Webasto Telestart T70 Operating instructions

Type
Operating instructions
Ident-Nr. 670 78A 3/9906
Operating Instructions
Telestart T70
OFF
General
Programming Telestart Transmitters
The wireless Webasto-Telestart T70 unit enables Webasto heating units -
- Thermo Top, Thermo Top T, Thermo Top Z/C and Thermo TopE-tobeswitched on and
off from a distance of up to 600 m.
A mode change on the transmitter enables the vehicle fan for ventilating the vehicle
interior to be switched on and off in the same manner.
The receiver limits the operating time once the heater has been switched on by the
transmitter. Maximum coverage is achieved in open country. In built-up areas the range is
likely to be reduced. Each receiver can "learn" the codes of up to 3 transmitters.
1. Place batteries into the battery compartment of the transmitter.
2. Remove fuse 1A (black) from the heater's fuse holder (voltage interruption).
3. Wait at least 5 seconds.
4. Replace fuse in heater's fuse holder and within 5 seconds press the OFF button
on the transmitter for at least 1 second.
5. "Learning" is completed.
A second or third hand-held transmitter can be programmed in the same manner.
1A
25A
1
5
A
1
A
1A
25A
1
5
A
1
A
min. 5 sec. max. 5 sec.
min. 1 sec.
OFF
ON
Checking the batteries
Press the OFF button.
If LED lights up after 1 second for 0.5 seconds:
Batteries are okay.
If LED (orange light) is blinking after 1 second for 3 seconds:
Low battery charge.
- Warm up batteries to above 0°C.
- Replace batteries at the next opportunity.
If LED (orange light) lights up after 1 second for 5 seconds:
Batteries are discharged.
- Warm up batteries to above 0°C.
- Replace batteries.
Remedy:
Remedy:
Webasto Thermosysteme GmbH
Postfach 80 - D-82132 Stockdorf - Hotline (01805) 93 22 78
Hotfax (0395) 55 92-353 - http://www.webasto.de
Heating mode / Ventilation mode
Mode setting
Switch on heater or ventilation
Switch off heater or ventilation
Test mode
Depress the ON and OFF buttons simultaneously twice within
one second.
Upon the first actuation of the buttons, the LED will light up in
the preset mode.
Upon the second actuation, the LED will change its colour and
illuminate until the buttons are released.
If the ON and OFF buttons are not actuated for more than 1
second, the setting will be stored.
Hold the hand-held transmitter with the antenna in upright
position and push the ON button for 1 to 2 seconds.
NOTE:
In the 'heating' mode, the vehicle's heating system is to
be set to "warm" prior to leaving the vehicle.
In the 'heating' and 'ventilation' modes, the vehicle's fan
switch is to be turned to position 1 in the case of 3-
speed blower fans, and to position 2 in the case of 4-
speed blowers. In the case of infinitely variable fans
adjust to at least 1/3 of the fan's capacity.
Hold the hand-held transmitter with the antenna in upright
position and depress the OFF button for 1 to 2 seconds.
NOTE:
If the distance between the transmitter and the antenna
in the vehicle is less than 2 m, an overload condition
may occur and neither the heater nor ventilation can be
switched on or off.
Remedy: Cover antenna at the transmitter with your hand.
The transmitter enables you to select between the modes 'heating using the heater' or
'ventilation using the vehicle's fan'. The 'heating' mode is factory-set.
Simultaneously push the ON and OFF buttons within one
second and keep depressed.
- LED illuminates in red = 'heating' mode
- LED illuminates in green = 'ventilation' mode
The LED extinguishes when the buttons are released, or after
a period of 10 seconds.
2x
!
!
Checking and Setting the Operating Time
Checking the operating time
Setting the operating time
Return to the default setting
NOTE:
In the case of Thermo Top and Thermo Top T heaters, an operating time of 20 or
30 minutes has to be set in the 'heating' mode.
In the case of Thermo Top Z/C and Thermo Top E heating units we recommend
that the heating time be set in accordance with the driving time.
Example: The vehicle is used for travelling to work and back.
With a driving time of approx. 30 minutes (one way), we recommend setting an
operating time of 30 minutes.
The operating time of the heater or the vehicle's fan can be preset on the transmitter in
increments of 10 minutes. The operating time is factory-set at 30 minutes.
NOTE:
The first coded flashing signal that is emitted immediately
upon the third actuation of both buttons has to be included
into the count.
The LED flashes in accordance with the preset operating time.
Simultaneously actuate the ON and OFF buttons within one
second three times in rapid succession.
Actuating the OFF button causes the next operating time to be
called up.
The operating time will be saved to memory if no button is
pressed within 10 seconds, or as soon as the ON button is
pressed.
Simultaneously depress the ON and OFF buttons for approx.
10 seconds until the LED goes out.
No. of coded flashing signals
Operating time
1
10 min.
4
40 min.
2
20 min.
5
50 min.
3
30 min.
6
60 min.
3x
!
!
  • Page 1 1
  • Page 2 2

Webasto Telestart T70 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI