SINKOLOGY BRV-1405BC-F040 Installation guide

Installation Guide

Install your new sink with step-by-step instructions.

Installation Guide

Bath Sinks

Drop-In

Undermount

Dual Flex

Vessel

Drains

Bathtubs

Freestanding

 OverowandWasteKit

 Rough-InKit

Kitchen + Bar Sinks

Drop-In

Undermount

Farmhouse

Drains

Fireclay

Bath Sinks

Bath Sinks: Drop-In

Drop-In sinks are designed to be easy to install in a wide range of

countertop materials. Sinkology copper sinks make updating your

bathroom design effortless.

1. Flip sink upside down and trace outside edge onto craft paper

orcardboard.Addasecondline1/2”inchinsidetherstline.

Cut out the center of the template using the second line.

2. Place the template on the countertop and trace the template.

Cut the installation hole in the countertop.

3. Position the sink in the hole and check for gaps around the rim.

Eliminate gaps by gently tapping the rim with a rubber mallet.

4. Weighthesinkdownandapplypolyurethaneexpandingfoam

underneath the sink to seal the gap between the sink and the

countertop to secure the sink

in place.

5. Use plumbers putty on the

underside of the drain lip to

seal the drain to the sink. See

diagram.

6. Apply Sinkology antique

brown or clear neutral cure 100% silicone around the rim of

the sink to form a water tight seal. See our Complete Silicone

InstallationKit(#SINSTALL-101) for Copper Sinks.

7. For regular maintenance simply wash with gentle soap

and water. For extra protection against water spotting, use

Sinkology Copper Armor care kit (#SARMOR-101) or high quality

carnauba wax.

8. Register your new sink at sinkology.com/registration.

Important

Sinkology bathroom drop-in sinks do not use mounting hardware. Our

preferred mounting method requires expanding foam and 100% silicone

to secure your copper sink into place.

PRO

DIY

Bath Sinks: Undermount

Undermount sinks are the ideal choice for a clean high-end look

with granite or solid surface countertops. This installation maximizes

countertop space and highlights the elegance of your countertop.

1. Flip sink upside down on

a sheet of craft paper or

cardboard and trace the

outside rim of the sink. Select

preferred countertop offset.

See diagram. Measure the

distance between the edge of

the basin and the inside edge

of the lip. Add a second line

insidetherstaccordingto

this measurement. Cut out the template along the second line.

2. Place the template onto the countertop and cut the hole into

the countertop.

3. Use clear or Sinkology antique

brown neutral cure 100%

silicone (#SINSTALL-101) on

the rim of the sink. Mount

sink under the countertop

using approved countertop

mounting hardware. See

diagram. Sinkology does

not provide under mounting

hardware due to the wide

varietyofmountingsurfaceswhichrequirespecichardware.

Contactyourcountertopmanufacturerforspecicmounting

hardware.

4. Slide the drain through

the drain hole in the basin.

Use plumbers putty on the

underside of the drain lip to

seal the drain assembly to the

sink and clean off and excess

See diagram.

Important

Sinkologyundermountsinksdonotincludemountinghardware.We

recommend providing your sink details to your countertop manufacturer

for approved mounting hardware and method.

PRO

DIY

Bath Sinks: Undermount (continued) Bath Sinks: Dual Flex

5. To complete your install we recommend applying a thin bead of

Sinkology antique brown or clear neutral cure 100% silicone to

any gaps between sink and countertop.

6. For regular maintenance simple wash with gentle soap and

water. For extra protection against water spotting, use Sinkology

Copper Armor care kit (#SARMOR-101) or high quality carnauba

wax.

7. Register your new sink at sinkology.com/registration.

Copper sinks featuring our exclusive Dual Flex rim are approved

for undermount or drop-in applications. The Dual Flex rim features

aatundermountrimwithslightbendallowingforfunctionaland

beautiful drop-in or undermount installation.

Please reference your preferred installation methods instructions:

Bath Sinks: Drop-In Page 4

Bath Sinks: Undermount Page 6

Important

DualFlexcoppersinkscanbeidentiedbytheirunique

rimdesign.ADualFlexrimwillhaveaatundermounting

surface and a decorative curved edge.

Bath Sinks: Vessel

3. Apply Sinkology antique brown or clear neutral cure 100%

silicone (#SINSTALL-101) to the edge of the hole and mount sink

into place. Apply plumbers putty on the underside of the drain

lip and assemble the drain.

4. Place the large steel mounting

washer over the drain pipe

and tighten the brass locknut

untilthesteelwasherisrmly

attached to the underside

of the countertop, holding

the entire sink in place. See

diagram.

5. For a professional look add

a bead of Sinkology antique brown or clear neutral cure 100%

silicone around the base of the sink.

6. For regular maintenance simple wash with gentle soap and

water. For extra protection against water spotting, use Sinkology

Copper Armor care kit (#SARMOR-101) or high quality carnauba

wax.

7. Register your new sink at sinkology.com/registration.

Vessel sinks are an easy way to add character and style to any

bathroom. Vessel sinks install directly on top of your countertop

and are reminiscent of old wash basins. This unique and luxurious

sink style is easy to install and are available in a wide variety of styles

andnishes.

1. Flip sink upside down and trace outside edge onto craft paper

or cardboard. Mock up any plumbing connections and faucet

placement to ensure necessary clearances. Cut out template

and place on the countertop.

Mark the center location of

the sink on the countertop.

2. Drill a 2 ¾” inch diameter

hole in your countertop

at the center mark. A

1/8th inch beveled edge

is recommended, but not

necessary. See diagram.

Important

Sinkology copper vessel sinks are designed to be installed securely in

a 2-3/4” inch hole in the countertop. Sinkology does NOT recommend

vessel mounting rings.

PRO

DIY

Bath Sink: Drains

Sinkology bathroom sink drains are constructed of solid bass and

handnishedtocomplementSinkologybathroomsinks.Sinkology

grid and pop-up bath sink drains work with most standard No-

OverowsinksandareprotectedbyaLifetimeWarranty.

1. Washanddrythesinkandthe

drain.

2. Remove lock nut, rubber

washer and white plastic

washer from drain stem.

3. Apply plumbers putty on the

underside of the drain lip

and slide the drain into sink

drain hole. The drain and the metal of the sink will be touching

with a thin layer of plumbers putty creating a water tight seal

aroundthedrain.Wipeoffexcessplumbersputty,itcouldstain

your copper sink.

4. If you do not have a vessel sink, skip to Step 5. If you have a

Sinkology copper vessel sink you should have received a large

steel washer with your sink. This washer slides up the drain

piperst.

5. Slide the rubber washer onto the drain stem until up against

bottom of sink or vessel washer. Slide on white washer then

lock nut onto threads until drain is tight and secure.

6. Test all connections for leaks.

Important

Sinkologybathdrainsfeatureano-overowdesignandshouldonlybe

installedintobathroomsinkswithoutoverowholes.Ifyoursinkhasan

overow,youwillneedtopurchaseanoverowsinkdrain,availableat

most retailers. See diagram.

PRO

DIY

Bathtubs

Bathtubs: Freestanding

Every Sinkology copper bathtub is skillfully hand-hammered

andcarefullynishedbyourteamofcoppersmiths.Each

bathtub is hand-tested multiple times to ensure no leaks and

perfect performance.

1. Gather the products being installed and the tools you will need.

It’s easier to install your drain and faucet before placing the tub.

2. Installthedrainandoverowdrainsontothebathtubperthe

drainandoverowkitinstructions.

3. Install the faucet per the manufacturer’s instructions.

4. Place bathtub in desired location and mark exact location on the

oor.

5. Runthedrainpipesthroughtheoorandattachtothe

plumbing. This step is best handled by a professional.

6. Onceplacementisnal,apply Sinkology antique brown or

clear neutral cure 100% silicone (#SINSTALL-101) caulk around

the tub. Allow the caulk to set for 24-hours (or timing per the

manufacturer’s instructions) before using your copper tub.

7. Register your new bathtub at sinkology.com/registration.

Important

Sinkology copper bathtubs are handmade so variations in dimensions can

occur.Werecommendperformingrough-Inprocedureswiththebathtub

on site to ensure the correct installation.

PRO

DIY

Bathtubs:Drain+OverowKit

Bathtubdrainandoverowkitsfeatureadurableandbeautiful

custombronzenishdesignedtolookandworkbeautifullywith

Sinkology freestanding copper bathtubs.

1. Loosely assemble selected freestanding bathtub waste drain or

overowkitontobathtub(leavingoffthetailpipesatthistime).

2. Determinewaterlinelocationsforselectedbathtubller.Tub

faucet may need to be assembled prior to tub installation.

3. Placebathtubinnallocationandmarkexactlocationonthe

oor.

4. Rough-Innalplumbingwastedrainandwaterlinesintoproper

locations.WerecommendusingOS&B(#ITD35) rough-in kit. This

kit is designed to work with most freestanding bathtubs and

makes plumbing rough-in

fast and easy, and ensures a

watertight connection. See

diagram.

5. Register your new bathtub at

sinkology.com/registration.

Important

Sinkology copper bathtubs are handmade so variations in dimensions can

occur.Werecommendperformingrough-Inprocedureswiththebathtub

on site to ensure the correct installation.

PRO

DIY

Bathtubs:Rough-InWasteDrain

The copper bathtub rough-in kit not only makes installation easier,

butitsavestimeandmoney.Designedtoworkspecicallywith

Sinkology copper bathtubs, and is protected by a lifetime warranty.

1. Final waste drain and waterline rough-in’s should be completed

andooringshouldbenished.Ensurebathtubisproperly

supported and level.

2. Double check bathtub faucet installation requirements before

nalbathtubinstallation.

3. Apply thread sealant or plumbers tape to any threaded

connections that do not have rubber gaskets.

4. Applyplumbersputtytoundersideofdrainangeandthread

through the bathtub and into drain pipe.

5. Ensurewastedrainandoverowissecurelyconnectedto

bathtub.

6. Place tub back into desired location and verify that bathtub is

level. If using recommended rough-in kit (#ITD35), the tub will

needtobeliftedapproximately8”beforeloweringintonal

position.

7. Finish installation by running a bead of silicone adhesive

around the base of copper freestanding bathtub where

applicable to create a watertight seal.

8. Allow sealants and adhesive to thoroughly dry before

llingbathtubwithwater.Consultsealantandadhesive

manufacturers for dry times, as they may vary.

9. Register your new bathtub at sinkology.com/registration.

Important

Sinkology copper bathtubs are handmade so variations in dimensions can

occur.WerecommendperformingRough-Inprocedureswiththebathtub

on site to ensure the correct installation.

PRO

DIY

Kitchen & Bar Sinks

Kitchen&BarSinks:Drop-In

Drop-in kitchen sinks are easy to install and are designed to install

beautifully in a wide range of countertop surfaces. Sinkology Drop-In

kitchen sinks make DIY kitchen renovations effortless and impactful.

Drop-In sinks can be used to replace an old sink or installed in

luxurious new countertops.

1. Flip sink upside down and trace the outside edge onto craft

paper or cardboard. Add a second line that is 1/2” inside that

line. Cut out the traced template using the second line.

2. Positionthetemplateatonthecountertopandalignwith

cabinet and plumbing connections.

3. Mark openings and cut the countertop.

4. Alwaysdoublecheckthesinkfortinsidetheholebefore

moving on.

5. If your sink does not come with mounting hardware, refer to

bath sink drop-in installation instructions on page 4.

6. Before dropping your new sink into the countertop for the last

time apply a thick bead of Sinkology antique brown or clear

neutral cure 100% silicone around the hole on the countertop

to form a water tight seal around the sink. See our Complete

SiliconeInstallationKit(#SINSTALL-101) for Copper Sinks.

7. Install hardware. Place

notched end of all bolts

into the keyhole slots. See

diagram. Lower the sink

carefully into the countertop

so the bolts enter without

interference.

Important

Not all Drop-In kitchen sinks require mounting hardware. If your

kitchen sink does not come with mounting brackets, we recommend

securing your sink with 100% silicone and expandable foam

(see bath sink drop-in instructions on page 4)

PRO

DIY

8. Turn the claws out 90

degrees so they will grasp the

underside of the countertop.

See diagram.

9. Claws can be bent to

accommodate larger or

smaller gaps. Tighten the

clamps evenly until all of the

clamps grasp the underside of

thecountertoprmlyandsecurely.

10. Some Sinkology copper sinks

feature rear deck brackets that

are designed for hardware

with two claws per bolt. First

claw closest to bracket bolt tip

will sit against the underneath

of the sink rim. Second

claw will be used to grab

underneath the countertop.

See diagram.

11. Install drains.

12. For a professional look apply a thin bead of Sinkology antique

brown or clear neutral cure 100% silicone around the rim.

13. For regular maintenance simply wash with gentle soap and

water. For extra protection against water spotting, use

Sinkology Copper Armor care kit (#SARMOR-201) or high quality

carnauba wax.

14. Register your new sink at sinkology.com/registration.

Kitchen&BarSinks:Drop-In(continued)

Kitchen&BarSinks:Undermount

Undermount kitchen sinks are recommended when installing new

granite or solid surface countertops. Undermount installation adds

a luxurious and professional look to kitchen design and maximizes

countertop space. By installing your Sinkology kitchen sink under-

counter it makes wiping countertops easy and helps during kitchen

clean up.

1. Flip sink upside down on

a sheet of craft paper or

cardboard and trace the

outside rim of the sink. Select

preferred countertop offset.

See diagram. Measure the

distance between the edge of

the basin and the inside edge

of the lip. Add a second line

insidetherstaccordingto

this measurement. Cut out the template along the second line.

2. Place the template onto the countertop and cut the hole into

the countertop.

3. Use clear or Sinkology antique brown neutral cure 100% silicone

(#SINSTALL-101) on the rim of the sink. Mount sink under the

countertop using mounting hardware. Sinkology does not

provide under mounting hardware due to the wide variety of

mountingsurfaceswhichrequirespecichardware.Contactyour

countertopmanufacturerforspecicmountinghardware.

4. Ensuresinkismountedatagainstcountertoponallsides,

adjust hardware as needed.

5. Use plumbers putty to install the drain. Clean excess.

6. To complete your install we recommend applying a thin bead of

Sinkology antique brown or clear neutral cure 100% silicone to

any gaps between sink and countertop.

7. For regular maintenance simple wash with gentle soap and

water. For extra protection against water spotting, use Sinkology

Copper Armor care kit (#SARMOR-101) or high quality carnauba

wax.

8. Register your new sink at sinkology.com/registration.

Important

Sinkology undermount kitchen sinks do not include mounting hardware.

Werecommendprovidingyoursinkdetailstoyourcountertop

manufacturer for approved mounting hardware and method.

PRO

DIY

KitchenFarmhouseSinks:Undermount

Farmhouse kitchen sinks are the ultimate kitchen design element.

Sinkology apron front kitchen sinks are design to be highly function

yet make a bold statement. The apron front design and large

spacious bowl make kitchen clean up more comfortable.

Farmhouse sinks require extra installation steps, we recommend

using professional tools and professional experience when installing

farmhouse copper sinks. Occasionally the cabinet face front

and countertop will be cut to accommodate apron front sinks.

Undermount farmhouse sinks require additional support to hold sink

in place.

1. Flip sink upside down on a piece of craft paper or cardboard

and trace the edge of the basin. Measure the distance between

the edge of the basin and the inside edge of the lip. Add a

secondlineinsidetherstaccordingtothismeasurement.Cut

on the second line to make your cut out template. The apron

Important

Most Sinkology farmhouse kitchen sinks can be installed as an

undermountordrop-in.Werecommendundermountinstallationwith

new granite or solid surface countertops.

front is designed to extend past the front of the cabinet. Take

thismeasurementbeforemakinganycuts.Whenyoumakeyour

cut out measurements, accommodate the apron extending past

the cabinet front.

2. Cut the countertop and cabinet front to accommodate the sink

basin using your cut out template.

3. Build a support ledge for your sink. Screw three lengths of 2x4’s

(depends on cabinet width) along the back and both sides of

cabinet. Sink is fully supported when ¾” inch of rim is supported

on three sides. If additional support is needed four vertical 2x4

supports can be installed. See diagram.

PRO

DIY

KitchenFarmhouseSinks:Undermount(continued)

4. Ensure top sink rim rests 1/8” below top of cabinet frame when

supported and in place.

5. Countertops will be placed directly on top of cabinet and sink.

Farmhouse sink typically needs to be fully in place before

countertop templating can begin.

6. Install the countertop. Apply thin bead of Sinkology antique

brown or clear neutral cure 100% silicone into any gaps between

sinkandcountertop.SeeourCompleteSiliconeInstallationKit

(#SINSTALL-101) for Copper Sinks.

7. For regular maintenance simple wash with gentle soap and

water. For extra protection against water spotting, use Sinkology

Copper Armor care kit (#SARMOR-201) or high quality carnauba

wax.

8. Register your new sink at sinkology.com/registration.

KitchenFarmhouseSinks:Drop-In

4. Sinkology farmhouse sinks are

considered fully support when

¾” inch or more of the rim is

supported on three sides.

5. Apply a thick bead of

Sinkology clear or antique

brown neutral cure 100%

silicone around the edge of

the countertop and install

sink.Wipeoffexcesssilicone.SeeourCompleteSilicone

InstallationKit(#SINSTALL-101) for Copper Sinks. See diagram.

6. Allow silicone 24-48 hours to cure before using sink.

7. For a professional look apply a thin bead of Sinkology antique

brown or clean neutral cure 100% silicone around the edge of

your sink and countertop.

8. For regular maintenance simply wash with gentle soap

and water. For extra protection against water spotting, use

Sinkology Copper Armor care kit (#SARMOR-201) or high quality

carnauba wax.

9. Register your new sink at sinkology.com/registration.

1. Flip sink upside down on a piece of craft paper or cardboard

and trace the edge of the basin. Add a second line approx.

3/4” inch inside that line. Cut out the traced template using

the second line. Note: The apron front is designed to extend

past the front of the cabinet. Take this measurement before

makinganycuts.Whenyoumakeyourcutoutmeasurements,

accommodate the apron extending past the cabinet front.

2. Cut the countertop and cabinet front to accommodate the sink

basin using your cut out template.

3. Oftencabinetdoorsneedtobemodiedtoallowforextra-

large Sinkology farmhouse copper sinks.

PRO

DIY

Farmhouse apron front kitchen sinks are a great centerpiece to any

kitchen. Our farmhouse sinks can be dropped in to existing countertop

and cabinets with a simple DIY project to make your kitchen the envy of

friends and family.

Important

Most Sinkology farmhouse kitchen sinks can be installed as an

undermount or drop-in. If your sink has 1/2” inch rim or less, it was

designed for undermount installation only.

Kitchen&BarSinks:Drains

Sinkology drains are designed to perfectly complement Sinkology copper

sinks.Sinkologykitchendrainsaredesignedtotanystandarddrainhole.

SinkologydisposalangesaredesignedforInSinkEratordisposals.

Basket Strainer

1. Unscrewthelockingnutandwasherfromthedrainange.

2. Apply plumbers putty

around the underside of

theouterdrainangelip

and place it in the drain

hole in the sink. The metal

angewillsitdirectlyonthe

metal sink. Clean any excess.

See diagram.

3. Place the rubber washer on the large, metal nut and screw the nut

on to the drain underneath the sink.

4. Wipeawayanyexcessplumbersputtyaroundtherimofthedrain.

Disposal Flange

1. OurdisposalangeisdesignedtoonlyworkwithInSinkErator

disposals. Follow the InSinkErator instructions to install the

disposaltotheange.

2. Apply plumbers putty around

the underside of the outer

drainangelipandplaceitin

the drain hole in the sink. The

metalangewillsitdirectlyon

the metal sink. See diagram.

3. Wipeawayexcessplumbersputtyaroundtherimofthedrain.

Important

SinkologydisposalangesaredesignedforuseonlywithInSinkErator

disposals. If you have questions regarding drains, please contact

customerservice@sinkology.com for assistance.

PRO

DIY

Page is loading ...

SINKOLOGY BRV-1405BC-F040 Installation guide

Related papers

Other documents