i3 International CMS Connections Quick start guide

Type
Quick start guide
Rev. 180913
1
CMS Connections Quick Guide
CMS Web 5
Overview
This document will explain the necessary connections and set up for CMS
clients.
Please Note: Before installation it must be decided which ports will be
open for data exchange between the client and the CMS. CMS requires
one of these ports to be opened. Which port will depend on the needs of
the client. The address of the domain will depend on the choice of port.
Port 80: Unsecured data transfer over the internet. The domain
name will begin with http://
Port 443: Secure data transfer over the internet. The domain
name will begin with https://
PAC Converter Installation
The PAC Converter is needed for
the CMS v5.x. The converter can be
obtained from i3 international’s
Website at: https://i3international.
com/support/download, or it
can be found on the NVR in the Do
Not Delete folder on D:// drive.
Please Note that there is a 32bit PAC
Converter for SRX Pro v3.3.3.69 and
a 64bit PAC Converter for SRX-Pro
v5.x. Be sure to select the correct
PAC Converter.
1. Download or transfer PAC
Converter to the Root of D://
drive
2. Install PAC Converter
3. Open “PAC Converter Configuration” and allow it to auto update to the
latest version.
Once PAC Converter is installed and opened it should look like this.
4. Click the CMS Web Server Tab and enter the domain address to the
“Service URL (IP:Port)” input box and click save. It will be necessary to
substitute your domain name where it says DOMAIN NAME in the example
below. Your domain name and the address will have been provided to you
by i3’s CMS Team.
5. Please Note: The address must contain the http:// or https:// as shown
above. It will depend on which port has been opened as to which address
is used. Port 80: http:// or Port 443: https://.
6. Test the connection by clicking on the Test Connection Button. If it does not
succeed check the URL and try again. Click Save.
SRX-Pro Setup
Open and log into SRX-Pro on the NVR and click on the Communication tab.
What is displayed under the communications tab depends on the version of
SRX-Pro that you are running.
Follow these instructions for SRX-Pro Versions 3.3.3.69 and above.
Under CMS Settings, click on “CMS information” button.
Change the Domain name to https://i3care.i3international.com/
Domain Name/ (this will be the exact address that was entered into PAC
Converter earlier, depending on which port is being used the address will
begin with either http:// or https://. Enter the Company name and e-mail
address in the appropriate fields and click the large blue “I Agree” button
Please Note the Domain Name is the domain given you from the CMS team.
i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
Canada 780 Birchmount Road, Unit 16,
Scarborough, ON, M1K 5H4
U.S.A 4450 Witmer Industrial Estates Unit 4
Niagara Falls, NY 14305
CMS Connections Quick Guide
Follow these instructions for SRX-Pro Versions older then 3.3.3.69.
Open and log into SRX-Pro on the NVR and click on the Communication tab.
Under CMS Settings enter the Loopback IP number which is the local PC IP.
This number will always be 127.0.0.1
Also on the Communication tab ensure the “Connect to CMS Server” is
checked and enter the Public Address of the DVR in the input box.
CMS WEB Configuration
To configure the CMS WEB open an internet browser on any computer capable of
accessing the internet and follow these instructions.
1. Enter the URL; www.i3care.i3international.com/DOMAIN NAME/
The Domain Name is the one give to you by i3’s CMS team.
2. Login with the admin user name and password you received from i3’s CMS
team.
3. Once the CMS WEB application opens
click on the Configurations button on the
Left hand navigation bar and select Site
Administrator.
4. In the center display area click “Add” and
select “Add Region”. This can be the State /
Province (or follow company region policy)
where the store is located.
Select the region you just created and click “Add” again and select “Add
Site” and fill out the required fields in the Site Window that opens up.
5. Select the DVR/NVR by serial number to be associated with this site.
Repeat these steps for each Region, location, and DVR.
CMS User Groups Creation
Groups are used to define the permissions for users.
1. To create a new Group for user permissions select Groups from the
Configurations menu.
2. Name the Group and select which CMS modules this group will have
access to from the list.
3. Select which existing users should belong
to this group. Each user can only belong to
one group.
CMS User Creation
To create a user for CMS Web please follow these
instructions.
1. Select “Users” from the Configurations Menu.
2. Click the Add button from the top of the form.
3. Enter the user’s information in the required
fields. Please remember to select from the
list of available sites on the right hand side
the locations the user will have access too.
4. Please Note that the Group Name field defines what permissions the user
has access too. It may be necessary to create a new group to facilitate
the new user.
5. Don’t forget to click save in the bottom right.
If at any time you experience any problems with the CMS connection process
please contact i3’s CMS team for assistance. The CMS team can be reached
at: 1.866.840.0004. Select select Technical Support Option from the phone
menu.
  • Page 1 1
  • Page 2 2

i3 International CMS Connections Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI