Reftek Wrangler Quick start guide

Brand
Reftek
Model
Wrangler
Type
Quick start guide
For more information, visit
www.reftek.com
*107180-99-QS*
Setting up the recorder using the Ethernet and built-in web interface
1. As shipped from the factory, the recorder uses a link-local connection, which
allows its Ethernet cable to be plugged into any existing Ethernet network. The
Wrangler recorder defaults to a xed link-local IP address of 169.254.109.109.
NOTE – Only one factory default recorder can be connected to a network, until
the default IP address has been changed to a new, unique IP address.
2. Connect the Wrangler Ethernet cable to the recorder and to an Ethernet
network connection.
3. Apply power to the recorder using the power
cable.
4. From a computer on the same network as the
recorder, open a web browser and connect to
the Wrangler link-local IP address as follows:
http://169.254.109.109
5. Click PARAMETERS.
6. If this is the rst time logging into the unit,
you need to set the password for the admin
account. You should also set a password for
the user account at the same time.
7. Click NETWORK to open the Network
Settings screen.
8. Change the Wrangler’s IP address to be a
new unique IP address appropriate for your
Ethernet network.
9. Click Send at the bottom of the screen to send
the new network settings to the recorder.
ADDITIONAL INFORMATION
For full operating instructions, please refer to the Wrangler User Manual available
at www.reftek.com/wrangler.
Wrangler
SEISMIC RECORDER
Power
connector
Ethernet
connector
Wi-Fi antenna
connector
Unit ID
USB drive slot
Channel 4 - 6
input connector
Channel 1 - 3
input connector
Status LEDs
Magnetic switch
located under here
GPS connector
QUICK START GUIDE
© 2018–2019, Trimble Inc. All rights reserved. Trimble, and the Globe & Triangle logo are trademarks of Trimble Inc., registered in the United States and in other
countries. Google Play and the Google Play logo are trademarks of Google LLC. The Apple logo, iPhone, iPod touch, and iTunes Store are trademarks of Apple Inc.,
registered in the U.S. and other countries. All other trademarks are the property of their respective owners. P/N 107180-99-QS, Revision B, November 2019.
GETTING STARTED
TIP – Install the supplied O-ring around the outside of the USB well before securing
the USB cap. When power is applied to the Wrangler recorder, it takes less than 30
seconds for the recorder to automatically start and be fully operational.
Connect the Wrangler recorder to your local Ethernet network, by using either:
►
a smartphone/tablet and the Wrangler app
►
an Ethernet connection and the Wrangler’s built-in web interface
Setting up the recorder using the Wrangler app on a handheld device
1. Download the REF TEK Recorder Setup app from either Google Play or iTunes.
2. Apply power to the Wrangler recorder using the power cable.
TIP – Before continuing, install the Wi-Fi antenna on the SMA connector
located between the PWR and NET connectors.
3. After power-up, the Wi-Fi and LEDs stay on for at least 30 minutes before they
enter a low power mode. If the LEDs are o, briey wave the provided magnet
across the Wrangler label to turn the Wi-Fi on.
TIP – The magnetic sensor is located under
the REF TEK triangle (between the F and T in
REF TEK).
4. On your handheld device, go to the WiFi
settings and select the Wrangler_XXXXX
network for the recorder you are trying to
connect to (where XXXXX is the Unit ID
printed on the label above the status LED
window).
5. Exit the WiFi settings screen and run the REF
TEK Recorder Setup app on your handheld
device.
6. Once you see the Status screen, click
PARAMETERS.
7. If this is the rst time logging into the unit,
you need to set the password for the admin
account. You should also set a password for
the user account at the same time.
8. Click NETWORK to open the Network
Settings screen.
9. Change the Wrangler settings to match the
setup needed for your local Ethernet network.
You can now connect the recorder to your local Ethernet network.
WHAT’S IN THE BOX
►
Wrangler seismic recorder:
3 channels (P/N 109650-03) or
6 channels (P/N 109650-06)
►
Wi-Fi antenna and magnet for
DAS magnetic switch activation
(P/N 109650-90)
►
GPS cable: 10 m (P/N 113920-10), 20 m
(P/N 113920-20), 100 m (P/N 113920-100)
►
USB stick: 8 GB (P/N 97321-00),
16 GB (P/N 97321-16), 32 GB (P/N 97321-32)
►
Ethernet cable (P/N 101422-00)
OPTIONAL EXTRAS
►
GPS antenna (P/N 114650-00)
►
Power supply: either DC cable
(P/N 101419-00 gray) or AC cable
(P/N 101421-00 black).
2 3
  • Page 1 1
  • Page 2 2

Reftek Wrangler Quick start guide

Brand
Reftek
Model
Wrangler
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents