 48 contains information on contacting Patton tech-

nical support for assistance

• Appendix A, “Compliance information” on page 51 contains compliance information for the SmartNode

• Appendix B, “Specifications” on page 55 contains for the specifications for the IpChannel Bank

• Appendix C, “Port pin-outs” on page 61 provides cable pinouts for the various interface ports

• Appendix D, “Factory Configuration” on page 68 lists the factory configuration settings for the SmartNode

4900 Series devices

• Appendix E, “End user license agreement” on page 70 provides detailed information on the EULA

• Appendix F, “Installation checklist” on page 73 lists the tasks for installing the SmartNode 4900 IP

Channel Bank

For best results, read the contents of this guide before you install the IpChannel Bank.

SmartNode 4900 User Manual About this guide

Precautions

Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you

become aware of potential problems. Warnings are intended to prevent safety hazards that could result in per-

sonal injury. Cautions are intended to prevent situations that could result in property damage or

impaired functioning.

Note

A note presents additional information or interesting sidelights.

The alert symbol and IMPORTANT heading calls attention to

important information.

The alert symbol and CAUTION heading indicate a potential

hazard. Strictly follow the instructions to avoid

property damage.

The shock hazard symbol and CAUTION heading indicate a

potential electric shock hazard. Strictly follow the instructions to

avoid property damage caused by electric shock.

The alert symbol and WARNING heading indicate a potential safety hazard.

Strictly follow the warning instructions to avoid personal injury.

The shock hazard symbol and WARNING heading indicate a potential electric

shock hazard. Strictly follow the warning instructions to avoid injury caused

by electric shock.

IMPORTANT

CAUTION

WARNING

SmartNode 4900 User Manual About this guide

Safety when working with electricity

The SmartNode contains no user serviceable parts. The equipment shall be

returned to Patton Electronics for repairs, or repaired by qualified service per-

sonnel. Opening the SmartNode case will void the warranty.

Mains Voltage: Do not open the case when either power cord is attached. The

SmartNode router is equipped with dual power supplies. Disconnect both

power supply cords before servicing. For systems without a power switch,

line voltages are present within the power supply when the power cords are

connected. The mains outlet that is utilized to power the SmartNode router

shall be within 10 feet (3 meters) of the device, shall be easily accessible, and

protected by a circuit breaker.

The Model SN4900 is not shipped with power cables. For AC powered units,

ensure that the power cable used meets all applicable standards for the coun-

try in which it is to be installed, and that it is connected to a wall outlet which

has earth ground.

Hazardous network voltages are present in WAN ports regardless of whether

power to the SmartNode is ON or OFF. To avoid electric shock, use caution

when near WAN ports. When detaching the cables, detach the end away from

the SmartNode first.

Because telephone line voltages can be dangerous, when detaching the net-

work cables, disconnect the end away from the SmartNode first.

Do not work on the system or connect or disconnect cables during periods of

lightning activity.

The Model SN4900 can only be configured with two AC power

supplies or two DC supplies, you cannot mix AC and DC sup-

plies in the same chassis.

In accordance with the requirements of council directive 2002/

96/EC on Waste of Electrical and Electronic Equipment (WEEE),

ensure that at end-of-life you separate this product from other

waste and scrap and deliver to the WEEE collection system in

your country for recycling.

WARNING

CAUTION

SmartNode 4900 User Manual About this guide

Preventing Electrostatic Discharge Damage

When starting to install interface cards place the interface card on its shielded plastic bag if you lay it on

your bench.

Electrostatic Discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic

printed circuit cards are improperly handled and can result in complete or intermittent failures.

General observations

• C

lean the case with a soft slightly moist anti-static cloth

• Place the unit on a flat surface and ensure free air circulation

• Avoid exposing the unit to direct sunlight and other heat sources

•

Protect the unit from moisture, vapors, and corrosive liquid

Always follow ESD prevention procedures when removing and

replacing cards.

Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the

chassis frame to safely channel unwanted ESD voltages

to ground.

To properly guard against ESD damage and shocks, the wrist

strap and cord must operate effectively. If no wrist strap is avail-

able, ground yourself by touching the metal part of the chassis.

CAUTION

SmartNode 4900 User Manual About this guide

Typographical conventions used in this document

This section describes the typographical conventions and terms used in this guide.

General conventions

The procedures described in this manual use the following text conventions:

Table 1. General conventions

Convention Meaning

Garamond blue type

Indicates a cross-reference hyperlink that points to a figure, graphic, table, or sec-

tion heading. Clicking on the hyperlink jumps you to the reference. When you

have finished reviewing the reference, click on the Go to Previous View

button in the Adobe® Acrobat® Reader toolbar to return to your starting point.

Futura bold type Commands and keywords are in boldface font.

Futura bold-italic type Parts of commands, which are related to elements already named by the user, are

in boldface italic font.

Italicized Futura type Variables for which you supply values are in italic font

Futura type

Indicates the names of fields or windows.

Garamond bold type Indicates the names of command buttons that execute an action.

< >

Angle brackets indicate function and keyboard keys, such as <SHIFT>, <CTRL>,

<C>, and so on.

[ ] Elements in square brackets are optional.

{a | b | c} Alternative but required keywords are grouped in braces ({ }) and are separated

by vertical bars ( | )

blue screen Information you enter is in blue screen font.

screen Terminal sessions and information the system displays are in screen font.

node The leading IP address or nodename of a SmartNode is substituted with node in

boldface italic font.

SN The leading SN on a command line represents the nodename of the SmartNode

# An hash sign at the beginning of a line indicates a comment line.

Chapter 1 General information

Chapter contents

SmartNode 4900 Series overview...........................................................................................................................16

SmartNode 4900 Series detailed description..........................................................................................................17

SmartNode 4900 Series front panel ................................................................................................................18

SmartNode 4900 Series rear panels .................................................................................................................19

Reset button behavior ...............................................................................................................................20

SmartNode 4900 Series overview 16

SmartNode 4900 User Manual 1 • General information

SmartNode 4900 Series overview

The IpChannel Bank 4900 Series are Analog Access Routers that support 12 to 32 VoIP calls. Filling the gap

between small media gateways and T1/E1 gateway equipment, the SN4900 Series IpChannel Bank fits your

needs cost effectively—so you won’t have to “stack” multiple smaller units or buy an over-designed product.

Figure 1. Model SN4932 IpChannel Bank

The following base models are available:

• IpChannel Bank 4912 (12 VoIP calls)

• IpChannel Bank 4916 (16 VoIP calls)

• IpChannel Bank 4924 (24 VoIP calls)

• IpChannel Bank 4932 (32 VoIP calls)

Refer to appendix B, “Specifications” on page 55 for a complete feature description of the SN4900 Series.

The SmartNode 4900 Series comes equipped with two 10/100Base-T Ethernet ports, from 12 to 32 FXS

ports, and an integrated optional V.35 or X.21 serial-WAN port. This provides voice-over-IP (VoIP) and

Internet telephony integrated with routed serial-WAN access. The SN4900 IpChannel Bank supports Frame-

Relay and PPP networking with VPN and firewall functions and provides extensive quality of service (QoS)

features for best-possible voice quality over any broadband IP network.

The SmartNode IpChannel Bank performs the following major functions:

• Voice over IP and local switching via a combination of 12, 16, 24, or 32 analog phone ports (FXS).

• Voice over IP and local switching via a combination of 12, 16, 24, or 32 analog ports (FXO) for

SN4900/JO models.

• Standards-compliant conversion between analog voice and digital VoIP in accordance with SIP and

H.323 protocols.

• Internet access and IP Routing with IP QoS support for mixed voice and data traffic.

• Routed LAN-to-WAN connectivity between two 10/100 Ethernet LAN ports and a synchronous serial

V.35 or X.21 WAN interface.

SmartNode 4900 Series detailed description 17

SmartNode 4900 User Manual 1 • General information

SmartNode 4900 Series detailed description

The SmartNode 4900 Series IpChannel Bank provides VoIP calling from 12 to 32 analog phone lines. Inte-

grated within the IpChannel Bank are 2 Ethernet ports, one for LAN, the other for WAN connectivity. The

WAN service connection may also be made via either a serial V.35 or X.21 port. The front panel contains LED

indicators for system status-at-a-glance, and the rear panel provides connectivity for the FXS or FXO analog

ports, the ENET ports, a WAN port, and an RS-232 control port.

Each model in the SN4900 series comes equipped with two 10/100Base-T Ethernet ports. The IpChannel

Bank optionally may come with a V.35 or X.21 serial WAN port. Ethernet port ETH0/1 is commonly used for

the LAN connection. ETH0/0 can be used for WAN access or as a second LAN connection. The customer’s

application will determine whether the serial expansion port or ETH0/0 is used for WAN connectivity. The

following base model numbers are available:

• SN4912/JSx/RUI (12 FXS ports)

• SN4916/JSx/RUI (16 FXS ports)

• SN4924/JSx/RUI (24 FXS ports)

• SN4932/JSx/RUI (32 FXS ports)

• SN4912/JO/RUI (12 FXO ports)

• SN4916/JO/RUI (16 FXO ports)

• SN4924/JO/RUI (24 FXO ports)

• SN4932/JO/RUI (32 FXO ports)

Note

The model-code suffixes indicate the following features according to

the following conventions:

•

JS indicates FXS ports are present

•

JO indicates FXO ports are present

•

RUI indicates dual redundant, integrated universal input (UI)

power supply

•

where x may be:

- C to indicate a V.35 port is present

- D to indicate an X.21 port is present

- If the model number does not include a JSC or JSD, it means there is no

serial port

SmartNode 4900 Series detailed description 18

SmartNode 4900 User Manual 1 • General information

SmartNode 4900 Series

front panel

The front panel LEDs display the status of the power, system, VOIP channels, Ethernet ports, and call load.

The front panel includes the following LEDs. Figure 2 shows the front panel LED indicators and table 2 pro-

vides a description of the LED indicators’ behavior.

Figure 2. Model SN4932 IpChannel Bank front panel LEDs.

Table 2. Front panel LEDs

LED LED Condition Description

Power Solid Green Power is applied

Run Solid green

Blinking green

System is idle.

System is busy.

VoIP Solid green VoIP ports are active

ETH0 Solid green

Blinking green

Ethernet Port 0 is up

Indicates activity

ETH1 Solid green

Blinking green

Ethernet Port 1 is up

Indicates activity

20% Green 20% of the voice ports are active

40% Green 40% of the voice ports are active

60% Green 60% of the voice ports are active

80% Green 80% of the voice ports are active

100% Green 100% of the voice ports are active

UNIT EQUIPPED WITH DUAL SUPPLIES

ISCONNECT BOTH SUPPLIES

BEFORE SERVICIN

ToIP Integrated Access Device

l B

VOIP LINK

ETH 0/0

ETH 0/1

RUN

ETH 0/1

POWER

100%80%60%40%20%

CALL LOAD

ToIP Integrated Access Device

IpChannel Bank

VOIP LINK

ETH 0/0

ETH 0/1

RUN

POWER

20% CALL LOAD LED

40% CALL LOAD LED

60% CALL LOAD LED

100% CALL LOAD LED

80% CALL LOAD LED

ETH 0/1 LED

ETH 0/0 LED

VOIP LINK LED

RUN LED

POWER LED

100%80%60%40%20%

CALL LOAD

SmartNode 4900 Series detailed description 19

SmartNode 4900 User Manual 1 • General information

SmartNode 4900 Series rear panels

The SmartNode 4900 rear panel ports are shown in figure 3 and described in table 3 on page 20.

Figure 3. SmartNode 4900 rear panels

Model SN4932

4932/JSC/UI

49xx/JSC/UI

49xx/JSD/UI

100-240V

(50-60 Hz)

1 AMP

UNI

T EQUIPPED WITH DUAL S

PPLIES

DISCONNECT BOTH SUPPLIES

BEFORE SER

VICING

UNIT EQUIPPED WITH DU

AL SUPPLIES

DISCONNECT BOTH SUPPLIES

BEFORE SERVICING

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console

Telco Ports

Reset

ExpansionETH 0/1

Status

Activity

4932/JSD/UI

4932/JS/UI

49xx/JSC/48

4932/JSC/48

Expansion port

Ethernet ports

Console port

Telco ports

36-72V

1.6 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

ConsoleResetExpansionETH 0/1

Status Activity

36-72V

1.6 AMP

Telco Ports

36-72V

1.6 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetExpansionETH 0/1

Status Activity

36-72V

1.6 AMP

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetETH 0/1

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetETH 0/1

Status Activity

Expansion

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetExpansionETH 0/1

Status Activity

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetExpansionETH 0/1

Status Activity

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

Console Telco PortsResetExpansionETH 0/1

Status Activity

100-240V

(50-60 Hz)

1 AMP

100-240V

(50-60 Hz)

1 AMP

ETH 0/0

NIC ADDRESS

00:A0:BA:00:04:10

ConsoleResetExpansionETH 0/1

Status Activity

SmartNode 4900 Series detailed description 20

SmartNode 4900 User Manual 1 • General information

Reset button behavior

For those SmartNode devices that have a Reset button on the rear panel, its behavior is as follows:

• To restart the unit with the current startup configuration—Press for less than 1 second and release the Reset

button. The SmartNode will restart with the current startup configuration.

• To restart the unit with factory default configuration—Press the Reset button for 5 seconds until the Power

LED starts blinking. The unit will restart with factory default configuration.

• To restart the unit in bootloader mode (to be used only by trained SmartNode technicians)—Start with the

unit powered off. Press and hold the Reset button while applying power to the unit. Release the Reset button

when the Power LED starts blinking so the unit will enter bootloader mode.

Table 3. Port descriptions

Port Description

ETH 0/0 (WAN Ethernet 0/0 port) 10/100Base-Tx full-/half-duplex, RJ-45, auto detection and auto-

MDI-X connects the unit to an Ethernet WAN device (for example,

a cable modem, DSL modem, or fiber modem).

ETH 0/1 (LAN Ethernet 0/1 port) 10/100Base-Tx full-/half-duplex, RJ-45, auto detection and fall-

back, connects the unit to an Ethernet LAN.

Expansion

•

V.35 serial port—DB-25 connector, data rates up to 2 Mbps,

Frame Relay or PPP protocols, Status and Activity

LED indicators, configured as DTE

•

X.21 serial port—DB-15 connector, data rates up to 2 Mbps,

Frame Relay or PPP protocols, Status and Activity

LED indicators, configured as DTE

Console (RS-232 control port) Used for service and maintenance, the Console port, an RS-232

RJ-45 connector with EIA-561 pinout, connects the router to a

serial terminal such as a PC or ASCII terminal (also called a dumb

terminal). Asynchronous default data rate 9600 bps, hardware

DSR and DTR signals for external modems are wired directly

together internally

FXS Ports (4900/JS models) For connection of up to 32 analog FXS devices (selectable for 12,

16, 24, or 32). Either a 50-pin or 64-pin RJ21X connector that

connects the router to an analog terminal (a telephone, for exam-

ple) FXO port. EuroPOTS support (ETSI EG201 188).

FXO Ports (4900/JO models) For connection of up to 32 analog FXO devices (selectable for

12, 16, 24, or 32). FXO RJ-11(6 position, 4 wire) connectors that

connect the product with an analog line (FXS port). EuroPOTS sup-

port (ETSI EG201 188).

Table 4. Rear panel expansion port LED descriptions

LED Indication Description

Status Solid yellow Proper signals are present for modem communication

Activity Flashing yellow Transmit or receive traffic is present on the serial interface

Page is loading ...

Patton electronic 4900 User manual

Brand: Patton electronic

Model: 4900

Category: Networking

Type: User manual

This manual is also suitable for

Download PDF

report

Patton electronic 4900 User manual

This manual is also suitable for

Patton electronic 4900 User manual

Related papers

Other documents