Ganz ZN-DNT350VE Osd Menu Control Manual

Category
Security cameras
Type
Osd Menu Control Manual

This manual is also suitable for

ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 1
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 2
Table of Contents
1.ZNDWNT350VE(WDR/TrueDay&Night) ............................................................3
1.1.Menu .................................................................................................................................. 3
1.2.Howtoset .......................................................................................................................... 4
1.2.1.LENS............................................................................................................................. 6
1.2.2.EXPOSURE ................................................................................................................... 7
1.2.3.WhiteBalance ............................................................................................................. 9
1.2.4.BACKLIGHT ................................................................................................................ 10
1.2.5.DNR(DigitalNoiseReduction) .................................................................................. 12
1.2.6.DAY/NIGHT ................................................................................................................ 13
1.2.7.IMAGEADJ................................................................................................................ 14
1.2.8.SPECIAL...................................................................................................................... 16
1.2.9.EXIT............................................................................................................................21
1.3.Specification .................................................................................................................... 22
2.ZNDT350VE(SWDay&Night) ............................................................................. 23
2.1.Menu ................................................................................................................................ 23
2.2.Howtoset ........................................................................................................................ 24
2.2.1.LENS........................................................................................................................... 26
2.2.2.SHUTTER.................................................................................................................... 27
2.2.3.WHITEBALANCE........................................................................................................ 28
2.2.4.BACKLIGHT ................................................................................................................ 29
2.2.5.AGC............................................................................................................................ 30
2.2.6.DNR(DigitalNoiseReduction) .................................................................................. 31
2.2.7.SENSUP(Lowillumination) ...................................................................................... 32
2.2.8.SPECIAL...................................................................................................................... 33
2.3.Specification ..................................................................................................................... 38
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 3
1. ZN-DWNT350VE (WDR / True Day & Night)
1.1. Menu
SETUP
LENS DCMANUAL
EXPOSURE
SHUTTERAGCSENSUP
RETURN
WHITEBALANCE
ATWMANUALAWCSET
OUTDOORINDOOR
BACKLIGHT
OFFWDRBLC
HLC
DNR ONOFF
DAY/NIGHT
COLORB/WAUTO
EXTERN
IMAGEADJUSTMENT
FREEZEVREVHREV
DZOOMSHARPNESS
RETURN
SPECIAL
CAMTITLESYNCMOTIONDET
PRIVACYDISCOMMADJ
LANGUAGERESETRETURN
EXIT
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 4
1.2. How to set
Settings can be made using the 5 buttons located in the webpage. Go to [Setup]‐[Video &
Audio][Videoinput]andyoucanseethepageofbelow.
1.PresstheSETbutton.
TheSetupmenuisdisplayedonthemonitorscreen.
ClickPREVIEWbuttontopopuptheimageview
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 5
2.SelectamenuitemusingtheUpandDownbuttons.
Placethecursoroveradesireditem.
3.SetupaselecteditembyusingtheLeftandRightbuttons.
4.Tofinishandsavethesettings,select'EXIT'andpresstheSETbutton.
NOTE:
Anitem
withthe iconalsohassubmenus.Toselectasubmenu,presstheSETbutton.
Anitemwiththe‐‐‐iconhasnosubmenusavailableforselection.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 6
1.2.1. LENS
Thisfunctionisusedtoadjustthebrightnessofthescreen.
1. When the SETUP menu screen is displayed on the screen, position the cursor to point to
LENSusingtheUpandDownbuttons.
2.SelectthetypeoflensusingtheLeftandRightbuttons.
DC:
SelectAutoIrisLens
When DC is selected, you can control screen brightness. The range of brightness control is
between1and70(40 incaseofWDRmode).Adjustthebrightnessappropriatelyforoptimal
screenbrightness.
NOTE:
Somelensesmaynotworkproperly,dependingonthesettingsfor
theBRIGHTNESSLEVEL.
WhenUsingaVideoTypeAutoIrisLens
CheckthattheALCadjustmentonthelensisappropriate.Ingeneral,setittoAV(Average).
Itmaynotworkproperlydependingontheinstalledlens.SettheLevelVRofthelenstothe
optimalvalue.
SetAGC/SENSUPtoOFFandadjusttheLensVRtoanappropriatebrightness.
Adjust the Lens VR, adjust the BRIGHTNESS, and then check if the screen brightness
changesproperly.Otherwise,adjusttheLensVRagain.
Manual:SelectManualLens
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 7
1.2.2. EXPOSURE
1.WhentheSETUPmenuscreenisdisplayedselectEXPOSUREusingtheUpandDownbuttons.
2.SelectthedesiredmodeusingtheLeftandRightbuttons.
SHUTTER:Selecteitherautoormanualshutter.
‐A.FLK:Selectthiswhenpictureflickerisexperienced,whichcanhappenwhen
thereisacl ash
withthefrequencyoftheinstalledlighting.
‐ ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter
speedisautomaticallycontrolledaccordingtotheambientilluminationavailable.
‐MANUAL:Theshutterspeediscontrolledmanually.
NOTE:
To
producebetterresultswithA.FLK,donotuseitinconjunctionwiththeWDRmodeonthe
BACKLIGHTmenu.
When the SHUTTER is set to ESC, and the camera is set to Internal Synchronization, the
picture may become unstable if the camera faces a bright fluorescent light. Therefore, take
carewhenchoosingtheinstallationposition.
ESCandMANUALmodesareonlyavailabletogetherwhen thelensissettoMANUAL.
WhentheSHUTTERissettoMANUALorA.FLKmode,SENSUPisdisabled.
AGC(AUTOGAINCONTROL):
Thehigherthegainlevel,thebrighterthescreen
‐butthehigherthenoise.
‐OFF:DeactivatestheAGCfunction.
‐LOW:Allowsautomaticgaincontrolfrom0to24dB.
‐HIGH:Allowsautomaticgaincontrol from0to42dB.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 8
SENSUP:
Whenitisnightordark,thecameraautomaticallydetectsthelightlevelandmaintainsaclear
pictureifthismodeisa ctivated.
‐OFF:DeactivatestheSENSUPfunction.
‐AUTO:ActivatestheSENSUPfunction.
RETURN:
Selectthistosave
thechangesintheEXPOSUREmenuandreturntotheSETUPmenu.
NOTE:
If you press the SET button in 'AUTO' mode, You can adjust brightness by increasing or
decreasingtheshutterspeed.(X2~X256)
Notethatthehigherthezoom level,thebrighterthescreen,butthemore
likelyitisthatan
afterimagewillappear.
Although Noise, Spots, and Whitish symptoms may occur in SENSUP operation when the
zoomlevelisincreased,thisisnormal.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 9
1.2.3. White Balance
UsetheWhiteBalancefunctiontoadjustthescreencolors.
1.Position the cursor to point to WHITEBAL on the SETUP menu screen,select using the Up
andDownbuttons.
2.SelectadesiredmodeusingtheUpandDownbuttons.
Selectoneofthefollowing5modes,as
appropriate.
ATW:Selectwhenthecolortemperatureisbetween1800°Kand10500°K
INDOOR:Selectwhenthecolortemperatureisbetween4500°Kand8500°K
OUTDOOR : Select when the color temperature is between 1 800°K and 10500°K. (sodium
lightinclusion)
AWC SET : To obtain the
optimum state under the current luminance levels, direct the
camerato point towarda sheetof whitepaperandpresstheSETbutton. If theenvironment
changes,includingthelightsource,thewhitebalancewillrequirereadjustment.
MANUAL : Select to "finetune" the White Balance manually. Set White
Balance first using
theATWorAWCmode.AfterwardsswitchtoMANUALmode,finetunetheWhiteBalancean d
thenpresstheSETbutton.
NOTE:
Under the following conditions White Balancemaynotwork properly. In suchcases, select
theAWCmode.
Whenthecolortemperature
ofthesubjectenvironmenthasaveryhigh temperaturerange
(e.g.Clearskyorsunset)
Whentheambientillumination ofthesubjectislow.
If the camera is directed toward a fluorescent light, or is installed in a place where
illuminationchangesdramatically,theWhiteBalanceoperationmaybecomeunstable.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 10
1.2.4. BACKLIGHT
Thiscameraisdesignedtodeliveraclearanddistinct imageofbothsubjectandbackground,
evenwhenthesubjectisbacklit.
1. Position the cursor to point to BACKLIGHT on the SETUP menu screen using the Up and
Downbuttons.
2.SelectthedesiredmodeusingtheLeftandRightbuttons.
WDR:Whentheimagehassimultaneousbrightanddarkareas,the
WideDynamicRangemakesbothareasdistinct.
OFF:DeactivatestheWDRfunction.
BLC:Enablestheusertodirectlyselectanareaof
apicturetoactivateandcontrol.
HLC(HighLightCompensation):
Ifthereisahighlightinstalled inalimitedenvironmentsuchasanapartment parkinggarage
or gas station entrance, removing the high light makes it possible to view car license plates
efficiently.
‐DAY:Innormal
daylightconditions,theHLCisnotactivated.
‐NIGHT:Ifa highlightthat islarger thana certainsizeispresenton thescreen, removethe
highlighttoseelicenseplatesclearly.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 11
3.SelectthedesiredmodeusingtheLeftandRightbuttonsandpresstheSETbutton.
NOTE:
The WDR cannot be used when MANUAL mode or A.FLK mode in the 'SHUTTER' menu is
selected.
IfthefollowingsymptomsoccurwhenWDRisselected,deactivateit.
Colorofscreenchangesunnaturally.
Noiseappearsinthebrightestpartofthescreen.
As the performance of the WDR function can be affected by an area of brightness on the
image,optimizetheinstallationangletoeliminateanybrightspotsforthebestperformance.
IfLIMIT
isincreased,theimagemaybecomedistorted.
ForthebestWDRperformanceuseaDCIrisLensratherthanaManualLens.
Select 'WDR' to adjust the WDR
LIMIT. Select LOW, MIDDLE, or
HIGH.
Select 'BLC' to adjust the area to be
enhancedbytheWDRfunction.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 12
1.2.5. DNR (Digital Noise Reduction)
Thisfunctionreducesthebackgroundnoiseinalowluminanceenvironment.
1. WhentheSETUPmenuscreenisdisplayed,select'DNR'usingtheUpandDownbuttons.
2.SelectadesiredmodeusingtheLeftandRightbuttons.
OFF:DeactivatesDNR.Noiseisnotreduced.
ON:Activates
DNRsothatnoiseisreduced.
3.SettheDNRmod e to'ON'andpresstheSETbutton.Thenoisereductionlevelcan nowbe
adjusted.
NOTE:
YoucannotsettheDNRto'ON'or'OFF'whentheAGCmodeintheEXPOSUREmenuis'OFF'.
WhenadjustingthenoisereductionlevelinDNRmode,rememberthatthehigherthelevelis
set,thegreaterthereductioninnoiselevel,butitalsoincreasesthepossibilityofghosting.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 13
1.2.6. DAY/NIGHT
Picturescanbedisplayedineithercolororblackandwhite.
1. When the SETUP menu screen is displayed, select 'DAY/NIGHT' using the Up and Down
buttons.
2.SelectthedesiredmodeusingtheLeftandRightbuttons.
COLOR:Thepictureisdisplayedincolor.
B/W:
Thepictureisalwaysdisplayedinblackandwhite.
AUTO:ThiscamerahasanIRCutFilterandautomaticallychangestotheappropriatemode
according to lighting levels. To set up the switching time and switching speed for the AUTO
modepresstheSETbutton.
EXTERN:
Thismodeallowstheapplicationofafiltertoexternalsignals.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 14
1.2.7. IMAGE ADJ.
1. When the SETUP menu screen is displayed, select 'IMAGE ADJ.' using the Up and Down
buttons.
2.SelectthedesiredmodeusingtheLeftandRightbuttons.
FREEZE:Viewandcaptureastillimage.
VREV:Flipsthepictureverticallyonthescreen.
HREV:Flipsthepicturehorizontallyonthescreen.
DZOOM:Digitallyzooms,therangeisx1~x10.
SHARPNESS:Asthisvalueisincreasedthepictureoutlinebecomesstrongerandclearer.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 15
RETURN : Select this to save the settings for the IMAGE ADJ. menu and to return to the
SETUPmenu.
Note:
WhenHREVorVREVisselected,anytextinthepicturealso willbeflippedhorizontallyor
vertically.
IftheSHARPNESSlevelis
increasedtoohighthe picturemaybecomedistorted,ornoisemay
generated.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 16
1.2.8. SPECIAL
1.WhentheSETUPmenuscreenisdisplayed,select'SPECIAL'usingthe
UpandDownbuttons.
2.SelectthedesiredmodeusingtheLeftandRightbuttons.
CAMTITLE:Ifatitleisentered,thetitleappearsonthemonitor.
When the SPECIAL menu screen is displayed, use the Up and Down buttons to point the
cursorto'CAMTITLE'.
Setto'ON'usingtheLeftandRightbuttons.
NOTE:
WhentheCAMTITLE
menuis'OFF',notitlewillbedisplayedonthemonitorscreenevenifone
hasbeenentered.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 17
PresstheSETbutton.
Use the 4 directional buttons to move to a character, and select it by pressing the SET
button.Repeatthisactiontoentermultiplecharacters.Upto15alphanumericcharacterscan
beused.
If the cursor is moved to CLR and the SET
button pressed, allletters are deleted. To edit a
letter,changethecursortothebottomleftarrowandpresstheSETbutton.Movethecursor
over the letter to be edited, move the cursor to the letter to be inserted and then press the
SETbutton.
Enteratitl e,
movethecursorto'POS'andpresstheSETbutton.Theenteredtitleappears
on the screen. Select the position to display the title on the screen using the 4 directional
buttonsandpresstheSETbutton.Whenthepositionisdetermined,select'END'andpressthe
SETbuttonto
returntotheSPECIALmenu.
SYNC:Inareaswherethesupplyis60Hz,multiplecamerasusingthepowersynchronization
function(LineLock),withoutusingasynchronizationsignalgenerator.
‐INT:InternalSynchronizationType
‐L/L:PowerSynchronizationType,Linelock
PresstheSETbutton.
Selectaphasebetween0and359.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 18
NOTE:
WhenusingACpowerata60HzfrequencyLineLocksynchronizationcanbeused.
WhenthepowerisDC12V,theSYNC.menuisfixedtothe'INT'mode.
MOTIONDET:
Thiscameradisplaysanonscreenmessagewhenevermotionisdetected.
When the
SPECIAL menu screen is displayed, press the Up and Down buttons so that the
cursorpointstoMOTIONDET.
Setupthefunctionusingthe4directionalbuttons.
‐ SENSITIVITY : Select up to eight MD areas. When the SENSITIVITY value is high, motion
detectionsensitivityisincreasedtorecognize
smallmovements.
‐AREAMODE:DetermineswhethertousetheMDareaselectedinSENSITIVITY.
‐SELPOS:Determineswhichofthe4verticesofeachMDareaistobeused.
‐YPOS:Determinesthecoordinates oftheverticalaxisforSELPOS.
‐XPOS:Determinesthe
coordinatesofthehorizontalaxisforSELPOS.
‐ FILL SET : Fills in a selected MD area. Fill in a selected MD area. The color of filling is
sequentiallyselectedasbrown,orange,blue,cyan,ye llowishgreen,yellowandred.
‐RETURN:SelectthistosavetheMOTION
DETmenusettingsandreturntotheSPECIALmenu.
NOTE:
MDareas show onlyon the MOTION DET menu. Therefore,MDareas are notdisplayedon
themonitorscreen.
PRIVACY:Hideanareasothatitisnotdisplayedonthemonitor.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 19
‐MASKCOLOR:Determineareacolor.SelectGrey,Green,Red,Blue,BlackorWhite.
‐TRANSP:Determinethetransparencyoftheselectedarea,therangeisfrom0to3.
‐RETURN:SelectthistosavethePRIVACYmenusettingsandreturntotheSPECIALmenu.
DIS(Digital
ImageStabilizer):
Thisfunctionmitigatespicturemovementcausedbyexternalfactors,suchaswind.
COMMADJ(CommunicationAdjustment) :
Thisfunctionsetsupthe cameracommunication statuswhencontrollingthecamerathro ugh
anexternaldevice.
When the SPECIAL menu screenis displayed, press the UpandDown
buttons so that the
cursorpointsto'COMMADJ'.
Setupthemodeusingthe4directionbuttons.
‐CAMID:Determinesthecamera'side ntificationnumber(between0and255).
‐BAUDRATE:Select2400/4800/9600/19200/38400/57600bps.
‐UARTMODE:SelectNONE,EVENorODDfortheparitybits.
‐
RET PKT : Determines whether to send a command back to the controller device when a
communicationcontrolcommandissenttothecamera.
When the SPECIAL menu screen is
displayed, press the Up and Down
buttons so that the cursor points to
'PRIVACY'.
Setupusingthe4directionalbuttons.
‐AREASEL:Upto8areasareselectable.
‐AREAMODE:Determineswhethertouse
theareaselected inthe
AREASEL,and the
sizeandpositionofthearea.
ZNDT350VE/ZNDNT350VE/ZNDWNT350VEOSDMenuControlManual
2010/2103A.00 20
‐DISPCAMID:Displaythecameratitleonthetopleftcornerofthescreen.
LANGUAGE:Selecttheappropriatemenulanguage.
RESET:Resetsthecamerasettingstothefactorydefaults.
RETURN:SelectthistosavetheSPECIALmenusettingsandreturntothe
SPECIALmenu.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Ganz ZN-DNT350VE Osd Menu Control Manual

Category
Security cameras
Type
Osd Menu Control Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI