Models 2435, 2435LN, 2437 (3:1 ratio)
Models 2535, 2537 (5:1 ratio), 16 gal. (72 l) drum size
Stationary gear lubrigun
User and maintenance instructions
Date of issue August 2017
Form number 403465
Version 2
Contents
Assembly . . . . . . . . . . . . . . . . . . . . . . . . 3
Exploded view . . . . . . . . . . . . . . . . . . . . 3
Service parts . . . . . . . . . . . . . . . . . . . . . 4
Warranty . . . . . . . . . . . . . . . . . . . . . . . . 8
2
7
2
3
4
5
6
9
10
12
6
19
1
11
20
13
14
15
18
17
8
16
1)
2)
2)
Fig. IPB 1
Assembly
1 Assemble hanger control valve (20) to
drum cover (17).
2 Assemble pump (9) to drum cover
top (17) with four screws (14).
3 If pumping heavy grease that requires a
follower, place an optional follower into
grease in open 120 lb. (54 kg) drum.
4 Place drum cover assembly (17) onto
drum while placing tube through
follower, if used. Screw in three thumb
screws (13) to secure drum cover to
drum.
5 Assemble outlet adapter (4) to air motor
inlet. Insert air nipple (3) into
adapter and tighten.
6 Assemble air hose (1) to air coupler (2)
and tighten.
7 If meter is used, connect union
adapter (12) and swivel adapter (10) to
pump outlet. Attach meter (8) to swivel
adapter (10) and tighten.
8 Attach volume hose assembly (11) to
outlet of meter and tighten.
9 If no meter is used, connect swivel
adapter (10) directly into pump outlet
and hose (11) into swivel adapter (10).
1)
1
/4 in NPTF
2)
1
/2 in NPTF
10 Assemble control valve (7), if used, to
outlet end of volume hose assembly (11)
and tighten.
11 Unit is operational when
air delivery hose (1) is connected
to pump (9).
note
Tighten all joints to ensure connections
will withstand air pressure.
3
Service parts
Item Description Part number Qty. Item Description Part number Qty.
1 Hose air assembly 72060 1 10 Swivel adapter 241584 1
2 Air coupler 815 1 11 Hose volume assembly 73060 1
3 Air nipple 11659 1 12 Union adapter 66883
10)
1
4 Outlet adapter 11348 1 13 Screw 50415
11)
3
5 Cover nut 11478 1 14 Hex head sems screw 50060 4
6 Cover pump assembly 85935 1 15 Tube suction assembly 85716 1
7 Valve control 780
1)6)7)
1 16 Truck assembly 80895
6)7)
1
8 Meter 870
2)6)
1 17 Drum cover kit 46007 1
Meter 873
3)7)
1 18 Hex nut 50754
11)
2
9 Basic pump assembly 282396
4)8)
1
Basic pump assembly 84933
5)9)
1 19 Hex head cap screw 50113
11)
2
20 Hanger control valve 45761
11)
1
1)
Refer to service page 404115.
2)
Refer to service page 403099.
3)
Refer to service page 422661.
4)
Refer to service page 404099.
5)
Refer to service page 404100.
6)
Included in models 2435 and 2535.
7)
Included in model 2435LN.
8)
Included in models 2435, 2435LN and 2437.
9)
Included in models 2535 and 2537.
10)
Included in models 2435, 2435LN and 2535.
11)
Included in 46007 drum cover kit.
4
This page left intentionally blank.
5
This page left intentionally blank.
6
This page left intentionally blank.
7
skf.com | lincolnindustrial.com
® SKF and Lincoln are registered trademarks of the SKF Group.
© SKF Group 2017
The contents of this publication are the copyright of the publisher and may not be reproduced (even
extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy
of the information contained in this publication but no liability can be accepted for any loss or damage
whether direct, indirect or consequential arising out of the use of the information contained herein.
August 2017 · Form 403465 Version 2
Warranty
The instructions do not contain any information on the warranty.
This can be found in the General Conditions of Sales, available at:
www.lincolnindustrial.com/technicalservice or
www.skf.com/lubrication.
/
