2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. AmazonBasics
  6. N/A
N/A

AmazonBasics N/A, B07F2NC59L User manual

  • Hello! I am an AI chatbot trained to assist you with the AmazonBasics N/A User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
created by: Impala Services Ltd.
Page size: A4
B07F2C7GVT, B07F2NC59L, B07F2C7GVX
Classic Kitchen Faucet with Sprayer
Grifo de Cocina Clásico con Rociador
Robinet de Cuisine Classique avec Tête de Pulvérisation
English .............................3
Español ............................9
Français .........................15
3
Welcome Guide
•
English
Contents:
Before getting started, ensure the package contains the following components:
Faucet x1 Sprayer base x1
Rubber washer (faucet) x1 Rubber washer (sprayer base) x1
Metal washer (faucet) x1 Metal washer (sprayer base) x1
Mounting nut (faucet) x1 Mounting nut with/ screws (sprayer base) x1
Deck plate x1 Water diverter x1
Deck plate gasket x1 Sprayer with hose x1
Recommended Tools:
• Adjustable Wrench x1 • Cross-head Screwdriver x1
Part List
Parts Description Qty
A
Handle x1
B
Screw (M5 x 4 mm) x1
C
Red and blue indicator x1
D
Rubber O-ring x1
E
Flexible hose (hot/cold)
(M10 x 1-9/16-24UNEF-600)
x1
F
Diverter hose x1
G
Deck plate x1
H
Deck plate gasket x1
I
Rubber washer (Ø55 x Ø32 x 1.8 mm) x1
J
Metal c-shaped washer x1
K
Mounting nut x1
L
Diverter x1
M
Rubber washer x1
N
Rubber washer (Ø40 x Ø33 x 2 mm) x1
O
Rubber washer (Ø43.5 x Ø30 x 2 mm) x1
P
Metal washer x1
Q
Mounting nut with screws x1
R
Sprayer hose x1
S
Sprayer head x1
T
Threaded pipe (faucet) x1
U
Threaded pipe (sprayer base) x1
V
Sprayer base x1
A
B
C
D
E
G
H
V
I
J
K
L
M
N
O
P
Q
R
S
T
U
F
4
Before First Use
Check for transport damage.
Risk of suffocation! Keep any packaging materials away from children – these materials are a potential
source of danger, e.g. suffocation.
Installation
Step 1:
Shut Off Water Supply
• Locate water supply inlets and shut off the water supply
valves. These are usually found under the sink or near
the water meter. If you are replacing an existing faucet,
remove the old faucet from the sink and remove any dirt
and/or plumber’s putty from around the faucet holes.
Step 2:
Setup
Rubber
o-ring (D)
Rubber
o-ring (D)
One (1) Hole Sink
Three (3) Hole Sink
Base plate
gasket (H)
Base plate (G)
For 1-Hole Installation
• Remove mounting nut (K), metal washer (J) and
rubber washer (I) from threaded pipe (T).
Make sure the rubber o-ring (D) is at the
bottom of the faucet body before proceeding.
• Slide the hoses, pipes and threaded pipe through the
hole in the sink.
For 3-Hole Installation
• Remove mounting nut (K), metal washer (J) and
rubber washer (I) from threaded pipe (T).
Make sure the rubber o-ring (D) is at the
bottom of the faucet body before proceeding.
• Make sure the deck plate gasket (H) is inserted into the
deck plate (G).
• Position the deck plate (G) over the 3 holes in the sink.
• Slide the hoses, pipes and threaded pipe through the
deck plate (G), deck plate gasket (H) and the center hole
of the sink.
Step 3:
Mount in Place
Rubber washer (I)
Threaded pipe (T)
Metal c-shaped
washer (J)
Mounting nut (K)
• Slide the rubber washer (I), metal c-shaped washer (J),
over the water lines and onto the threaded pipe (T).
• Screw the mounting nut (K) onto the threaded pipe (T)
and hand-tighten.
Make sure the faucet or base plate (G) is
centered over the sink hole(s) and then finish tightening the
mounting nut (K) by hand.
DANGER
NOTICE
NOTICE
NOTICE
5
Installation
Step 4:
Connect Supply Lines
Hot water
inlet
Turn clockwise
Plumber’s
tape
Cold water
inlet
• Wrap the plumber’s tape in a clockwise direction around the hot and
cold water inlet threads.
• Screw the faucet supply line with the red marking onto the hot water
supply inlet and screw the blue faucet supply line onto the cold water
supply inlet.
• Tighten securely with a wrench.
Step 5:
Connect Diverter and Diverter Hose
Short
copper
pipe
Diverter
hose (F)
•
Screw the water diverter hose (F) to the short
copper pipe.
Swivel nut
Diverter
hose (F)
Diverter (L)
Diverter (L)
Male thread
• Screw the water diverter (L) into the swivel nut.
• Screw the water diverter hose (F) onto the male
threads of the water diverter.
The male end should be facing
to the left and the female opening to the right.
NOTICE
6
Installation
Step 6:
Install Sprayer Base
Sprayer base (V)
Threaded pipe (U)
Rubber washer (O)
Metal washer (P)
Mounting nut (Q)
• Remove mounting nut (Q), metal washer (P) and
rubber washer (O) from the threaded pipe (U).
• Insert sprayer base (V) into the hole.
• Slide the rubber washer (O) and metal washer (P) onto
the threaded pipe (U).
• Screw the mounting nut (Q) onto the threaded pipe (U)
and hand-tighten.
Make sure the sprayer base (V) is
centered over the sink hole and then finish tightening
mounting nut (Q) by hand.
• Use a cross-head screwdriver and tighten the 3 screws
on the mounting nut (Q).
Sprayer base (V)
Sprayer hose (R)
• Slide the sprayer hose (R) through the sprayer base (V).
Step 7:
Connect Sprayer Hose
Diverter (L)
Rubber
washer (M)
Sprayer
hose (R)
• Insert rubber washer (M) into diverter (L).
• Screw sprayer hose (R) into female end of the diverter (L)
and tighten with wrench.
WARNING
7
Installation
Step 8:
Check and Run Water
Handle (A)
Sprayer lever
Sprayer head (S)
Sprayer base (V)
Flexible
hose
(hot)
Water inlet valves
Flexible
hose
(cold)
• Check to make sure the faucet is tight.
• Slowly open one water inlet valve and check for leaks; if no leaks, open the valve all the way.
• Slowly open the other water inlet valve and check for leaks; if no leaks, open the valve all the way.
If a leak is spotted close the valve and remove water line and remove Teflon tape (if required) on threads
and re-tape the threads and connect the water line and repeat the process.
• Pull the handle (A) back and move it to the left and make sure you get hot water coming out of the faucet.
• Push the handle (A) all the way to the right and make sure you have cold water coming out the faucet
• Remove the sprayer head (S) from the sprayer base (V) and pull the hose out and make sure there is nothing obstructing
the hose from being pulled out and that the you can push the hose back in.
• With the water running, make certain the sprayer sprays when the lever is pushed in.
NOTICE
8
Cleaning and Maintenance
• Avoid using abrasive chemicals when cleaning, read the cleaner product label prior to use.
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these
instructions must be included.
When using the product, basic safety precautions should always be followed to reduce the risk of injury including the
following:
• To reduce the risk of injury or property damage, read all instructions before installing product.
• Wear safety goggles.
• Product must be installed in accordance with all state & local plumbing & building codes.
• Call a professional if you are uncertain about installing this product.
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ
CAREFULLY.
Warranty Information
To obtain a copy of the warranty for this product:
Visit amazon.com/AmazonBasics/Warranty
— or —
Contact Customer Service at 1-866-216-1072
Feedback
Love it? Hate it?
Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you
to write a review sharing your experiences with the product.
Please visit: amazon.com/review/review-your-purchases#
For further services:
Visit amazon.com/gp/help/customer/contact-us
— or —
Contact Customer Service at 1-866-216-1072
MADE IN CHINA
amazon.com/AmazonBasics
/