DFI HR100-CRM Owner's manual

HR100-CRM

System Board

User’s Manual

A1530

Copyright

This publication contains information that is protected by copyright. No part of it

may be reproduced in any form or by any means or used to make any transfor-

mation/adaptation without the prior written permission from the copyright hold-

ers.

This publication is provided for informational purposes only. The manufacturer

makes no representations or warranties with respect to the contents or use

of this manual and specifically disclaims any express or implied warranties of

merchantability or fitness for any particular purpose. The user will assume the

entire risk of the use or the results of the use of this document. Further, the

manufacturer reserves the right to revise this publication and make changes to

its contents at any time, without obligation to notify any person or entity of such

revisions or changes.

Changes after the publication’s first release will be based on the product’s revi-

sion. The website will always provide the most updated information.

Trademarks

All trademarks and registered trademarks of products appearing in this manual

are the properties of their respective holders.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission

limits.

1

4

Introduction

Table of Contents

Copyright ........................................................................................... 2

Trademarks ........................................................................................ 2

FCC and DOC Statement on Class B .............................................. 3

About this Manual ............................................................................. 6

Warranty .......................................................................................... 6

Static Electricity Precautions ............................................................. 7

Safety Measures ................................................................................. 7

About the Package ............................................................................ 8

Before Using the System Board ........................................................ 8

Chapter 1 - Introduction .................................................................. 9

Specifications .................................................................................. 9

Features ...................................................................................... 12

Chapter 2 - Hardware Installation .................................................. 15

System Board Layout .................................................................... 15

System Memory ........................................................................... 16

Installing the DIM Module ......................................................... 17

CPU ............................................................................................ 19

Installing the CPU .................................................................... 19

Installing the Fan and Heat Sink ................................................ 21

Jumper Settings ............................................................................. 23

Clear CMOS Data ..................................................................... 23

PS/2 Power Select .................................................................... 24

USB Power Select ..................................................................... 25

Panel Power Select ................................................................... 26

COM1/COM2 RS232/RS422/RS485 Select.................................... 27

COM1/COM2 RS232/Power Select............................................... 28

Power-on Select ....................................................................... 29

Rear Panel I/O Ports ..................................................................... 30

PS/2 Mouse and PS/2 Keyboard Ports ......................................... 31

COM (Serial) Ports ................................................................... 32

VGA Port ................................................................................. 33

DVI-I Port ............................................................................... 34

RJ45 LAN Ports ........................................................................ 35

USB Ports................................................................................ 36

Audio ...................................................................................... 38

I/O Connectors ............................................................................ 40

CD-in Internal Audio Connector ................................................. 40

S/PDIF Connector ..................................................................... 41

1

5

Introduction

LVDS LCD Panel Connector ........................................................ 42

LCD/Inverter Power Connector ................................................... 42

Digital I/O Connectors .............................................................. 44

SATA (Serial ATA) Connectors .................................................... 45

Cooling Fan Connectors ............................................................. 46

Chassis Instrusion Connector .................................................... 47

Power Connectors .................................................................... 48

Standby Power LED .................................................................. 50

Front Panel Connectors ............................................................. 51

Expansion Slots ....................................................................... 52

Battery ................................................................................... 55

CompactFlash Socket (optional) ................................................. 56

Chapter 3 - BIOS Setup .................................................................. 57

Overview .............................................................................................................. 57

AMI BIOS Setup Utility ................................................................. 59

Main ....................................................................................... 59

Advanced ................................................................................ 60

Chipset ................................................................................... 76

Boot ....................................................................................... 83

Security .................................................................................. 84

Save & Exit ............................................................................. 85

Updating the BIOS ........................................................................ 86

Notice: BIOS SPI ROM .................................................................. 87

Chapter 4 - Supported Software ................................................... 88

Chapter 5 - RAID ........................................................................ 115

RAID Levels .......................................................................................................115

Settings ................................................................................................................116

Chapter 6 - Intel AMT Settings ................................................... 120

Overview ............................................................................................................120

Enable Intel

®

AMT in the AMI BIOS ............................................................121

Enable Intel

®

AMT in the Intel

®

Management Engine BIOS

Extension (MEBX) Screen ..............................................................................

123

Appendix A - NLITE and AHCI Installation Guide ....................... 152

Appendix B - Watchdog Sample Code ......................................... 164

Appendix C - System Error Message ............................................ 165

Appendix D - Troubleshooting ...................................................... 167

1

6

Introduction

About this Manual

7KLV PDQXDO FDQ EH GRZQORDGHG IURP WKH ZHEVLWH RU DFTXLUHG DV DQ HOHFWURQLF

ILOH LQFOXGHG LQ WKH RSWLRQDO &''9' 7KH PDQXDO LV VXEMHFW WR FKDQJHDQGXS

GDWH ZLWKRXW QRWLFH DQG PD\ EH EDVHG RQ HGLWLRQV WKDW GR QRW UHVHPEOH \RXU

DFWXDO SURGXFWV 3OHDVH YLVLW RXU ZHEVLWH RU FRQWDFW RXU VDOHV UHSUHVHQWDWLYHV IRU

WKHODWHVWHGLWLRQV

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the

product, inability to use the product, unauthorized replacement or alteration

of components and product specifications.

2. The warranty is void if the product has been subjected to physical abuse,

improper installation, modification, accidents or unauthorized repair of the

product.

3. Unless otherwise instructed in this user’s manual, the user may not, under

any circumstances, attempt to perform service, adjustments or repairs on the

product, whether in or out of warranty. It must be returned to the purchase

point, factory or authorized service agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial

damages to the product that has been modified or altered.

1

7

Introduction

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components

or devices even before installing them in your system unit. Static electrical dis-

charge can damage computer components without causing any signs of physical

damage. You must take extra care in handling them to ensure against electro-

static build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag

until y

ou are ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the compo-

nents, contacts or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold

modules or connectors by their ends.

Important:

Electrostatic discharge (ESD) can damage your processor

, disk drive and

other components. Perform the upgrade instruction procedures described

at an ESD workstation only. If such a station is not available, you can

provide some ESD protection by wearing an antistatic wrist strap and

attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for instal-

lation or servicing. After installation or servicing, cover the system chassis

before plugging the power cord.

Battery:

• Danger of explosion if battery incorrectly replaced.

• Replace only with the same or equivalent type recommend by the manufac-

turer.

• Dispose of used batteries according to local ordinance.

1

8

Introduction

About the Package

The system board package contains the following items. If any of these items are

missing or damaged, please contact your dealer or sales representative for as-

sistance.

; One HR100-CRM motherboard

; Two Serial ATA data cables

; Two Serial ATA power cables

; Two USB cables

; One bracket mounted with a COM port cable

; One I/O shield

; One QR (Quick Reference)

Optional Items

; USB port cable

; COM port cable

; Serial ATA data cable

; Serial ATA power cable

; I/O shield

The system board and accessories in the package may not come similar to the

information listed above. This may differ in accordance to the sales region or

models in which it was sold. For more information about the standard package in

your region, please contact your dealer or sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

1

9

Introduction

Processor

Chipset

System Memory

Expansion Slots

Graphics

Chapter 1 - Introduction

• Socket G2 988B for:

- 3rd Generation Intel

®

Core™ processors

(22nm process technology) (Rev. AG0 or later)

: Intel

®

Core™ i7-3610QE (6M Cache, up to 3.3 GHz); 45W

: Intel

®

Core™ i5-3610ME (3M Cache, up to 3.3 GHz); 35W

: Intel

®

Core

TM

i3-3120ME (3M Cache, 2.4GHz); 35W

- 2nd Generation Intel

®

Core™ processors

(32nm process technology)

: Intel

®

Core™ i7-2710QE (6M Cache, up to 3.0 GHz); 45W

: Intel

®

Core™ i5-2510E (3M Cache, up to 3.1 GHz); 35W

: Intel

®

Core

TM

i3-2330E (3M Cache, 2.2 GHz); 35W

: Intel

®

Celeron

®

B810 (2M Cache, 1.6 GHz); 35W

• Intel

®

Advanced Vector Extensions (Intel

®

AVX) Instructions

• Intel

®

Turbo Boost Technology

• Intel

®

QM67 Express Chipset

• Two 204-pin DDR3 SODIMM sockets

• Supports DDR3 1333/1600MHz (3rd generation processors)

Supports DDR3 1066/1333MHz (2nd generation processors)

• Supports dual channel memory interface

• Supports up to 16GB system memory

• DRAM device technologies: 1Gb, 2Gb and 4Gb DDR3 DRAM

technologies are supported for x8 and x16 devices, unbuf-

fered, non-ECC

• 1 PCIe x16 slot

- Supports Gen 3.0 (3rd generation processors)

- Supports Gen 2.0 (2nd generation processors)

- Switchable with SDVO/HDMI/DP

- Configurations (supported only via a riser card):

: One x8 (GFX) and two x4 (I/O)

: Two x8 (GFX, I/O)

: One x16 (GFX, I/O)

• 2 DFI Proprietary Extension bus for

PCIe/PCI expansion

• 1 CompactFlash socket (optional)

• Intel

®

HD Graphics

• Display ports: DVI-D (ASMedia 1442), LVDS and VGA

• DVI: resolution up to 1920x1200 @60Hz

• LVDS: Single Channel - 18/24-bit; Dual Channel: 36/48-bit

,

resolution up to 1920x1200 @60Hz

• VGA: resolution up 2048x1536 @75Hz

• Supports 6 Graphics Execution Units (EUs)

• Intel

®

Clear Video Technology

• DirectX Video Acceleration (DXVA) support for accelerating

video processing

Specifications

1

10

Introduction

Audio

LAN

Serial ATA

CompactFlash

Intel Active

Management

Technology

(AMT)

TPM (optional)

Rear Panel I/O

Ports

Energy Efficient

Design

• Realtek ALC262 2-channel High Definition Audio

•

High performance DACs with 100dB SNR

• ADCs with 90dB SNR

• Two stereo DACs support 24-bit PCM format for stereo au-

dio playback

• Three stereo ADCs support 20-bit PCM format for multiple

input streaming

• S/PDIF audio interface

• Intel

®

82579LM with iAMT7.0 Gigabit Ethernet Phy

• Realtek RTL8111DL PCI Express Gigabit Ethernet controller

• Integrated 10/100/1000 transceiver

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

• 4 Serial ATA ports

- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s

- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s

• Integrated Advanced Host Controller Interface (AHCI) con-

troller

• Supports RAID 0/1/5/10

• JMicron JMB368 PCI Express to PATA host controller

• DMA mode: Ultra ATA up to 100MB/s

• PIO mode: up to 16MB/s

• Supports iAMT7.0

• Out-of-band system access

• Remote troubleshooting and recovery

• Hardware-based agent presence checking

• Proactive alerting

• Remote hardware and software asset tracking

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement and pass-

word protection

• 1 mini-DIN-6 PS/2 mouse port

• 1 mini-DIN-6 PS/2 keyboard port

• 2 DB-9 serial ports

- Supports RS232/422/485

- Pins 1 and 9 of RS232 functions as RS232 signal or power

(selectable via jumper)

• 1 DB-15 VGA port

• 1 DVI-I port (DVI-D signal)

• 2 RJ45 LAN ports

• 4 USB 2.0/1.1 ports

• Mic-in, Line-in and Line-out jacks

• Supports ErP Lot6 power saving (optional)

• Supports ACPI

• System Power Management

• Wake-On-Events include:

- Wake-On-PS/2 KB/Mouse

- Wake-On-USB KB/Mouse

- Wake-On-LAN

- RTC timer to power-on the system

• CPU stopped clock control

• AC power failure recovery

1

11

Introduction

I/O Connectors

Damage Free

Intelligence

BIOS

Power

Consumption

OS Support

Temperature

Humidity

Dimensions

Certification

• 2 connectors for 4 external USB 2.0/1.1 ports

• 4 connectors for 4 external RS232 serial ports

• 1 L

VDS LCD panel connector

• 1 LCD/inverter power connector

• 1 8-bit Digital I/O connector

• 1 front audio connector for line-out and mic-in jacks

• 1 S/PDIF connector

• 4 Serial ATA ports

• 1 24-pin ATX power connector

• 1 chassis intrusion connector

• 1 front panel connector

• 2 fan connectors

• Monitors CPU/system temperature and overheat alarm

• Monitors VCORE/5V/1.05V/1.5V/12V/3.3V/VBAT voltages

and failure alarm

• Monitors CPU/system fan speed and failure alarm

• Read back capability that displays temperature, voltage and

fan speed

• Watchdog timer function

• AMI BIOS

- 64Mbit SPI BIOS

• 64.68 W with i7-2710QE at 2.1GHz and 2x 4GB DD3 SO-

DIMM

• Windows XP Professional x86 & SP3 (32-bit)

• Windows XP Professional x64 & SP2 (64-bit)

• Windows 7 Ultimate x86 & SP1 (32-bit)

• Windows 7 Ultimate x64 & SP1 (64-bit)

• Windows 8 Enterprise x86 (32-bit)

• Windows 8 Enterprise x64 (64-bit)

• 0

o

C to 60

o

C

• 10% to 90%

• Mini-ITX form factor

- 170mm (6.7”) x 170mm (6.7”)

• Heat spreader with heat sink and fan

- 62mm x 60mm x 42mm

• CE, FCC Class B, UL, RoHS

1

12

Introduction

Features

Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the sys-

tem at the set time interval. If the system hangs or fails to function, it will reset

at the set time interval so that your system will continue to operate.

DDR3

DDR3 delivers increased system bandwidth and improved performance. It offers

peak data transfer rate of up to 16Gb/s bandwidth. The advantages of DDR3

are its higher bandwidth and its increase in performance at a lower power than

DDR2.

Graphics

The integrated Intel HD graphics for graphics intensive applications delivers ex-

ceptional 3D, 2D and video capabilities. It supports VGA, DVI-D and LVDS inter-

faces.

DVI

DVI (Digital Visual Interface) is a form of video interface technology made to

maximize the quality of flat panel LCD monitors and modern video graphics

cards. Data is transmitted using the TMDS (Transition Minimized Differential Sig-

naling) protocol, providing a digital signal from the PC’s graphics subsystem to

the display.

PCI Express

PCI Express is a high bandwidth I/O infrastructure that possesses the ability to

scale speeds by forming multiple lanes. The PCI Express architecture provides a

high performance graphics infrastructure by enhancing the capability of a x16 PCI

Express lane to provide 4 Gigabytes per second transfer rate.

Intel Active Management Technology (AMT)

Intel Active Management Technology (Intel

®

AMT) allows remote access and man-

agement of networked systems even while PCs are powered off, remotely repair

systems after OS failures and has the capability to remotely update all systems

with the latest security software.

Audio

The Realtek ALC262 audio codec provides 2-channel High Definition audio output.

1

13

Introduction

Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specifica-

tion. SATA 3.0 supports speed up to 6Gb/s while SATA 2.0 supports speed up to

3Gb/s. This improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s. The board supports RAID 0/1/5/10.

Gigabit LAN

The Intel W82579LM PHY and Realtek RTL8111DL PCI Express Gigabit controllers

support up to 1Gbps data transmission.

CompactFlash (optional)

The CompactFlash

TM

socket is used for inserting a CompactFlash

TM

card. Compact-

Flash

TM

card is a small removable mass storage device designed with flash tech-

nology - a non-volatile storage solution that does not require a battery to retain

data indefinitely. The CompactFlash

TM

technology is widely used in products such

as portable and desktop computers, digital cameras, handheld data collection

scanners, PDAs, Pocket PCs, handy terminals and personal communicators.

USB

The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/

second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a

marked improvement in device transfer speeds between your computer and a

wide range of simultaneously accessible external Plug and Play peripherals.

Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-

Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses

the PCI PME (Power Management Event) signal. However, if your system is in the

Suspend mode, you can power-on the system only through an IRQ or DMA inter-

rupt.

Important:

The 5V_standby power source of y

our power supply must support

720mA.

Wake-On-PS/2

This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on

the system.

Important:

The 5V_standby power source of y

our power supply must support

720mA.

1

14

Introduction

Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a sys-

tem from the S3 (STR - Suspend To RAM) state.

Important:

If y

ou are using the Wake-On-USB Keyboard/Mouse function for 2 USB

ports, the 5V_standby power source of your power supply must support

1.5A. For 3 or more USB ports, the 5V_standby power source of your

power supply must support 2A.

RTC Timer

The RTC installed on the system board allows your system to automatically pow-

er-on on the set date and time.

ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and

Power Interface) specification. ACPI has energy saving features that enables PCs

to implement Power Management and Plug-and-Play with operating systems that

support OS Direct Power Management. ACPI when enabled in the Power Manage-

ment Setup will allow you to use the Suspend to RAM function.

With the Suspend to RAM function enabled, you can power-off the system at

once by pressing the power button or selecting “Standby” when you shut down

Windows

®

without having to go through the sometimes tiresome process of

closing files, applications and operating system. This is because the system is

capable of storing all programs and data files during the entire operating session

into RAM (Random Access Memory) when it powers-off. The operating session will

resume exactly where you left off the next time you power-on the system.

Important:

The 5V_standby power source of y

our power supply must support

t720mA.

Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-

on the system manually or let the system power-on automatically.

15

2

Hardware Installation

System Board Layout

Chapter 2 - Hardware Installation

PS/2 Mouse

PS/2 KB

COM 2

COM 1

DVI-I port

(D

VI-D signal only)

VGA

DVI-I

LAN 1 (Intel)

USB 1

USB 0

LAN 2 (Realtek)

USB 9

USB 8

Mic-in

Line-in

Line-out

1

PS/2 power

select (JP2)

1

5

COM1 RS232/Power

select (JP1)

2

6

JP1

1

5

2

6

JP3

COM2 RS232/Power

select (JP3)

1

2

5

6

JP4

1

2

5

6

JP5

COM1 RS232/422/485

select ( )JP4

COM2 RS232/422/485

select ( )JP5

ASMedia

1442

1

CPU fan

DDR3_1 SODIMM

DDR3_2 SODIMM

COM6

1

2

9

COM5

1

2

9

COM4

1

2

9

COM3

1

2

9

13

12

24

1

ATX Power

Power-on

select ( )JP7

1

Chassis

intrusion

DIO

1

2

19

1

11

Front

panel

Standby

Power LED

SPI Flash

BIOS

1

System fan

Battery

USB 0-1, 8-9 power

select (JP6)

1

Realtek

ALC262

Front audio

1

CD-in

S/PDIF

1

2

9

10

Intel

QM67

SATA 4

1

SATA 5

1

SATA 0

1

SATA 1

1

9

10

USB 2-3

9

USB 4-5

Clear CMOS

(JP10)

1

Panel power

select ( )JP9

2

5

6

1

LCD/Inverter

power

LVDS LCD

panel

40 39

21

PCIE x16

PCIE x1 PCIE x1

1

2

1

2

SATA 3.0

SATA 2.0

Socket G2

rPGA 988B

1

CF Card Setting

(JP8)

16

2

Hardware Installation

System Memory

Important:

Electrostatic discharge (ESD) can damage your system board, processor,

disk drives, add-in boards, and other components. Perform the upgrade

instruction procedures described at an ESD workstation only. If such a

station is not available, you can provide some ESD protection by wearing

an antistatic wrist strap and attaching it to a metal part of the system

chassis. If a wrist strap is unavailable, establish and maintain contact

with the system chassis throughout any procedures requiring ESD pro-

tection.

DDR3-2

DDR3-1

Standby

Power LED

Important:

When the Standby Power LED lit red, it indicates that there is power on

the system board. Power-off the PC then unplug the power cord prior to

installing any devices. Failure to do so will cause severe damage to the

motherboard and components.

Features

• Two 204-pin DDR3 SODIMM sockets

• Supports 1066/1333MHz DDR3 SDRAM

• Dual channel memory interface

• Supports maximum of 16GB system memory

17

2

Hardware Installation

Note:

The system board used in the following illustrations may not resemble

the actual board. These illustrations are for reference only.

Installing the DIM Module

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Locate the DIMM socket on the system board.

4. Push the “ejector tabs” which are at the ends of the socket to the side.

Ejector tab

5. Note how the module is keyed to the socket.

Key

Notch

18

2

Hardware Installation

7. Seat the module vertically, pressing it down ¿ rmly until it is completely seat-

ed in the socket. The ejector tabs at the ends of the socket will automatically

snap into the locked position to hold the module in place.

6. Grasping the module by its edges, position the module above the socket with

the “notch” in the module aligned with the “key” on the socket. The keying

mechanism ensures the module can be plugged into the socket in only one

way.

19

2

Hardware Installation

CPU

Overview

The system board is equipped with a surface mount PGA 988B CPU socket.

Note:

The system board used in the following illustr

ations may not resemble

the actual one. These illustrations are for reference only.

Installing the CPU

1. Make sure the PC and all other peripheral devices connected to it has been

powered down.

2. Disconnect all power cords and cables.

3. Locate the PGA 988B sock-

et on the system board.

4. Make sure the screw is in

its unlock position. If it’s

not, use a screwdriver to

turn the screw to its un-

lock position.

Lock

Unlock

20

2

Hardware Installation

5. Position the CPU above the

socket. The gold triangular

mark on the CPU must

align with pin 1 of the CPU

socket.

Important:

Handle the CPU by its edg-

es and a

void touching the

pins.

Pin 1

Gold triangular mark

6. Insert the CPU into the

socket until it is seated

in place. The CPU will ¿ t

in only one orientation

and can easily be inserted

without exerting any force.

Use a screwdriver to turn

the screw to its lock posi-

tion.

Important:

Do not force the CPU into

the sock

et. Forcing the

CPU into the socket may

bend the pins and damage

the CPU.

Screw in locked

position

Page is loading ...

DFI HR100-CRM Owner's manual

This manual is also suitable for

DFI HR100-CRM Owner's manual

Related papers

Other documents