Contents
New Functions in MONTAGE Version 1.60 .............................................................................. 2
Additional New Effect Types ............................................................................................................................. 3
Additional New Performances........................................................................................................................... 4
Motion Control................................................................................................................................................... 5
Common/Audio Edit (Common/Audio).............................................................................................................. 6
Part Edit (Edit)................................................................................................................................................... 8
New Functions in MONTAGE Version 1.50 .............................................................................. 9
Additional New Effect Types ........................................................................................................................... 10
Additional New Performances......................................................................................................................... 12
Category Search ............................................................................................................................................. 13
Performance Play (Home) .............................................................................................................................. 15
Motion Control................................................................................................................................................. 19
Utility ............................................................................................................................................................... 20
Edit.................................................................................................................................................................. 27
New Functions in MONTAGE Version 1.20 ............................................................................ 28
Motion Control................................................................................................................................................. 29
Play/Rec.......................................................................................................................................................... 30
Category Search ............................................................................................................................................. 32
Utility ............................................................................................................................................................... 33
Common/Audio Edit (Common/Audio)............................................................................................................ 35
Part Edit (Edit)................................................................................................................................................. 37
New Functions in MONTAGE Version 1.10 ............................................................................ 39
New Performances ......................................................................................................................................... 40
Performance Play (Home) .............................................................................................................................. 40
Category Search ............................................................................................................................................. 41
Utility ............................................................................................................................................................... 43
Part Edit (Edit)................................................................................................................................................. 46
Live Set Edit (Edit) .......................................................................................................................................... 47
Live Set ........................................................................................................................................................... 48
MUSIC SYNTHESIZER
EN
Supplementary Manual
MONTAGE Supplementary Manual
2
New Functions in MONTAGE Version 1.60
Yamaha has upgraded the MONTAGE firmware, adding the following new functions.
This manual describes additions and changes with respect to the Reference Manual that came with your instrument.
• New effect types have been added.
• New Performances have been added.
• New functions have been added in some displays for simplifying Super Knob settings.
MONTAGE Supplementary Manual
3
Additional New Effect Types
The MONTAGE offers following new effect types.
Effect Type Description Parameter Description
Spiralizer P,
Spiralizer F
Unique filter applying
Phaser (for Spiralizer
P)/ Flanger (for
Spiralizer F)
processing with
seemingly endless up/
down pitch change.
Spiral Speed Determines the speed of the pitch shift.
Offset Determines the starting pitch in semitones.
Feedback Determines the level of the sound signal output from the effect block and
returned to its own input.
Step Mode Determines whether the pitch shifts smoothly or step by step.
Semitones Determines the pitch shift range when “Step Mode” is set to “Semitone.”
Scale Type Determines how the pitch changes when “Step Mode” is set to “Scale.”
Spiral Sync Determines the basic time period over which the pitch shifts step by step.
Ofs Transition Determines the time that elapses after the Offset value changes.
Step Transition Determines how long it takes for the pitch to change to the next pitch
when the pitch shifts step by step.
Dry/Wet Determines the balance of the dry sound and the effect sound.
Spiral Turn the LFO On/Off.
Effect Type Description Parameter Description
Tempo Spiralizer P,
Tempo Spiralizer F
Spiralizer with tempo-
synchronized LFO.
Spiral Speed Determines the speed of the pitch shift.
Offset Determines the starting pitch in semitones.
Feedback Determines the level of the sound signal output from the effect block and
returned to its own input.
Step Mode Determines whether the pitch shifts smoothly or step by step.
Semitones Determines the pitch shift range when “Step Mode” is set to “Semitone.”
Scale Type Determines how the pitch changes when “Step Mode” is set to “Scale.”
Spiral Sync Determines the basic time period over which the pitch shifts step by step.
Ofs Transition Determines the time that elapses after the Offset value changes.
Step Transition Determines how long it takes for the pitch to change to the next pitch
when the pitch shifts step by step.
Dry/Wet Determines the balance of the dry sound and the effect sound.
Direction Determines the direction of the pitch shift.
Spiral Turn the LFO On/Off.
MONTAGE Supplementary Manual
4
Additional New Performances
The MONTAGE offers 8 new Performances.
For the added Performances, refer to the Data List.
MONTAGE Supplementary Manual
5
Motion Control
Shortcut buttons have been added for simplifying Super Knob settings.
Edit Super Knob Motion Seq (Edit Super Knob Motion Sequencer)
Calls up the Knob Auto display for editing the Motion Sequencer applied to the Super Knob (Super Knob Motion Sequencer).
Edit Super Knob
Calls up the Control Assign display in Common/Audio Edit for setting parameters controlled with the Super Knob.
Motion Control
Super Knob
Operation
[PERFORMANCE] [Motion Control] [Super Knob]
Edit Super Knob Motion Seq (Edit Super Knob Motion Sequencer)
Edit Super Knob
MONTAGE Supplementary Manual
6
Common/Audio Edit (Common/Audio)
You can now set Super Knob to “Display Filter.” You can also check the parameters for Parts which are controlled by using
Assignable Knobs common to all Parts in this display.
Display Filter
Determines the Controller to be displayed. When “Super Knob” is selected, all Assignable Knob settings in which “Super Knob
Link” is set to On are displayed.
Settings: AsgnKnob 1 – 8, Super Knob, MS Lane 1 – 4, EnvFollow 1 – 16, EnvFollowAD, EnvFollowMst, All
The following parameters are displayed only when “Destination 1 – 16” is set to “Part 1 – 16 Assign 1 – 8.” Also, when
Destination is not set to any Assignable Knobs for the Part, only the shortcut buttons are available.
Destination
Determines the controller settings for the Part to be displayed.
Settings: 1 – 16 (The number of Destinations for the Assignable Knobs for the Part which is selected in “Destination 1 – 16” is displayed.)
Parameter
Determines the parameters for the Part to be controlled.
Settings: Refer to the “Control List” in the Data List.
Edit Part Control Settings
Calls up the Control Assign display for the currently selected Part.
Curve Type
Determines the specific curve for changing the parameter which is set in “Destination.” The horizontal axis indicates the value of
the controller set in “Source” and the vertical axis indicates the parameter values.
Settings: Standard, Sigmoid, Threshold, Bell, Dogleg, FM, AM, M, Discrete Saw, Smooth Saw, Triangle, Square, Trapezoid, Tilt Sine, Bounce,
Resonance, Sequence, Hold
For User Bank: User 1 – 32
When a Library file is read: Curves in Library 1 – 8
Control
Control Assign
Operation
[PERFORMANCE] [EDIT] PART [COMMON] [Control] [Control Assign]
or
Touch [Edit Super Knob] in the Super Knob display.
Display Filter
MONTAGE Supplementary Manual
7
Polarity (Curve Polarity)
Determines the Curve Polarity of the Curve type set in “Curve Type.”
Settings: Uni, Bi
Uni: Unipolar changes only in a positive direction or in a negative direction from a base parameter value according to the Curve shape.
Bi: Bipolar changes in both of positive and negative directions from a base parameter value.
Ratio (Curve Ratio)
Determines the Curve Ratio.
Settings: -64 – +63
MONTAGE Supplementary Manual
8
Part Edit (Edit)
You can now set Super Knob to “Display Filter.”
Display Filter
Determines the Controller to be displayed. When “Super Knob” is selected, all Assignable Knob settings to be affected by using
the Super Knob are displayed.
Settings: PitchBend, ModWheel, AfterTouch, FootCtrl 1, FootCtrl 2, FootSwitch, Ribbon, Breath, AsgnKnob 1 – 8, Super Knob, AsgnSw 1, AsgnSw 2,
MS Lane 1 – 4, EnvFollow 1 – 16, EnvFollowAD, EnvFollowMst, All
Edit Common Control Settings
Calls up the Control Assign display for Common/Audio Edit.
Mod/Control (Modulation/Control)
Control Assign
Operation
[PERFORMANCE] [EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Mod/Control] [Control Assign]
Edit Common Control Settings
Display Filter
MONTAGE Supplementary Manual
9
New Functions in MONTAGE Version 1.50
Yamaha has upgraded the MONTAGE firmware, adding the following new functions.
This manual describes additions and changes with respect to the Reference Manual that came with your instrument.
• New effect types have been added.
• New Performances have been added.
• The Favorite function has been added.
• “Mixing” has been added for the “Parameter with Part” setting of the Part Category Search.
• From the Performance Play (Home) display, you can now see various information.
• The Super Knob Link function has been added.
• You can now control the monitor volume of the Audio signal input from the [USB TO HOST] terminal.
• You can now switch Scenes by Control Change messages.
• You can now make partial changes to the font size on the Live Set display and the Category Search display.
• You can now save/load backup files in which the entire User Memory data (including Songs and Libraries) is stored.
• Each Edit display has been improved by allowing touch selection of Parts from the display.
MONTAGE Supplementary Manual
10
Additional New Effect Types
The MONTAGE offers following new effect types.
Effect Type Description Parameter Description
Rotary Speaker 2 Simulator of a rotary
speaker including
the amp block.
Speed Control Switches the rotary speed.
Drive Controls the amount of the distortion.
Tone Adjusts the tone level.
R/H Balance Determines the volume balance of the horn (higher range) and rotor (lower range).
Output Level Determines the output level of the effected sounds.
Mic L-R Angle Determines the L/R angle of the microphone.
Input Level Determines the input level.
Mod Depth Determines the depth of the modulation.
Horn Slow/Fast Determines how long it takes for the rotation speed of the horn (higher range) to change from
Slow to Fast when the rotation speed is switched.
Horn Fast/Slow Determines how long it takes for the rotation speed of the horn (higher range) to change from
Fast to Slow when the rotation speed is switched.
Rotor Slow Determines the frequency of the rotor (lower range) when the Speed Control is set to Slow.
Horn Slow Determines the frequency of the horn (higher range) when the Speed Control is set to Slow.
Rotor Fast Determines the frequency of the rotor (lower range) when the Speed Control is set to Fast.
Horn Fast Determines the frequency of the horn (higher range) when the Speed Control is set to Fast.
Rtr Slow/Fast Determines how long it takes for the rotation speed of the rotor (lower range) to change from
Slow to Fast when the rotation speed is switched.
Rtr Fast/Slow Determines how long it takes for the rotation speed of the rotor (lower range) to change from
Fast to Slow when the rotation speed is switched.
Effect Type Description Parameter Description
Uni Comp Down Compressor using
“downward”
algorithm for making
loud sounds quieter.
Threshold Determines the minimum input level at which the compressor effect is applied.
Knee Determines how the transition range changes around the threshold. The higher the value, the
shallower the transition curve.
Attack Determines the amount of time it takes for the effect to reach its maximum compression.
Release Determines the amount of time it takes for the compressor effect to diminish or fade out.
Ratio Determines the ratio of the compressor.
Side Chain EQ When this is turned on, the EQ is applied for the corresponding input level range of the Side
Chain.
SC EQ Q Determines the Side Chain EQ bandwidth.
SC EQ Freq Determines the center frequency of the Side Chain EQ.
SC EQ Gain Determines the level gain of the Side Chain EQ.
Dry/Wet Determines the balance of the dry sound and the effect sound.
Output Level Determines the output level of the effected sounds.
Make Up Gain Determines the output gain of the compressor block.
Post-comp HPF Determines the Cutoff Frequency of the High-Pass Filter which follows the compressor.
Clipper Determines the extent to which the Clipper is applied for forcibly reducing the gain.
Clipper Source Determines the signal to which the Clipper effect is applied for forcibly reducing the gain.
Side Chain Lvl Determines the Side chain input level.
Uni Comp Down
Ratio: 1.0
Ratio: 2.0
Ratio: 4.0
Threshold
Input
Output
MONTAGE Supplementary Manual
11
Effect Type Description Parameter Description
Uni Comp Up Compressor using
“upward” algorithm
for making quiet
sounds louder.
Threshold Determines the maximum input level at which the compressor effect is applied.
Knee Determines how the transition range changes around the threshold. The higher the value, the
shallower the transition curve.
Attack Determines the amount of time it takes for the effect to reach its maximum compression.
Release Determines the amount of time it takes for the compressor effect to diminish or fade out.
Ratio Determines the ratio of the compressor.
Side Chain EQ When this is turned on, the EQ is applied for the corresponding input level range of the Side
chain.
SC EQ Q Determines the Side chain EQ bandwidth.
SC EQ Freq Determines the center frequency of the Side chain EQ.
SC EQ Gain Determines the level gain of the Side chain EQ.
Dry/Wet Determines the balance of the dry sound and the effect sound.
Output Level Determines the output level of the effected sounds.
Make Up Gain Determines the output gain of the compressor block.
Post-comp HPF Determines the Cutoff Frequency of the High-Pass Filter which follows the compressor.
Clipper Determines the extent to which the Clipper is applied for forcibly reducing the gain.
Clipper Source Determines the signal to which the Clipper effect is applied for forcibly reducing the gain.
Gain Limit Determines the maximum gain level.
Side Chain Lvl Determines the Side chain input level.
Effect Type Description Parameter Description
Parallel Comp Compressor
applying parallel
processing of the
compressed sounds
and dry sounds.
Type Determines the compressor type.
Compression Determines the extent to which the compressor is applied.
Texture Determines the texture of the compressor effect.
Output Level Determines the output level of the effected sounds.
Input Level Determines the input level.
Effect Type Description Parameter Description
Presence Effect for bringing
out the hidden
presence in the
input sounds.
Presence Determines the extent to which the effect is applied.
Texture Determines the texture of the sound effect.
Output Level Determines the output level of the effected sounds.
Uni Comp Up
Ratio
Gain Limit
Threshold
Input
Output
MONTAGE Supplementary Manual
12
Additional New Performances
The MONTAGE offers 52 new Performances.
For the added Performances, refer to the Data List.
MONTAGE Supplementary Manual
13
Category Search
Performance Category Search, Arpeggio Category Search, Waveform Category Search
The Favorite function has been added, giving you quick access to the sounds and Arpeggios you want has been added. This
section explains an example of the Favorite function for Performance Category Search.
NOTE You can filter the Performance List by Favorite in the Part Category Search and in the Performance Merge, but you cannot turn the
Favorite icon on/off from the search displays.
Favorite Set / Unset
Enters (Sets) or cancels (Unsets) the Favorite icon to the currently selected Performance. This is not available when the cursor is
not on the Performance List.
NOTE You can also set/unset the Favorite icon from the menu which is displayed by touching the Performance name on the Performance Play
(Home) display.
Favorite All Clear
Clears all Favorite icons on Performances. This is available only when at least one Performance has a Favorite icon.
Bank/Favorite (Performance Bank Select/Favorite)
Filters the Performance List by Bank or Favorite. When Favorite is selected, only Performances having a Favorite icon are listed.
Settings: All, Favorite, Preset, User, Library Name (when the Library file is read)
NOTE When the Category Search display is selected, pressing the [CATEGORY] button repeatedly switches Banks among All, Favorite,
Preset, User, Library (when the Library file is read). Holding down the [CATEGORY] button lets you go back to All.
Operation
[PERFORMANCE] [CATEGORY] (Performance Category Search)
or
Touch the Performance Name Select [Search] from the displayed menu
Favorite icon
Favorite Set/Unset Favorite All Clear
Performance Bank Select/Favorite
MONTAGE Supplementary Manual
14
Part Category Search
When “Mixing” of the “Parameter with Part” (Param. with Part) setting is set to off, you can change sounds continuously, using
the current setting values for the Part such as Volume, Pan and Note shift.
Param. with part (Parameter with Part)
Determines whether or not to read and use the parameter values for the next Performance. When the set of parameters is set to
off, the current setting values are continuously used even when the next Performance is selected.
Settings: Off, On
Operation
[PERFORMANCE] (When the Part to which any sounds are assigned is selected) Select the Part Name
[SHIFT]+[CATEGORY] (Part Category Search)
or
(When the Part to which any sounds are assigned is selected) Touch the Part Name
Select [Search] from the displayed menu
Parameter with Part
MONTAGE Supplementary Manual
15
Performance Play (Home)
You can now see various information by turning “View” on.
View
Determines whether the detailed information of each Part is displayed (On) or not displayed (Off). The displayed information
differs depending on the cursor position or the Control function settings.
Settings: Off, On
NOTE When the cursor is on the Performance name on the Performance Play (Home) display, you can also switch the information views by
pressing the [PERFORMANCE] button.
This section explains when “View” is turned on.
Home
Operation
Press the [PERFORMANCE] button
or
Touch the [HOME] icon
View
MONTAGE Supplementary Manual
16
Element view
This appears only when the currently selected Part is the Normal Part (AWM2), and the [PERFORMANCE CONTROL] button or
“Element/Operator control” is turned on.
Element SW (Element switch)
Determines whether each Element is active or not.
Settings: Off, On
Element Level
Determines the output level of the Element.
Settings: 0 – 127
Drum Key view
This appears only when the currently selected Part is the Drum Part, and the [PERFORMANCE CONTROL] button or “Element/
Operator Control” is turned on.
Element SwitchElement Level
Drum Key Level
MONTAGE Supplementary Manual
17
Drum Key Level
Determines the output level of the Drum Key.
Settings: 0 – 127
Algorithm view
This appears only when the currently selected Part is the Normal Part (FM-X), and the [PERFORMANCE CONTROL] button or
“Element/Operator Control” is turned on.
Algorithm (Algorithm Number)
Changes Algorithms.
Settings: See the Data List PDF document.
NOTE Tapping the Algorithm image calls up the Algorithm Search display.
Feedback (Feedback Level)
Waveforms can be changed by feeding some of the signal generated by an operator back through that operator. This allows
you to set the feedback level.
Settings: 0 – 7
Operator Level
Determines the output level of the Operator.
Settings: 0 – 99
Algorithm
Number
Feedback
Level
Operator Level
MONTAGE Supplementary Manual
18
Part – Note view
This appears only when the [PART CONTROL] button is turned on or the cursor is on the Note Limit. This is useful for checking
the Layer/Split settings among Parts.
Velocity – Note view
This appears only when the cursor is on any velocity limit of Parts. This is useful for setting Velocity split among Parts.
Note Limit
Velocity Limit
MONTAGE Supplementary Manual
19
Motion Control
You can now make individual link setting of Assignable Knobs, to which functions commonly effective for all Parts are assigned,
with the Super Knob.
MS Master (Motion Sequencer Master Switch)
Turns the Motion Sequencer for the entire Performance on/off. This setting is applied to the [MOTION SEQ ON/OFF] button on
the panel.
Settings: Off, On
Super Knob MS (Super Knob Motion Sequencer Switch)
Turns the Motion Sequencer applied to the Super Knob on/off.
Settings: Off, On
Super Knob Link
Turns the link between the Assignable Knob and the Super Knob on/off. When this is set to off, the function value assigned to the
corresponding knob does not change even if the Super Knob is controlled.
Settings: Off, On
Motion Control
Super Knob
Operation
[PERFORMANCE] [Motion Control] [Super Knob]
Motion Sequencer Master Switch
Super Knob Motion Sequencer Switch
Super Knob Link
MONTAGE Supplementary Manual
20
Utility
You can now control the monitor volume of the Audio signal input from the [USB TO HOST] terminal.
USB Volume (USB Input Volume)
Adjusts the volume of the Audio signal input from the [USB TO HOST] terminal. This setting is applied to the output gain of the
OUTPUT (BALANCED) [L/MONO]/[R] jacks and the ASSIGNABLE OUTPUT (BALANCED) [L]/[R] jacks.
Settings: 0 – 127
NOTE USB Input Volume is stored as part of the general system settings, not as Performance data.
Settings
Audio I/O
Operation
[UTILITY] [Settings] [Audio I/O]
USB Input Volume
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/