Intellian i4P User manual

i3/i3L/i4/i4P

Installation and operation

User Manual

Document Number: 2012EF-UM1004-V1_0

2

Intellian Satellite TV Antenna Systems

Intellian i3/i3L/i4/i4P Serial Number

This serial number will be requested for all troubleshooting or service Inquiries.

Notice

Intellian i3/i3L/i4/i4P® and Intellian® are the registered trademarks of Intellian Technologies, Inc., and should not be appropriated without permission by Intellian Technologies,

Inc., and the information contained in this manual is the property of Intellian Technologies, Inc. Any and all parts of this manual shall not be reproduced and distributed in any form

without written prior consent by Intellian Technologies, Inc. The information contained in this manual shall be subject to change at any time without notice due to the functional

upgrade of the product.

3

INTRODUCTION

INTRODUCTION TO INTELLIAN i3/i3L/i4/i4P

FEATURES OF INTELLIAN i3/i3L/i4/i4P

BASIC SYSTEM CONFIGURATION OF INTELLIAN i3/i3L/i4/i4P

INSTALLATION

SYSTEM COMPONENTS

TOOLS REQUIRED FOR INSTALLATION

PLANNING THE INSTALLATION

INSTALLATION AND MOUNTING OF ANTENNA

INSTALLING THE ACU

ACU DIMENSIONS

SELECTING ACU INSTALLATION SITE

CONNECTING THE SYSTEM CABLES

CONNECTING THE SYSTEM TO A GPS

ADJUSTING THE LNB SKEW ANGLE (LINEAR POLARIZATION ONLY)

OPERATION INSTRUCTION

INTRODUCTION

OPERATING THE ACU

ACU SOFT KEYS

NORMAL MODE

SETUP MODE

OPERATION USING PC CONTROLLER PROGRAM

INTRODUCTION

PROGRAM INITIALING AND SERIAL PORT SETUP

MAIN MENU

CONTROLLER MENUS

PREPARATION FOR TRANSPORTATION

WARRANTY

APPENDIX : TECHNICAL SPECIFICATION

INTELLIAN i3/i3L

INTELLIAN i4/i4P

4

5

6

7

10

11

13

18

19

20

23

24

26

27

30

50

51

52

54

62

63

64

65

Table of Contents

4

Intellian Satellite TV Antenna Systems

Introduction to Intellian i3/i3L/i4/i4P

Intellian i3/i3L/i4/i4P is a digital satellite antenna system designed specically

for all types of vessels (anchored or transit) to automatically identify, track

and capture satellite signals from the Digital Video Broadcasting (DVB: the

international standard for digital TV transmissions) compatible satellites.

In details, Intellian i3/i3L/i4/i4P has Wide Range Search (WRS) algorithm, which

minimizes the search time during initialization, and Dynamic Beam Tilting (DBT)

technology, which dynamically shapes the antenna beam to utilize stabilization.

While tracking the target satellite, DBT technology uses a high-performance,

constantly adjusting sub-reector which allows the antenna to remain relatively

still, eliminating the constant whine of stepper motors while staying locked on to

the satellites.

The i3/i3L/i4/i4P has a builtin GPS system which enhances the speed of satellite

signals acquisitions. In addition, the i4P provides the embedded auto skew angle

control system to maintain the optimal signal strength and increase the quality of

satellite receptions in weak satellite single coverage area.

Introduction

5

Introduction

Features of Intellian i3/i3L/i4/i4P

Enjoy satellite broadcasts at sea

Intellian i3/i3L/i4/i4P is the most modern antenna system that enables

you to receive a high quality broadcasting signal at sea, where the

atmospheric and environmental condition are very harsh. This fully

automatic control system allows you to simply turn the power switch

on, and have crystal clear, high quality satellite television in motion or at

anchor.

High quality antenna

High tech parabolic antenna technology has been adopted for this

antenna system, which is optimal for marine conditions. This enables

you to receive the optimal signal level even when it is raining or

snowing.

Fast and efcient search for the satellite

The WRS (Wide Range Search) algorithm allows for the antenna

system to search the satellite within the shortest amount of time and

to detect the satellite signal under any position and with any directional

movement of the vessel.

Easy installation and outstanding reliability

Intellian i3/i3L/i4/i4P uses only one RF cable for installation. This makes

installation easy. Power, RF and data signals transfer from the antenna

to the ACU through this single cable. In addition, Intellian i3/i3L/i4/

i4P provides highly reliable system through the implementation of a

modularized design, and the usage of strictly proven components.

Built-in GPS

The built-in GPS system enhances the speed of acquisition of the

satellite signal and provides Intellian i3/i3L/i4/i4P even higher

performance.

Built-in automatic skew angle control system (i4P Only)

The automatic skew control system allows Intellian i4P to maintain the

optimal skew angle at all times and ensure maximum level of satellite

signal level receptions.

Intellian’s environmental test standards certied

These standards are much severer than a typical experienced marine

equipment condition. All testes performed with one unit through all

continued sequences. Intellian standards meet LR and DNV standards as

well as EN60945.

6

Intellian Satellite TV Antenna Systems

Basic System Conguration of Intellian

For your satellite TV system to function properly, the system will have to

be connected with all of the provided components as shown on the right

(Refer to the next chapter ‘Installation’ in this manual for more detailed

connection instructions). Separate purchase of a satellite receiver and a

TV is required.

Note: i3L can only be connected to one receiver.

Note 2: Dish and Bell TV users please refer to the Intellian Dish MIM

Installation and User Manual.

Figure 01 : Basic Conguration with 2 Receivers

ANT RF1

FUSE

FG - +

+ -

TV

(Not Supplied)

Antenna Control Unit

DC Power on Vessel

( 9~30 V DC )

NMEA GPS

PC( Not Supplied)

Satellite Receiver #2

(Not Supplied)

RF1

RF2

NMEA

RECEIVER

DC 9~30V PC INTERFACE

TV

(Not Supplied)

Satellite Receiver #1

(Not Supplied)

7

The components of the Intellian i3/i3L/i4/i4P are designed as module

system so that it is suitable for simple installation on all types of

vessels.

System Components

Antenna Unit

The antenna of Intellian i3/i3L/i4/i4P is comprised of the following

components for optimum search and receiving satellite signal.

• Mechanical Unit – manipulates the antenna to receive the optimal

satellite signal regardless of the movement of the vessel.

• Control Unit – controls mechanical operation of the antenna.

• RF Unit – transmits the optimum satellite signal to the receiver.

• Radome – protects the antenna from the severe marine environment.

Installation

Figure 02 : Radome

8

Intellian Satellite TV Antenna Systems

Antenna Control Unit (ACU)

The Antenna Control Unit (ACU) provides the power to the antenna and

controls the various settings of the antenna. The digital VFD (Vacuum

Fluorescent Display) allows for easy operation of the ACU, even in the

dark.

The functions of the ACU are as follows:

• Controls the antenna system

• Provides power to the antenna unit

• Monitors the antenna status

• Changes the target satellite

• Set up the user environment

• Set the current GPS information

• Set satellite information

• Move antenna manually

• Perform self-diagnosis of the antenna

• Set up the interface with a PC

Figure 03 : Front & Rear of ACU

NMEA

ANT RF1 RECEIVER

FUSEDC 9~30V PC INTERFACE

FG - +

+ -

Front

Rear

Antenna Control Unit

9

Installation Kit

Contains the items required for securing the antenna unit and ACU to the

vessel.

Other Components

No Components Size Qty

1 ACU Table Mounting Bracket - 2EA

2 RF Cable (ACU to IRD) 49ft (15m) 1EA

3 RF Cable (ACU to IRD) 10ft (3m) 1EA

4 DC Power Cable 33ft (10m) 1EA

5 PC Serial Cable 6ft (1.8m) 1EA

6 NMEA Connector AK950-2 1EA

7 Power Connector AK950-3 1EA

8 Hex Bolt M8x35L 5EA

9 Tapping Screw ø4x16L 5EA

ø3x8L 5EA

10 Flat Washer M8 5EA

11 Spring Washer M8 5EA

12 Installation CD - 1EA

13 User Manual - 1EA

14 Mounting Template i3/i3L 1EA

i4/ i4P

15 Quick Installation Guide - 1EA

Figure 05 : List of the Supplied Parts

Figure 04 : Installation Bolt Kit

Hex.Bolt

5

Hex. Nut

5

Spring Washer

5

Flat Washer

5

Antenna

Item

Qty

ACU

Item

Qty

Size

Self-Tapping Screw

5

(M4 X 16L)

Machine Screw

5

(M3 X 8L)

10

Intellian Satellite TV Antenna Systems

Tools Required for Installation

Power Drill 11 mm Spanner

Cross-Head

Screwdriver 13 mm Spanner

10 mm Drill Bit

Ø80 mm

Hole Saw

Pencil

5 mm

Allen/Hex key

Power Drill 11 mm Spanner

Cross-Head

Screwdriver 13 mm Spanner

10 mm Drill Bit

Ø80 mm

Hole Saw

Pencil

5 mm

Allen/Hex key

Figure 06 : Required Tools for Installation

11

Planning the Installation

Antenna Unit

Install the antenna in accordance with the following procedures to

ensure maximum performance of the antenna. The antenna should

be installed in a place where it has an all-around clear view of the

horizon. Please be sure there are no obstacles within 15 degrees above

the antenna. Any obstacles can prevent the antenna from tracking the

satellite signal (Refer to the drawing on the right).

Do not install the antenna near by the radar especially on the same

plane as their energy levels may overload the antenna front-end circuits.

It is recommended to position the antenna at least 4 feet (1.2m) above

or below the level of the radar and minimum of 15 feet (6m) away from

the high power short wave radars.

The mounting platform should be rigid enough and not subjected to

excessive vibration. The movement of the antenna can be minimized

by installing at the center of the vessel. For optimal performance of the

antenna, it is not recommended to install at any corner of the vessel,

where the movement of the vessel is the greatest. Install the bottom

of the antenna parallel to the surface of the sea and x tightly to the

structure of the vessel. When setting the antenna down, be careful not

to damage the RF connector. Striking the connectors on the bottom

directly will damage the connector.

Figure 07 : Elevation Limit of Obstacles

15°

12

Intellian Satellite TV Antenna Systems

Cables

Before installing the system cables, consider the following points.

• All cables need to be well clamped and protected from physical

damage

and exposure to heat and humidity.

• Cables with severe bends are not allowed.

• Where a cable passes through an exposed bulkhead or deckhead,

a watertight grommet or swan neck tube should be used.

Power Requirements

Follow the power requirements to avoid damage to the system.

The Intellian i3/i3L/i4/i4P has been designed to work on a boat’s power

supply rated from 9 ~ 30 V DC.

If your IRD(s) and television(s) require a 110V/240V AC power supply,

you will need to install a suitable DC to AC converter to operate the

unit(s) from your boat’s DC power supply.

RF Cable

This cable is supplied at a length of 49ft (15m). If a longer length is

required you should replace this cable with an extended RF cable

supplied by Intellian Technologies.

Extending the Cables

The cables that have been supplied with your Intellian system should be

of adequate length to complete the installation on most vessels.

Note: Exceeding the indicated cable lengths will result in reduced

performance of your system.

13

Installation and Mounting of Antenna

The method of installation and mounting of antenna may vary due

to vessel design but the following procedures are applicable in most

situations, and will result in a secure and effective installation.

Conrmation of Size Prior to Installation

• Check the height and diameter of the bottom surface of the antenna

before installing.

• The space must be sufcient for installing the antenna unit

considering the height and diameter of the antenna.

• The height and the diameter of the bottom surface of the antenna are

as shown

in the following drawing. If possible, install the antenna using a power

tower.

Note: Before installing the antenna, open the radome and remove the

shipping constraints from the antenna interior. Reinstall the radome

before operating the system. The system will not perform properly if the

radome is open.

Figure 08 : Radome Dimension of i4 / i4P

Ø43 cm (16.9”)

44 cm (17.3”)

Ø50 cm (19.7”)

54 cm (21.2”)

14

Intellian Satellite TV Antenna Systems

Figure 09 : Radome Dimension of i3 / i3L

Ø43 cm (16.9”)

44 cm (17.3”)

Ø50 cm (19.7”)

54 cm (21.2”)

15

Mark of the Antenna Mounting Position

Referring to the mounting template, mark where antenna will be

mounted on board (it must be a at surface) or on a separate power

tower.

Note: If a power tower is not suitable to mount the antenna, separate

cable shock and waterproong measures must be taken to protect the

RF connector from being exposed to the sea water and external shocks.

An exposed cable may cause electric shock and cause serious damage

to the equipment.

16

Intellian Satellite TV Antenna Systems

Figure 11 : Mounting Hole Position of i3 / i3LFigure 10 : Mounting Hole Position of i4 / i4P

22.86 cm (9”)

23.3cm ( 9.2”)

14.15cm (5.6”)

17

Securing Holes for Bolts and Cable Ways

Make 4 bolt holes of 10mm diameter, one at each corner of a rectangle

drawn as below, and make a circular hole of 80mm diameter at the

center of the rectangle through which the cable will run.

Connection of the Cable

Remove the rubber cap from RF connector. Connect the RF cable to the

RF connector under the base plate through the access hole using an

11mm spanner. Be careful not to over tighten, as you may damage the

connector.

Figure 13 : Connectors on Bottom of Antenna

Note: Do not tighten excessively when using the spanner, this will

damage the threads. Be careful that the connectors do not touch the

mounting surface of the antenna, this might cause a critical malfunction

and serious damage to the equipment.

Ø80mm

Hole Saw

Ø 10mm

Drill

Figure 12 : Drilling Instruction

Antenna Unit

RF1 Cable

Optional

11mm

Spanner

18

Intellian Satellite TV Antenna Systems

Mounting the Antenna

Attach the antenna by using the hex head bolts (M8X35L), M8 spring

washers, and M8 at washers supplied.

Figure 14 : Mounting the Antenna

Radome Base

Deck

M8 Flat Washer

M8 Spring Washer

M8 Hex. Bolt

13mm Spanner

ACU Dimensions

Installing the ACU

5.4 cm (2.1”)

5.5 cm (2.2”)

22.8 cm (9”)

17.8 cm (7”)

21.7 cm (8.5”)

18.5 cm (7.3”)

Figure 15 : Dimension of ACU

19

Figure 16 : Installation of ACU

Selecting ACU Installation Site

The ACU should be installed below deck, in a location that is:

• Dry, cool, and ventilated.

• Easy access from your main TV viewing area.

To Install the ACU

1. The ACU should be installed using the two supplied mounting

brackets which allow for a top or bottom mounting conguration.

2. Using the self tapping screws supplied, attach the mounting brackets

to the sides of the ACU.

3. Place the ACU in the location where it is going to be installed.

4. Connect the cables to the rear of the ACU.

5. Use a pencil to mark the 4 hole positions (two on each side), and

use the appropriate drill bit to drill.

20

Intellian Satellite TV Antenna Systems

After installing and mounting the antenna, connect the ACU to the

antenna. Refer the drawing on the right to connect the cables.

Single IRD Connection

1. Connect the RF cable 49ft (15m) from the RF 1 connector on the

antenna base plate to the ANT. RF1 connector on the ACU.

2. Connect the RF cable 10ft (3m) from the RECEIVER connector on the

ACU to RF connector on the IRD.

3. Connect the DC power cable 33ft (10m) from DC power connector on

the ACU to a power source from 9~30 V DC.

4. Press the POWER ON switch on the ACU to start the operation of the

antenna system.

Figure 17 : Single IRD Conguration

NMEA

ANT RF1 RECEIVER

FUSEDC 9~30V PC INTERFACE

FG - +

+ -

RF1 RF2

RF Cable

DC

Power

Cable NMEA

GPS

PC

Cable

ACU

IRD (Not Supplied)

Connecting the System Cables of i3/i3L/i4/i4P

Page is loading ...

Intellian i4P User manual

Intellian i4P User manual

Related papers

Other documents