3A1885A
Instructions
Control Board Conversion Kit
For Airlessco LP Sprayers
IMPORTANT SAFETY INSTRUCTIONS
For detailed sprayer information and warnings, see
the Operation manual included with your sprayer.
ENG
ti17429a
Removal
NOTE: If unit has fitting (1), tube (17) and manifold (18).
1. Disconnect power cord from outlet.
2. Remove fitting (1) which connects terminal box (7)
to pump (2) and fitting (1).
3. Remove screws (6) to remove heatsink (3). Discon-
nect board wire connectors and motor wire connec-
tors, then disconnect ground wire (30) from terminal
box (7).
4. Remove wire strain reliefs (5, 31) and pull out the
wires from terminal box (7).
5. Remove two screws (8) then remove terminal box
(7) from motor (103).
6. If unit has fitting (19) instead of (1, 17, and 18),
remove fitting (19).
18
7
17
1
3
5
2
8
6
16
19
ti17430a
ti17428a
1
31
30
103
Assembly
3A1885A 3
Assembly
1. Remove screws (13) to detach new heatsink (12)
from new terminal box (14).
2. Hand-tighten screws (8) to attach new terminal box
(14) to motor (103).
3. Assemble tube fitting (1) to pump (2). Adjust posi-
tion of terminal box to align other fitting on tube (17)
with fluid manifold (18).
4. Use wrench to fully tighten screws (8).
5. Route cord wires and motor wires into terminal box
(14). Assemble strain relief (5) to terminal box.
6. Attach ground wire (15) to the inside of new terminal
box (next to power cord).
7. Connect cord wires, motor wires (route wires to con-
trol board according to Wiring Diagram) then tighten
screw (13) to secure heatsink (12).
8. If unit has filter (16), move filter from told terminal
box to new terminal box (14).
ti17429a
8
12
14
15
16
13
5
31
10
8
18
1
17
TO PLACE AN ORDER OR FOR SERVICE, contact your Airlessco distributor,
or call 1–800–223-8213 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Airlessco reserves the right to make changes at any time without notice.
This manual contains English. MM 3A1885
Airlessco, 3501 N. 4th Avenue, Sioux Falls, SD 57104
www.airlessco.com
05/2011
Wiring Diagrams
MOTOR WIRE (RED)
MOTOR WIRE (WHITE/BLACK)
MOTOR WIRE (BLACK)
LCD DISPLAY
POTENTIOMETER
TRANSDUCER PRESSURE
CONTROL
ON/OFF
SWITCH
POWER CORD (WHITE)
POWER CORD (GREEN)
CHASSIS GROUND
POWER CORD (BLACK)
MOTOR WIRE (RED)
MOTOR WIRE (WHITE/BLACK)
MOTOR WIRE (BLACK)
LCD DISPLAY
POTENTIOMETER
TRANSDUCER PRESSURE
CONTROL
ON/OFF
SWITCH
POWER CORD (BLACK)
POWER CORD (GREEN)
CHASSIS GROUND
POWER CORD (WHITE)
120V Motor
220V Motor
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
LG Electronics 3600 User manual
-
Wagner SprayTech 3000, 3500 User manual
-
Hitachi 309067 User manual
-
Oracom MAX 695 User manual
-
-
Graco 309063F User manual
-
Graco Inc. 249690 User manual
-
Graco 334598A User manual
-
-
Graco Inc. 308864G User manual
