1
Montage- und Gebrauchsanweisung
für den Dunstabzug
Instruction on mounting and use of the cooker hood
JDA 5330
2
A
B
B
C
C
C
D
D
Abb. 1
Fig. 1
Abb. 2 - Fig. 2
Abb. 3 - Fig. 3
F
3
E
F
G
H
S
S
Abb. 4 - Fig. 4
Abb. 5 - Fig. 5 Abb. 6 - Fig. 6
7
View of the hood - Fig. 1
1) Motor speed switch
2) Light switch
3) Extractable drawer
4) Metal grease filter
5) Cooking surface lighting
Use
The hood may be used in 2 ways:
External exhausting system
The air is expelled outside by means of
a pipe to be connected to the coupling
flange A (fig. 2).
Connecting the exhausting pipe
The coupling ring A has a diameter of 120mm.
We suggest to use Ø 120 mm exhausting
pipe.
Recycling version (filtering)
The air is purified by means of a carbon filter
and then returned to the room.
The active carbon filter can be ordered from
the supplier.
To install the filter, proceed as follow:
fit the filter into its seat B and fix with the two
hooks C (fig. 3).
The filtered air is discharged above the top
cabinet.
The baffle plate D (fig. 2) can be fitted to the
outlet hole using the screws supplied.
Installation
When installed, the hood must be not less
than 43 cm. above electric burners or 65
cm. above gas or mixed-fuel burners.
Warning!
— The hood cannot be connected to flues of
other appliances that run on energy
sources other than electricity.
— When the hood is used at the same time of
other appliances that run on energy sources
other than electricity, provision must be made
for an adequate supply of air.
— No food must be cooked flambé
underneath the hood.
The use of an unprotected flame is
dangerous for the filters and could cause
fires.
Therefore, never use an open flame under
the hood. When frying foods, never leave
the pan alone because the cooking oil
could flare up.
— Please, keep to the provisions of official
directives regarding the question of fume
discharge.
— The manufacturers refuse to accept any
responsibility for damage to the hood or
its catching on fire because of failure to
observe the above instructions.
Suggestions for the installation and
use of the hood
— The horizontal sections of the pipe must
be slanted slightly downwards (about
10%) to ensure the condensed vapour
not to come back on the motor of the
hood.
— The best performance of the unit is
obtained in the exhaust mode, therefore
in the limits of the possibilities it is advised
to use the external exhaust (suction) type.
— The best performances are obtained with
short pipes (max. 4 m) and with few
curves.
Electric connection
Before completing any connection, make
sure the house voltage corresponds with the
voltage indicated on the label affixed inside
the hood.
The hood is supplied with a standard plug;
connect it to a correspondingly standard
socket.
In the case is intended to connect the
appliance permanently to the mains after
having removed the plug supplied, must be
fitted a two-pole switch conforming to
regulations with an opening distance
between contacts of not less than 3mm.
The manufacturers are not liable for any
problems caused by the user’s failure to
observe the above instructions.
8
ventilator (left switch) and one for illuminating
the work surface (right switch).
Maintenance
Before performing any maintenance
operation, disconnect the hood from the
electricity.
Metal grease filter
Wash the filter, in a dishwasher or with
detergent and water, periodically according
to how often the appliance is used, but at
least once every30 days.
Before refitting the filter ensure that it is
perfectly dry.
Removing the Grease Filters
- Fig. 3
a. Remove the pull-out drawer completely.
b. Press the side handles (F) towards the
opposite side and remove the filters.
Putting the Filters Back in Place
a. Remove the pull-out drawer completely
and mount the grease filter so that it
covers the drawer.
b. Close the drawer and install the remaining
grease filter.
Active Carbon Filter
This filter eliminates the odours and vapours
which form during cooking.
When used in normal conditions it should be
replaced at intervals of 6-8 months.
These filter can be ordered from the supplier
The carbon filter cannot be washed or
regenerated.
To dismount the filter proceed as follows:
Press the two buttons C (fig. 3), pull the filter
slightly forwards and remove it.
Attention
Failure to observe the rules for cleaning the
appliance and changing and cleaning the
filters may cause fires.
Therefore, we recommend observing these
instructions.
Fixing the hood
Apply the scheme supplied (Nº 49A) on the
right of the cabinet so that the lines marked
by the arrows match the cabinet ensuring
that they meet at the back and under.
Make two Ø 2 mm holes at points 1 and
2 (fig. 4).
Carry out the same operation on the left.
Fix the hood to the cabinet using screws E
(4,5x16) supplied with the appliance (fig. 4).
Use the shim F supplied with the hood for 16
mm cupboard side panels.
Fit the shim F to the left and to the right of the
fixing curves of the hood and hook them in
the holes.
Adjusting the removable drawer
The hood may be mounted in cabinets with
different depths.
The back of the drawer can be adjusted so
that the front of the removable drawer is the
same depth as the cabinet.
Proceed as follows: unscrew the screws G,
move the square plates H as required and
tighten the screw G (fig. 5).
Operation
The hood model JDA 5330 is fitted with two
motors.
The speed of the motors is adjusted by
means of a 4-SPEED switch.
Use the high speed switch only in case of
high concentration of vapour.
The hood should be switched ON several
minutes before you start cooking and should
be allowed to run until all the vapours have
been eliminated.
The switching plate is fitted with two switches
one for continuous adjustment of the
Light switch
Speed switch
9
Replacing the lamps
— Disconnect the hood from the electricity.
— Opening the Light Cover Support (fig. 6)
a. Remove the pull-out drawer
completely.
b. Push the B knobs inwards toward
each other (in the “Open” direction as
indicated on the plastic knob itself).
— Always replace burnt-out lamps with olive
shaped lamps max 40Watts-E14.
— Re-close the light cover support.
— Before calling for Repair Service because
the hood fails to light up, make sure the
lamp is well-inserted.
Cleaning
To clean the outside of the hood use a cloth
moistened with denatured alcohol or neutral
liquid detergents.
Never use products containing abrasive.
Wipe brushed stainless steel in the same
direction as the brushing to avoid scratching.
10
ELECTROLUX HAUSGERÄTE GMBH
Rennbahnstraße 72-74
60528 Frankfurt L 921 Ed. 02/97
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Juno-Electrolux JDA5330W User manual
-
-
Hotpoint HC9X User manual
-
-
Electrolux EFS6331K User manual
-
Bosch Slimline cooker hood Operating instructions
-
ROSIERES RDR 91 BMV User manual
-
Alno AEF3620N User manual
-
-