Vacron Full HD SDI Camera User manual

i

FULL HD-SDI

Color Camera with 1080P

2013. V1.0

User Manual

i

Safety Precautions

Before using the product, please ensure that you read the safety

precautions described below. Always ensure that the product is used

correctly.

• Use only recommended power sources.

• Do not attempt to disassemble, alter or apply heat to the product.

• Avoid dropping or subjecting the product to severe impacts.

• To avoid the risk of injury, do not touch the interior of the product if it has been

dropped or otherwise damaged.

• Stop using the product immediately if it emits smoke, a strange smell, or otherwise

behaves abnormally.

• Do not use organic solvents such as alcohol, benzene, or thinner to clean the

product.

• Do not allow liquids or foreign objects to enter the camera.

• Do not place the camera near or in direct flame.

• Do not handle the power cord with wet hands.

• Do not use the equipment in a manner that exceeds the rated capacity of the

electrical outlet or wiring accessories. Do not use if the power cord or plug are

damaged, or not fully plugged into the outlet.

• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals or

plug.

ii

Index

1. Feature ................................................................................................................. 1

2. Specifications ....................................................................................................... 2

3. OSD Function ...................................................................................................... 4

4. Operation specification of OSD Menu .................................................................. 6

(4.1) Normal Display (when OSD off) ...................................................................... 6

(4.2) Main Menu ...................................................................................................... 7

(4.2.1) LENS/EXPOSURE SETUP ...................................................................... 8

(4.2.2) BLC / DNR SETUP ................................................................................... 9

(4.2.3) WHITE BALANCE SETUP ..................................................................... 11

(4.2.4) DAY/NIGHT SETUP ............................................................................... 12

(4.2.5) MOTION SETUP .................................................................................... 13

(4.2.6) PRIVACY SETUP ................................................................................... 16

(4.2.7) PICT ADJUST SETUP ............................................................................ 18

(4.2.8) OPTION SETUP ..................................................................................... 18

(4.2.9) CAMERA SETUP ................................................................................... 20

1

1. Feature

(1) 1/2.8 "CMOS 1080P Full HD-SDI Color Camera.

(2) 2 Mega-Pixels High Resolution Color 1080P.

(3) Support 1080P Full HD-SDI High-

(4) Definition Digital Signal Output.

(5) Digital Noise Reduction Function(2D / 3D-NR).

(6) Electronic Shutter Speed: Auto, 1/30S~1/50,000S.

(7) Sensitivity Increase (Slow Shutter): x2~x30(Max).

(8) Digital Wide Dynamic Range (ACCE).

(9) Multiple level Setting for Defogging (DEFOG).

(10) Back Light Compensation (BLC),High Light Compensation (HLC).

(11) Image Rotation Function(0~360°).

(12) Image Freeze Function (FREEZE).

(13) Digital Zooming (Zoom-in X64).

(14) Intelligent Motion Detection (Motion).

(15) Eight Privacy Mask Spots (Color x16).

2

2. Specifications

Video System NTSC PAL

Pick Up Element 1/2.8” CMOS 2 Mega-Pixel Image Sensor

Image Signal Process Digital Signal Processor

Number of Pixels 1936 (Horizontal) x 1097(Vertical)

Horizontal Resolution Color: 1080P/30fps

Power Supply DC12V

Power Consumption 650mA

Lens Mount 2.8 mm ~ 12 mm (Vari-Focal)

Mechanical IR Cut Filte

r

Automatically Switches (IR Board Control)

Scanning System Progressive Scanning

Sensitivity 0 Lux(IR ON)

OSD Menu Build-in OSD Menu

Camera Name/Function

Display

Camera Name Display / Function Display

Digital Zoom Off/On (Max X64)

WDR Digital Wide Dynamic Range (Off/High/Mid/Low)

Digital Anti-fog

processing

(Off/High/Mid/Low)

Back Light

Compensation

HLC / BLC / Off

Auto-Gain Control (High/Mid/Low)

Digital Noise

Reduction(DNR)

2D/3D-NR

Digital Zoom Color/ Black &White/Auto+Delay

Motion Detection Off/On (3 Areas Setting)

Privacy Mask On/Off (8 Editable Area and 16 Color Choices)

AWB ATW/AWC/Manual/Indoor/Outdoor

Languages English/Simplified Chinese/Traditional Chinese/ Japanese

Electronic Shutter

Speed

SHUTTER : AUTO, 1/30S, 1/60S, FLK, 1/250S,

1/500S,1/1,000S,

1/2,000 S, 1/5,000 S, 1/10,000, 1/50,000S

SLOW SHUTTER: x2, x4, x6, x8, x10, x15,x20, x25,

x30

3

LEDS 70PCS

IR Range

60 m

Video Signal Output SDI Signal Output (Serial Digital Interface), 75 Ohms

Standard Video Signal

Output

CVBS 1Vp-p (BNC connecter 75 Ohms)

Uniaxial Coaxial Cable HD over 100m of RG59

Temperature

- 5℃ ~ +40℃

4

3. OSD Function

MENU SUBMENU NOTE

LENS/EXPOSURE

1. ALC/AES

Please refer to

6.2.1 LENS /

EXPOSURE

SETUP

2. SHUTTER

3. IRIS GAIN

4. AGC

5. SENSE

BLC/DNR

1. BLC MODE

Please refer to

6.2.2 BLC / DNR

SETUP

2. BLC AREA

3. BLC LEVEL

4. 3D-DNR MODE

5. 3D-DNR LEVEL

6. D-WDR

WHITE BALANCE

1. WB MODE

Please refer to

6.2.3 WHITE

BALANCE SETUP

2. PUSH AUTO

3. MANUAL RED

4. MANUAL BLUE

5. ATW LEVEL

6. AWC LEVEL

DAY/NIGHT

1. D/N MODE

Please refer to

6.2.4 DAY / NIGHT

SETUP

2. D/N LEVEL

3. N/D LEVEL

4. D/N DELAY

5. SENSOR IN

MOTION

1. DETECT MODE

Please refer to

6.2.5 MOTION

SETUP

2. DETECT AREA

3. SENSITIVITY

4. ALARM TIME

5. ALARM DISPLAY

PRIVACY

1. AREA

Please refer to

6.2.6 PRIVACY

SETUP

2. MASK

3. MODE

4. LEVEL

5. POS

6. SIZE

5

MENU SUBMENU NOTE

PICT ADJUST

1. NEGA/POSI

Please refer to

6.2.7 PICT

ADJUST SETUP

2. SHARPNESS

3. BRIGHTNESS

4. R-Y GAIN

5. B-Y GAIN

6. ROTATE/FLIP

OPTION

1. DIS

Please refer to

6.2.8 OPTION

SETUP

2. D-ZOOM

3. PAN/TILT

4. PAN/TILE POS

CAMERA SET

1. TITLE

Please refer to

6.2.9 CAMERA

SET SETUP

2. TITLE DISPLAY

3. MONITOR

4. COMMUNICATION

5. LANGUAGE

6. INITIAL

END -- Exit OSD

 Enter：The Enter switch has the meaning of the decision in the ON/OFF

submenu of OSD. It is necessary to push a little long, and no auto repeat.

 UP / Down：UP/Down switch select item (Auto-repeat).

 LEFT / Right：LEFT/Right switch change item (Auto-repeat).

 Auto power off : If switch is not operated for one minute, OSD is turned off.

6

4. Operation specification of OSD Menu

(4.1) Normal Display (when OSD off)

Normal Display: In the normal screen of the camera, the following displays

can be put out by the selection.

a. MD: MOTION DETECT DISPLAY AREA

When the function of "Motion Detect" and the "MOTION DISPLAY "is

display on, "MD" is displayed on.

b. TITLE: Camera Title Display Area

When the "CAMERA TITLE" is set, and the "TITLE DISPLAY" is set on,

the camera title is displayed.

Moreover, the display can select "upper left"," upper right", "lower left"

and "lower right".

c. ID: Communication ID display area.

When "COMMUNICATION ID DISPLAY " is selected, ID Number is

displayed on.

7

(4.2) Main Menu

In the main menu, each submenu is selected.

 Enter: Exit from On Screen Display.

 UP/ Down: Change Sub Menu Selection.

 Right / Left: Select Sub Menu.

Submenu Function explanation

LENS/EXPOSURE Transition to the LENS/EXPOSURE Screen.

BLC/DNR Transition to the BLC/DNR Screen.

WHITE BALANCE Transition to the WHITE BALANCE Screen.

DAY/NIGHT Transition to the DAY/NIGHT Screen.

MOTION Transition to the MOTION Screen.

PRIVACY Transition to the PRIVACY Screen.

PICT ADJUST Transition to the PICT ADJUST Screen.

OPTION Transition to the OPTION Screen.

CAMERA SET Transition to the CAMERA SET Screen.

END Exit.

8

(4.2.1) LENS/EXPOSURE SETUP

LENS/Exposure Menu sets it with the selection concerning brightness.

a. ALC/AES

 ALC : Auto Lens Control Select (DC-LENS Support).

 AES : Auto Electrical Shutter Control Select.

b. SHUTTER

 Select Electrical shutter speed, when ALC mode. In the AES mode, It

is not possible to set it.

 OFF/FLC/125/250/500/1000/2500/5000/10000/30000

c. IRIS GAIN

 Lens(offset): When ALC, The DC offset of the “DC lens” is adjusted.

The level of ALC/AES is made the same.

 Lens(Gain): When ALC, The gain of the “DC lens” is adjusted.

It is noted that the lens-hunting and lens-Immovable.

d. AGC

Select the level of the AGC. MIN / 3 / 6 / 9 / 12 / 15 / 18 / 21 / 24 / 27 / 30 /

33 / 36 / 39 / 42 / MAX.

e. SENSE

(remark 1)

 Sensitivity by Slow-scan improves, the limit value is set. OFF / x2 / x4 /

x6 / x8 / x12 / x16 / x32 / x64 / x128 / x255

remark 1.

DESCRIPTION : Increase sensitivity by long exposure and

achieved bright image. Even though shot in dark place. However, the update of

the image slows.

 Enter: Exit from On Screen

Display.

 UP / Down: Change item

Selection.

 Right / Left: Select Each

mode, Each Value.

9

(4.2.2) BLC / DNR SETUP

The selection and the level of items as follows are set.

BLC(Back Light Control)

3D-DNR(Digital Noise Reduction)

HLC(High Light Control)

D-WDR(Digital Wide Dynamic Range Control)

a. BLC MODE

Select BLC function.

 OFF

 ON: Select BLC function.

 HLC: Select HLC function.

b. BLC AREA

Transition to the BLC Available Area Sub MENU. When BLC MODE is OFF,

it is not possible to select.

BLC effective area is selected.

 Enter: Exit from BLC SUB MENU.

 UP / Down: Change Effective and invalidity. Gray Area is invalidity.

Transparent area is effective.

 Enter: Exit from On Screen

Display.

 UP / Down: Change

item Selection.

 Right / Left: Select

Each mode, Each Value.

10

 Right: Select next area.

 Left: Select previous area.

c. BLC LEVEL / HLC LEVEL

 BLC LEVEL

Select BLC function level(Operational when BLC MODE is ON).

-1: (weak) ~ 0: (Default) ~ +2: (strong)

When BLC MODE is HLC, this item changes HLC LEVEL.

 HLC LEVEL

(remark 5)

Select HLC function level (Operational when BLC MODE is HLC).

MIN/-28/-24/-20/-16/-12/-8/-4/MID/+4/+8/+12/+16/+20/+24/+28/MAX

remark 5.

Possible to see car number plate and other more visible by level control of

halation part such as headlight, and so on.

This function becomes effective when it is dark.

d. 3D-DNR MODE

3D-Digital Noise Reduction mode select.

 OFF this function off.

 ON It is always controlled.

 AUTO It is controlled darkness when it is dark.

e. 3D-DNR LEVEL (remark 3)

When 3D-DNR MODE is ON or AUTO, 3D-DNR reduction level change.

LOW/MID/HIGH

remark 3.

Smoothed dark part of noise by pixel of plural pieces field, and moreover,

Achieved image of lowering noise.

11

f. D-WDR (remark 4)

Select D-WDR function. OFF/LOW/MID/HIGH

remark 4.

When the high luminance part and the low illumination part are detected,

the suppression low illumination part is raised, and a high luminance part is

adjusted in the contrast.

(4.2.3) WHITE BALANCE SETUP

Setting of White balance mode. Setting of each color temperature setting and

the Color density is set.

a. WB MODE

White Balance mode setting.

 ATW1: Auto Tracking White Balance.

 ATW2: Auto Tracking White Balance (a drawing in limitation of the

color).

 AWC: Auto White Balance Control (One-Push White Balance).

 Enter: Exit from On Screen

Display.

 UP / Down: Change

item Selection.

 Right / Left: Select Each

mode, Each Value.

12

 MANUAL: User Definition.

 INDOOR: The indoor mode setting.

 OUTDOOR: The outdoor mode setting.

b. PUSH AUTO

When AWC mode, Push “Right/LEFT” switch, WB is controlled during the

fixed time. Became “STOP” , White Balance Fixed.

c. MANUAL RED

When MANUAL mode, Red strength is set. (0~127)

d. MANUAL BLUE

When MANUAL mode, Blue strength is set. (0~127)

e. ATW LEVEL

The settling point at ATW is set. (RED+3~MID~BLUE+3)

f. AWC LEVEL

It shifts from the point settled with AWC. (RED+3~MID~BLUE+3)

(4.2.4) DAY/NIGHT SETUP

When Day/Night Lens use, DAY/NIGHT mode setting, and Each setting. In Night

mode, Color is only Black and White.

a. D/N MODE

Select of the D/N MODE.

 AUTO: Day/Night auto change mode.

 DAY: DAY mode.

 NIGH: Night mode.

 EXT: External Input pin use.

b. D/N LEVEL

When D/N auto mode, Day to Night mode dark level setting.

0: (Light)~48:(Dark)(Changes in three increments.)

c. N/D LEVEL

When N/D auto mode, Night to Day mode light level setting.

0: (Light)~48:(Dark)(Changes in three increments.)

 Enter: Exit from On Screen Display.

 UP / Down: Change item

Selection.

 Right / Left: Select Each

mode, Each Value.

13

d. D/N DELAY

When D/N auto mode 4 / 5 / 6 / 7 / 8 / 9 / 10 / 15 / 20 / 25 / 30 / 40 / 50 / 60

SEC.

e. SENSOR IN

When EXT mode, External pin polarity.

 NO: Positive polarity.

 NC: Negative polarity.

(4.2.5) MOTION SETUP

Motion detect mode, and detect mode each setting.

a. DETECT MODE

Select of the Motion Detect mode.

 OFF

 SIMPLE Motion detection by brightness variation.

 TRACE Motion detection by moving object follow.

 IN-OUT Motion detection by A-area to B-area or B-area or B-area to

A-area.

 Enter: Exit from On Screen

Display.

 UP / Down: Change item

Selection.

 Right / Left: Select Each

mode, Each Value.

14

b. DETECT AREA

Transition to the Motion detect area Screen.

The Motion detect area is selected. The selection method is different

depending on the mode.

(1) In case of Motion detect is all mode. Effective area are specified.

 Enter: Exit from this SUB MENU.

 UP/ Down : Change effective and invalidity. Gray Area is

invalidity. Transparent area is effective.

 Right: Select next area.

 Left: Select previous area.

(2) In case of Motion detect is “IN-OUT”. The boundary in the A/B area is

specified.

15

 Right: Select the angle of the boundary.

 Down: Select the vertical boundary.

 UP: Select the horizontal boundary.



Enter:

Transition to the Effective area Screen.

Push Enter again, transition to the MOTION Screen.

16

c. SENSITIVITY

Motion Detect sensitivity select.

0: (weak) ~ 8 : (sensitive)

d. ALARM TIME

When detect move object, alarm display, continuous time. 1 / 2 / 3 / 4 / 5 / 6 /

7 / 8 / 9 / 10 / 15 / 20 / 25 / 30 / 40 / 50 / 60 SEC.

e. ALARM DISPLAY

When detect move object, alarm display.

 OFF: no display on screen.

 ON: “MD” display on screen.

(4.2.6) PRIVACY SETUP

PV-MASK is set and the level and the area are set according to the mode.

a. AREA

The set MASK number is selected. (1 ~ 24)

b. MASK (remark 5)

It sets whether to make the specified MASK number effective or to invalidate

it. OFF: Invalidity ON: available

remark 5.

Possible to mask part where not to shot. Provide Black, White, Color and

Mosaic. The number of Privacy mask area that can be set is 24 or less.

 Enter: Exit from On Screen

Display.

 UP / Down: Change item

Selection.

 Right / Left: Select Each

17

c. MODE

The mode of MASK is selected.

 BW: Black/White select.

 MOSAIC: Mosaic select.

 COLOR: Color select.

d. LEVEL

The level by each mode is set.

 In case of B/W

0:(Black) ~ 15:(White)

 In case of MOSAIC

SMALL/MIDDLE/LARGE

 In case of COLOR

RED/BLUE/BLACK/WHITE/YELLOW/CYAN/GREEN/MAGENTA

e. POS

Transition to the PRIVACY MASK POSITION Screen.

DESCRIPTION :

PRIVACY MASK POITION

Position of the PV-MASK are set.

f. SIZE

Transition to the PRIVACY MASK SIZE Screen.

 PRIVACY MASK SIZE

Size of the PV-MASK are set.

 Enter: : Determines the

position of the PV-MASK and

exit from On Screen Display.

 Up / Down /

 Right / Left

Change the position of the

PV-MASK.

 Enter: Determines the

size of the PV-MASK and

exit from On Screen Display.

 Up / Down /

Right / Left: Change

the size of the PV-MASK.

Page is loading ...

Vacron Full HD SDI Camera User manual

Vacron Full HD SDI Camera User manual

Related papers

Other documents