Ax32V Camera Series
Instruction Manual
Before attempting to connect or operate this product, please read these instructions carefully and save this
manual for future use.
CONTENTS
INTRODUCTION .................
....................................................
SPECIFICATIONS ...............................................................
INSTALLATION..................................................................
2
3
5
Annexxus Mini Network Dome Camera User Guide Ax32V Models
All rights reserved. No part of this manual may be reproduced or transmitted in any form or by
any means, electronic or mechanical, including photocopying, recording, or by any information
storage or retrieval system, without the prior written permission of the copyright owner and the
publisher. Annexxus is a registered trademark of i³ International. i³ reserves the right to change
the contents of this manual without notice.
Disclaimer
Annexxus Mini Network Dome Camera User Guide is provided as is, without warranty of any
kind, expressed or implied, including but not limited to performance, merchantability, or fitness for
any particular purpose. Neither i³ International Inc. nor its dealers or distributors shall be liable to
any person or entity with respect to any liability, loss, or damage, caused or alleged to have been
caused directly or indirectly by this information. Furthermore i³ International Inc. reserves the
right to revise this publication, and to make changes to the content at any time, without notice.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Address:
i³ International Inc. • 780 Birchmount Road, Unit 16 • Scarborough • Ontario • Canada M1K 5H4
Tech Support: 1.877.877.7241 or email to: supp[email protected]
Web Site: www.i3international.com
1
1 Introduction
Thank you for purchasing an i³ Annexxus Network Camera. The Ax32V models are vandal-proof
dome cameras that can be viewed on site or remotely. They come with i³’s Annexxus Web Viewer
software which operates on an Internet Explorer web browser platform so is easy to install and
offers a range of user-friendly video functions.
The Ax32V cameras integrate perfectly into i³ International’s SRX-Pro DVMS systems.
1.1 Precautions
Safety
1. This quick start guide is designed for users who have an adequate knowledge of network
cameras.
2. Do not touch the imaging surface of the sensor. Use a soft cloth moistened with alcohol to
clean the surface if it is touched accidentally.
3. Ensure the power supply voltage is correct for the particular variant of camera before
operation.
4. Do not attempt to service this camera yourself unless you are authorized to do so. Opening the
camera may expose you to electrocution or other hazards. Refer all servicing to qualified
personnel only.
5. For more details on installation and operation, please refer to the CD provided.
1.2 Unpacking
Camera Parts and Definition
Hardware/Software Requirements
2
Ax32V2M series Specifications:
Model Ax32V2M series
Parameter 2 megapixel CMOS IP Vandal-Proof Indoor Dome Camera
Camera
Image Sensor 1/3 inch CMOS
Electronic Shutter 1/25s ~1/100,000s
Min. Illumination
Color: 0.5Lux @ F1.2
B / W: 0.1Lux @ F1.2
Lens
4mm, F1.2 Fixed Iris (2.8, 6, 8mm optional)
Angle of view: 90°
Day / Night Electronic
Video Parameter Saturation/Brightness/Contrast/ adjustable through client software or web browser
Adjustment Range Pan±15°, Tilt0~90°, Rotation±15°
Compression Standard
Video Compression H.264/Mpeg4/MJpeg
Bit rate 32 Kbps~16Mbps
Audio Compression OggVorbis
Image
Max. Image
Resolution
1600 x 1200
Frame Rate 15fps (1600 x 1200), 30fps (1280 x 720)
Function
e-PTZ Yes
Storage Support NAS, ISCSI
Intelligent Alarm Motion Detection, Video Tampering, Video Loss, Network Broken, IP address
conflict, Storage exception
Protocols TCP/IP,HTTP,DHCP,DNS,DDNS,RTP/RTCP,PPPoE,FTP,SMTP,NTP,SNMP,HTTP
S, SIP, 802.1x, IPV6
Basic Initial Set button, Anti-flicker, Dual Stream, Heartbeat, Password Protection,
watermark
3-Axis adjustment Yes
Interface
Audio Internal Microphone optional
Communication
Interface
1 RJ45 10M / 100M self adaptive Ethernet port
General
Operating Condition -10°~60°, Humidity 90% or less(non-condensing)
Power Supply DC12V±10% / PoE
Power
Consumption
3W MAX
Impact Protection IEC60068-275Eh,50J;EN50102, exceeding IK10
Weather Proof IP66
Dimensions(mm) 100×97.5×46.5
Weight 250g
3
Ax32VD1 Series Specifications
Model Ax32VD1 Series
Parameter VGA Real-time CMOS Mini IP Vandal-proof Dome Camera
Camera
Image Sensor 1/4 inch CMOS
Electronic Shutter 1/25s ~1/100,000s
Min. Illumination
Color: 0.1 Lux @ F1.2
B / W: 0.01Lux @ F1.2
Lens
4mm, F1.2 Fixed Iris(2.8, 6, 8mm optional)
Angle of view: 71°
Day / Night Electronic
Video Parameter Saturation/Brightness/Contrast/ adjustable through client software or web browser
Adjustment Range Pan±15°, Tilt0~90°, Rotation±15°
Compression Standard
Video Compression H.264/Mpeg4/MJpeg
Bit rate 32 Kbps~8Mbps
Audio Compression OggVorbis
Image
Max. Image Resolution 640×480
Frame Rate 30fps @ 640×480
Function
Storage Support NAS, ISCSI
Intelligent Alarm
Motion Detection, Video Tampering, Video Loss, Network Broken, IP address conflict,
Storage exception
Protocols
TCP/IP,HTTP,DHCP,DNS,DDNS,RTP/RTCP,PPPoE,FTP,SMTP,NTP,SNMP,HTTPS,
SIP, 802.1x, IPV6
Basic
Initial Set button, Anti-flicker, Dual Stream, Heartbeat, Password Protection,
watermark
3-Axis adjustment Yes
Interface
Audio Internal Microphone optional
Communication Interface 1 RJ45 10M / 100M self adaptive Ethernet port
General
Operating Condition -10°~60°, Humidity 90% or less(non-condensing)
Power Supply DC12V±10% / PoE
Power Consumption 3W MAX
Impact Protection IEC60068-275Eh,50J;EN50102, exceeding IK10
Weather Proof IP66
Dimensions(mm) 100×97.5×46.5
Weight 250g
4
2 Camera connection & Annexxus Installation
Topics covered
Connecting the network camera
Network camera IP configurations
Annexxus Web Viewer Installation and Setup details
Annexxus Advanced Setup
Note: Internet Explorer version 6.0 or higher is necessary to connect with an i3 International
network camera.
2.1 Connecting a network camera
Two methods of connecting a network camera and PC are shown below:
i³ iP-Pro Server
Crossover direct connection
LAN
VIA a Gigabit Switch
i³ iP-Pro Server
Connection type: 1
Connection type: 2
Network camera
Network camera
Network camera
Network camera
2.2 Network Camera Default IP Configurations
The RJ-45 Network Port on the network camera will connect to an Ethernet/Fast Ethernet
standard (10/100Base-TX) network, complying with the IEEE 802.3U standard. Annexxus device
may be connected to a hub, switch or router with a straight through CAT5e cable, or directly to
the DVR/NVR with a crossover CAT5e cable.
Network Settings:
Ax32V Default IP configurations :
IP Address: 192.0.0.16
Subnet Mask: 255.255.255.0
2.3 Annexxus Web Viewer Installation and Setup details
Note: Internet Explorer version 6.0 or higher is necessary to connect with an i3 International
network camera.
2.3.1 Installing Annexxus Web Viewer and accessing Setup mode
1. Connect the network camera to the supported power source in accordance with the
connections diagram.
5
2. Connect the camera to a LAN/WAN network.
3. Before viewing, you may need to adjust your browser’s security settings. To do so:
From the Tool menu, click Internet Options.
Click on the Security tab.
If the camera is using the intranet, click the Local intranet icon. If the camera is using
the internet, click the Internet icon.
Click on Custom level. Under ActiveX controls and plug-ins, enable the following three
functions: ‘Download signed ActiveX controls’ ‘Run ActiveX control and plug-ins’
‘Script ActiveX controls marked safe for scripting”.
Click OK.
4. Open Internet Explorer browser window on a local PC/laptop and enter Annexxus IP address
(192.0.0.16 for Ax32V) in the address line.
5. When connecting for the first time, you may be prompted to install Annexxus 300 Active X
control. Click on the banner and select install the following Active X control ‘Annexxus 300’
from ‘I3 International Inc.’... from the context menu.
6
6. In the Internet Explorer - Security Warning window, click Install.
7. The Annexxus Web Viewer screen will be displayed with the Login window. Enter Annexxus
Username and Password and click Login.
Note
The login is case sensitive. The default administrative login is: Username: admin; Password:
1234
8. Annexxus Web Viewer opens and a live view from the camera appears.
9. To adjust parameters click the Setup button on the main screen
. See the Annexxus
Advanced Setup section (s.2.4) of this manual for more information.
2.3.2 Changing IP Address
Your Ax32V2M series Network camera comes with the pre-assigned IP scheme: IP Address
192.0.0.16; Subnet mask: 255.255.255.0
To change camera IP Address:
1. Install Annexxus Active X as in section (2.3). Open and login to Annexxus.
2. Click the Setup button on the main screen
and open the Network setup tab.
3. In the Network setup tab, configure IP settings, such as IP Address and Subnet Mask for LAN
connections or IP Address, Subnet Mask, and Gateway IP for WAN connections.
It is entirely the responsibility of a technician to be able to configure this setup page according to
customer’s network configurations.
7
4. Click the Save button and wait for the "Settings changes have been successfully saved”
message window to pop up. Click OK to close the message window.
5. Wait for “Please reboot Annexxus device to apply changes” window to pop up. Click OK. Click
Reboot button.
6. Wait for “Would you like to reboot Annexxus device?” window to pop up. Click OK.
7. Wait for “Annexxus device is rebooting. Close Internet Explorer browser, wait 45 seconds and
connect to Annexxus Viewer again” window to pop up. Click OK.
2.4 Annexxus Advanced Setup
To change additional network camera settings, click the Advanced Setup button
.
Four setup tabs are available in Advanced Setup: Device Information, Channels, Network and
User Management.
In the bottom of each setup window there are four control buttons: Restore, Reboot, Save and
Close.
The Restore button is available to authorized users only. Click it to restore the Annexxus device
settings to the factory default settings. Settings must be restored to factory default after each
firmware upgrade. WARNING: All custom settings will be lost, including any additional users.
The Reboot button is available to authorized users only. Click it to reboot the Annexxus device. A
device reboot is required after the video recording settings have been changed or after a firmware
upgrade. Read related section for instructions on rebooting the device.
8
The Save button is available to authorized users only. Click it to save any setting changes. To
prevent unauthorized users from making changes to the Annexxus device, disable the Save
button in the User Management setup tab.
The Close button closes the Advanced Setup window.
2.4.1 Device Information Setup
The following information about the Annexxus device can be found in the Device Information
setup: the number of video channels, sensor inputs, control outputs and internal storage devices
connected to the network, the current device firmware version and the device’s serial number.
Authorized users can also assign/change the device name, change the overwrite mode and
upgrade the device's firmware version.
NOTE: Overwrite Mode only functions when used in conjunction with SRX-Pro software.
Device Name
In Device Name, enter the camera’s custom name.
Firmware Upgrade
This function is only available to authorized users. Read the Upgrading Firmware section for
instructions on how to upgrade Annexxus device firmware.
9
V3.0 build 10/206
2.4.2 Channels Setup
In the Channels Setup, authorized users can perform the following tasks for each selected video
channel:
• Assign/change channel name.
• Display/hide channel name, change the position of the channel name on the video screen.
• Display/hide timestamp and day of the week; change the position of the timestamp on the video
screen; change the display style of the timestamp if enabled.
• Display/hide up to 4 personalized text messages on the video screen – called text overlay.
• Enable video privacy masking, set up to 4 video privacy masking areas.
• Change the display and recording resolution for the main and sub video streams.
• Change the display frame rate for the main and sub video streams.
• Change other transmission settings: I Interval, BitRate Type, BitRate, and Frame Type.
2.4.3 Network Setup
The RJ-45 Network Port on the IP camera allows it to be connected to an Ethernet/Fast Ethernet
standard (10/100Base-TX) network, complying with the IEEE 802.3U standard. Annexxus device
may be connected to a hub, switch or router with a straight through CAT5e cable, or directly to
the DVR/NVR with a crossover CAT5e cable.
See Annexxus Default IP Configurations section for information on Annexxus factory default IP
configurations.
In the Network Setup, authorized users can obtain the network camera's MAC Address; change
its IP Address, Subnet Mask, Gateway IP, Multicast IP, Host Port (for Video/Audio) and/or HTTP
Port (for Web access). Please contact your network administrator for more information on your
network particulars.
Important: Make sure to open all ports required for remote viewing. The following ports must be
forwarded: 80, 554, 8000, 8200.
10
Unique IP address must be assigned to each Annexxus unit before installation. Unless this step
is completed prior to installation, the customer will be unable to detect Annexxus module on their
LAN/WAN network. See Changing IP Address section for instructions on how to change
Annexxus IP address.
It is highly recommended to click Synchronize Clock to synchronize the camera to the time zone
in which it is used. If this isn’t done the time stamp on snapshots will not match the time of the
time zone.
2.4.4 User Management Setup
One administrator account and up to 15 additional accounts can be configured for the network
camera.
Administrator user
The default administrator user name is admin; the default password is 1234. The Administrator is
the only user that can change the administrator password. The administrator user name and user
privileges cannot be changed. If the administrator password is lost after being changed, use
Annexxus Finder to reset it to the factory default.
The administrator is the only user that can add, modify or delete additional operator users.
11
Operator user
Operator users will only have access to setup tabs and features that are specified in their user
privileges. Operator users cannot add, modify or delete other operator accounts.
An operator user can only change his/her own password.
2.4.4.1 Changing Administrator Password
To change the administrator password, you must be logged in as Administrator.
1. In the User Management setup tab, right-click on the Administrator account in the left-hand
pane and select Modify from the context menu.
2. Type in the new password in Password and Re-enter Password fields. The password may
only consist of numbers and may not exceed 16 characters.
3. Click Save to save the new administrative password.
2.4.4.2 Adding/Modifying/Deleting Operator User
Adding/Modifying Operator User
To add a new operator user or to modify an existing operator user:
1. In the User Management setup tab, right-click on the desired Operator account in the left-hand
pane and select Modify from the context menu.
12
2. Enter the user name in User Name field. User name may not exceed 16 characters.
3. Enter the password in Password and Re-enter Password fields. The password may only
consist of numbers and may not exceed 16 characters.
4. Configure user privileges. The following privileges can be assigned to the operator user(s):
User Privilege
Privilege Limitation
Live Video Viewing
(configured per channel)
Check off to allow the operator to view live video.
Save Settings
Check off to allow the operator to make changes to
Annexxus setup.
Control PTZ (only applies to
Ax32V2M series model)
Check off to allow operator to control the camera’s
electronic Point/Tilt/Zoom (ePTZ) function.
Upgrade, Format,
Reboot
Check off to allow the operator to upgrade the camera
firmware or to reboot the Annexxus device.
To assign Live Video Viewing, check off Check Mark to Enable Privilege for Channel(s) then
make sure Channel 01 is checked. For the Save Settings, Control PTZ and Upgrade, Format,
Reboot privileges check off Check Mark to Enable Privilege.
13
5. Click Save to save changes to all user accounts
Deleting Operator User
To delete an operator user, do the following:
1. In the User Management setup tab, right-click on the desired Operator account in the left-hand
pane and select Delete from the context menu.
Note that the user will be deleted immediately and no warning message will be displayed.
3 Using Annexxus Web Viewer Interface
Topics covered:
Introduction to Annexxus Web Viewer
Live video streaming
Taking a live snapshot
3.1 Introduction to Annexxus Web Viewer
Annexxus Web Viewer contains the following buttons and areas:
1. Live Mode
2. Setup Mode
3. Login/Logout
4. Single Camera Screen Division
5. Full Screen
6. Snapshot
7. Live Backup
8. ChannelsTree List
9. ePTZ Control Panel – only applies to Ax32V2M series; disabled for Ax32VD1 Series
10. Video Adjustments Panel – only applies to Ax32V2M series; disabled for Ax32VD1 Series
11. CPU Usage Indicator
14
12. Current User
13. Current Date and Time
1
2 3 4
5 6 7
8
9
11
12 13
10
Note: The Audio Settings panel at the bottom left of the live view screen is disabled, because
neither the Ax32V2M series nor the Ax32VD1 series capture sound.
Note: The PTZ Control panel on the left side of the live view screen is disabled for the Ax32VD1
series, because this model does not support the PTZ or ePTZ function.
Note: The Video Adjustments panel on the left side of the live view screen is disabled for the
Ax32VD1 series, because this model does not support the video adjustments function.
The Annexxus Web Viewer contains the following buttons and areas:
Live Mode – displays the Annexxus Live mode. In Live mode, the user can control the
ePTZ function, adjust brightness/contrast/hue/saturation settings and save live snapshot or video
backup onto the local media storage.
Setup Mode– displays Annexxus setup options.
Full Screen - This button enlarges the live screen to fit your computer screen with no user
interface (no menu bars shown). To exit press F11 on your keyboard.
15
Live Backup - This button starts recording a backup video from the live network
camera. The video is saved on local media storage. Each backup file will be saved as a separate
file. Annexxus Player is needed to play back the *.axv live backup video clips. For more
information, see Live Backup section (s.3.4).
Live Snapshot – Clicking this button takes a snapshot of the live video screen. The
snapshot will be saved onto local media storage. For more information see Live
Snapshot section (s.3.5).
CPU Usage Indicator - displays the percentage of hard disk space used for
video display.
Current User - displays the current user logged into the Server.
Date and Time – displays the current date and time. This information
is acquired from Windows OS. If date/time is not correct, access the desktop and double-click the
Windows time display in the right-hand corner. Set the appropriate time and click Apply.
Video Adjustments panel (Ax32V2M series only) - adjusts Brightness, Contrast,
Hue and Saturation of the live video channel. Click the Undo button to reset all parameters to the
default settings.
3.2 Live Video Streaming
The network camera supports two simultaneous video streams: higher quality and higher
compression. Main stream is usually set to higher resolution and higher quality, while sub stream
is set to lower resolution and/or to lower quality. The user can switch between main and sub
video streaming to either see a better quality video image or to be able to view a faster video
stream over the Internet.
To select either the Main or Sub video stream for live viewing, right-click on the video screen and
select either Main stream or Sub stream from the context menu.
16
3.3 Electronic Pan/Tilt/Zoom (ePTZ) - Ax32V2M series only
Through the Annexxus Web Viewer, authorized users can control the Electronic Pan/Tilt/Zoom
(ePTZ) function of the network camera remotely. The ePTZ function does not apply to the
Ax32VD1 series model.
Make sure to properly connect the camera according to the Annexxus connections diagram.
The network camera ePTZ can be controlled through the Annexxus Web Viewer or through the
SRX-Pro/iP-Pro software (see SRX-Pro/iP-Pro software manual for more information).
It is important to note that certain image resolution levels affect the functioning of ePTZ. On
certain resolution levels ePTZ does not function at all. Figure 3.3 below indicates how resolution
affects ePTZ:
Figure 3.3
352x240 / 352x288
640x480 ePTZ fully functional
704x480 / 704x576
800x60
0
1280x720 No In/Out Zoom function
1280x960
1600x9
12 ePTZ does not function
1600x1200
17
3.3.1 Controlling ePTZ
Note: ePTZ does not work in Full Screen mode. Press F11 to exit Full Screen.
Using the ePTZ control panel located on the left of the live video dashboard the user can:
1. Change the pan-tilt settings.
2. Zoom in and out.
3. Enable one of nine presets, or enable the Auto Pattern feature.
To control Zoom/Iris direction or activate presets, follow the diagram below:
To control the Pan/Tilt position of the camera:
1. Select a camera resolution level that enables ePTZ. See figure 3.3 above.
2. To use Pan/Tilt, the iris cannot be fully zoomed out. After zooming in partially or all the way,
use the arrows on the ePTZ control wheel to pan and tilt.
Using the Presets
There are 9 preset iris positions to choose from. When using the Annexxus Web Viewer, these
presets are factory defaults and cannot be changed. Each preset, from 1-9, shifts the iris to a
different preset position, changing the live image view. Note that users can set the presets
themselves when using SRX-Pro/IP-Pro.
Auto Pattern
With Auto Pattern, the iris will continuously scan the view field from left to right. To use Auto
Pattern the iris cannot be fully zoomed out. After zooming in partially or all the way, select Auto
Pattern in the drop down menu.
3.4 Live Backup
Live Backup is the video recording feature of the network camera. It records onto the local PC
storage (local HDD, network HDD, or USB storage device). Recorded video is saved in the *.axv
format and can be played back with Annexxus Player 2.0. Note: The Annexxus Player 2.0
application is included on the CD which accompanies the network camera – see Appendix B for
instructions on using Annexxus Player 2.0.
To start Live Backup video recording:
18
1. Click the Live Backup button on the main screen . The Live Backup window will be
displayed.
2. In the Live Backup window, ensure the Channel 1 box is checked off.
3. Select Storage Location. Click Browse..., locate and select the destination folder on a local or
network hard drive, where the *.axv live video backup files will be stored. The default location is
C:\IP_Module_Recording.
4. Click OK to start the live video backup. The Live Backup button on the main screen will turn
blue to indicate that a live backup is in progress.
Each time a live backup is initiated, a new
*.axv file is created in the storage location folder.
The video backup files are named according to the following standard:
IPADDRESS_CHANNEL_YYYYMMDD_HHMMSS.axv.
For example, the video file 192.0.0.16_01_20100909_152712.axv was recorded from a
Ax32V2M series network camera located on the 192.0.0.16 IP address (the default IP address for
the camera), Video Channel 1, September 9, 2010 at 3:27PM.
To stop Live Backup video recording for one or more channels:
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
