Sanus NF206 Installation guide

Sanus
Brand
Sanus
Model
NF206
Type
Installation guide

Sanus NF206 is a sturdy and versatile piece of furniture that can be used in a variety of settings, from home offices to living rooms. With its sleek design and durable construction, the NF206 is sure to complement any décor. The NF206 features multiple shelves, providing ample space for storage and display. The shelves are made of tempered glass, which is strong and easy to clean. The NF206 also includes a number of features that make it easy to organize and manage your cables, including wire straps and plastic wire covers.

Sanus NF206 is a sturdy and versatile piece of furniture that can be used in a variety of settings, from home offices to living rooms. With its sleek design and durable construction, the NF206 is sure to complement any décor. The NF206 features multiple shelves, providing ample space for storage and display. The shelves are made of tempered glass, which is strong and easy to clean. The NF206 also includes a number of features that make it easy to organize and manage your cables, including wire straps and plastic wire covers.

Assembly Instructions for Natural Furniture: Model NF206
Thank you for choosing the Natural Furniture line from Sanus Systems. If you have any questions
regarding this or any other Sanus Systems product, contact us at 800.359.5520 or visit us at
www.sanus.com. Our customer service representatives will assist you with any issues regarding
assembly or missing parts. Check to make sure none of the parts are missing or defective. Never
use defective parts. Replacement parts for products purchased from an authorized dealer will be
shipped directly to you. Please call Sanus Systems before returning products to retail stores.
Supplied Parts List: (Not to Scale)
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113
800.359.5520 www.sanus.com 05.12.06 (100038)
Front Frame - A
Qty. 1
Rear Frame - B
Qty. 1
Glass Top Shelf - C
Qty. 1
Glass Mid Shelf - D
Qty. 5
Cross Tube - E
Qty. 6
Cross Tube W/ Stud - F
Qty. 4
Plastic Wire Cover
30 in - G
Qty. 1
Plastic Wire Cover
21 in - H
Qty. 1
Wire Strap - I
Qty. 2
Three Hole Plate - J
Qty. 4
1.5 in. Washer - O
Qty. 6
Decorative Face Bolt - N
Qty. 6
Supplied Hardware: (Full Size)
1 in. Washer - L
Qty. 8
Allen Key - M
Qty. 1
Glass Protector - P
Qty. 4
Step 1: Attach Cross Tubes to Front Frame
NOTE: For ease of assembly, lay the Front Fame face down on a soft at surface after inserting the six Decorative
Face Bolts.
Insert six Decorative Face Bolts (N) through the Front Frame (A). Slide a Three Hole Plate (J) over the Decorative Face
Bolts; then, screw a Cross Tube (E) onto each Decorative Face Bolt, rmly hand tighten each Cross Tube.
Diagram 1
N
J
E
A
Allen Bolt - K
Qty. 10
Step 2: Attach Cross Tubes W/Stud to Front Frame
Place a 1 inch Washer (L) on the threaded stud of each Cross tube W/Stud (F) and screw them into the Front Frame (A).
Firmly hand tighten each Cross Tube W/Stud.
Diagram 2
F
L
A
Step 3: Attach Rear Frame to Front Frame and Cross Tubes
With The Cross Tubes still facing up, and the Front Frame (A) still on a soft, at surface. Place a 1 inch Washer (L) on each
Cross tube W/Stud (F) and a Three Hole Plate (J) on the remaining Cross Tubes (E).
NOTE: Horizontal grooves in the Rear Frame must be facing the Front Frame and the three holes closest to the
edge of the Rear Frame must be aligned toward the top of the Front Frame.
Align the holes in the Rear Frame (B) with the holes in the Cross Tubes; then, using a 1.5 inch Washer (O) and Allen
Bolt (K), secure the Rear Frame to the Cross Tubes W/Studs (F) using the Allen Key (M).
Using 1.5 inch Washer (O) and Allen Bolt (K), secure the Rear Frames to the two center Cross Tubes (E) using the Allen
Key (M).
Using Allen Bolts (K) and Allen Key (M), secure the two Wire Straps (I) to the Rear Frame.
Diagram 3
E
J
O
K
I
K
F
L
O
K
Three holes near
edge toward top.
Groove
Three holes
furthest from
edge toward
Bottom.
E
J
O
K
I
K
L
O
K
Horizontal
Groove
F
Step 4: Glass Mid Shelf Installation
NOTE: Make sure the round edges of the Glass Shelves are to the sides and the at edge ts into the groove in the
Front and Rear Frame.
Slide each Glass Mid Shelf (D) through the front of the Front Frame (A) until it is fully into the groove in the Rear Frame (B);
then, lower it onto the ledge on the back side of the Front Frame.
Diagram 4
D
B
A
Groove in Rear Frame
Step 5: Glass Top Shelf Installation
Evenly place two Glass Protectors (P) on the top of the Front Frame (A) and two on the Rear Frame (B); then place the Top
Glass Shelf (C) on the Glass Protectors on the Front and Rear Frames.
Diagram 5
P
C
A
P
B
Step 6: Plastic Wire Cover Installation
After the desired components have been placed on the Glass Shelves (C & D) and the cables routed through the Wire
Straps (I), install the two Plastic Wire Covers (G & H) by inserting one side into a groove in the back of the Rear Frame (B);
then, snapping the other side of the Plastic Wire Cover into the grove on the other side of the Rear Frame as shown in Top
View.
Diagram 6
Top View
I
I
G
H
Plastic Wire Cover
Grooves in
Rear Frame (B)
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113
800.359.5520 www.sanus.com 05.12.06 (100038)
B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Sanus NF206 Installation guide

Sanus
Brand
Sanus
Model
NF206
Type
Installation guide

Sanus NF206 is a sturdy and versatile piece of furniture that can be used in a variety of settings, from home offices to living rooms. With its sleek design and durable construction, the NF206 is sure to complement any décor. The NF206 features multiple shelves, providing ample space for storage and display. The shelves are made of tempered glass, which is strong and easy to clean. The NF206 also includes a number of features that make it easy to organize and manage your cables, including wire straps and plastic wire covers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents