LG Electronics 3600 User manual

SERVICE/OPERATION

MANUAL

001-778 AUG07

MANUAL

Spray & Stripe

Table of Contents

INTRODUCTION

Spray & Stripe Speci cations 1

Safety Warnings

2-6

GETTING STARTED

Flushing 7

Daily Maintenance 8

Pressure Relief Procedure 9

Setting Up to Stripe or Spray 10

Starting Up 11-12

Striping Operation 13

REPAIRS/MAINTENANCE

INSTRUCTIONS

Spray Gun Operation 14

Spray Gun Troubleshooting 15

Field Troubleshooting

16

Servicing the Fluid Pump 17

Servicing the Piston Rod 18

Servicing the Suction Assembly 18

Packing Replacement 19-20

Elect. Control Board Replacement 21

Pressure Calibration of Board 21

Clutch Replacement 22

Cltuch Troubleshooting 23

PRODUCT DIAGRAMS & PARTS LISTS

Gearbox Assembly

24

Spray Gun Assembly 25

Gun Mount Assembly 25

Frame Assembly 26

Swivel Wheel Assembly 27

Suction Assembly 27

Striping Tip Guide 28

ACCESSORIES

29-30

Manufactured by: AIRLESSCO BY DUROTECH CO.

5397 Commerce Ave.,Moorpark, CA 93021

Tel: 805-523-0211 Fax: 805-523-1063

www.airlessco.com eMail: [email protected]

SUBJECT TO CHANGE WITHOUT NOTICE.

Before operating this unit, read and follow all safety warnings and

instructions related to the usage of this equipment. READ, LEARN,

and FOLLOW the Pressure Relief Procedure on Page 10 and

understand all warnings on pages 2 thru 6.

IMPORTANT WARNING !!

HANDLE THIS UNIT AS YOU WOULD A LOADED FIREARM!!

High pressure spray can cause extremely serious injury.

OBSERVE ALL WARNINGS!

All Service Procedures to be performed by an Authorized Airlessco Service Center ONLY.

NO MODIFICATIONS or alterations of any Airlessco Equipment or part is allowed.

Introduction

1

INTRODUCTION

SPECIFICATIONS:

Part # 305-385 Airlessco Spray & Stripe 3600

305-380 ALLPRO Spray & Stripe

Max Pressure 3000 PSI (170 Bar)

Max Output 0.7 GPM (2.65 Litres/min.)

Pressure Control Electronic pressure controls operate electric clutch

Max Tip 1 gun @ 0.025”

Engine

Durotech DE400 w/ automatic low oil level shutdown

The heart of the Spray & Stripe series is the time

tested and contractor proven Airlessco “LP” piston

paint pump. Designed for professional airless

line striping and paint spraying, it is used daily by

thousands of painting professionals worldwide–

with a reputation for trouble free performance

that’s unmatched in the industry.

They’re small, compact, easy to use, and quick to

clean. Even changing colors is a breeze. Stripe

with water-based paints made for traf c lines or

athletic  elds. A professional quality spray gun is

mounted on a multi-position spray arm. Great

balance and light weight make this striper ideal

for a one-man operation.

A tool-less quick release of the spray gun from

its mount lets you spray paint using stencils, or

utilize the 50' of supplied hose and the spray gun

to paint with exterior latex & enamel paints.

The Airlessco exclusive turnbuckle based

RADIUS MEMORY™ system for striping smooth

curves and circles every time.

Flexibility to handle a wide variety of applications

make the Spray & Stripe popular with cities,

school districts, and sports programs for parking

lot or athletic  eld striping, and for use as a

mobile airless spraying station. It’s perfect for

painting fences, buildings, & covering graf ti.

Engine

Durotech DE400 w/ automatic low oil level shutdown

Service Level

Up to 5000 gallons per year

clean. Even changing colors is a breeze. Stripe

with water-based paints made for traf c lines or

athletic  elds. A professional quality spray gun is

mounted on a multi-position spray arm. Great

balance and light weight make this striper ideal

A tool-less quick release of the spray gun from

its mount lets you spray paint using stencils, or

utilize the 50' of supplied hose and the spray gun

RADIUS MEMORY™ system for striping smooth

Flexibility to handle a wide variety of applications

school districts, and sports programs for parking

mobile airless spraying station. It’s perfect for

painting fences, buildings, & covering graf ti.

TIP GUARD

ALWAYS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the injection hazard and helps

prevent accidentally placing your ngers or any part of your body close to the spray tip.

SPRAY TIP SAFETY

Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch

immediately.

• ALWAYS follow the PRESSURE RELIEF PROCEDURE and then remove the spray tip to clean it.

• NEVER wipe off build up around the spray tip.

• ALWAYS remove tip & tip guard to clean AFTER pump is turned off and the pressure is relieved by following the

PRESSURE RELIEF PROCEDURE.

KEEP CLEAR OF MOVING PARTS

Keep clear of moving parts when starting or operating the sprayer. Do not put your ngers into any openings to avoid

amputation by moving parts or burns from hot parts.

Precaution is the best insurance against an accident.

When starting the engine, maintain a safe distance from moving parts of the equipment.

Before adjusting or servicing any mechanical part of the sprayer, follow the PRESSURE RELIEF PROCEDURE, and remove

the ignition cable from the spark plug to prevent accidental starting of the sprayer.

ALWAYS INSPECT SPRAYING AREA

• ALWAYS keep spraying area free from obstructions.

• ALWAYS make sure area has good ventilation to safely remove vapors and mists.

• NEVER keep ammable material in spraying area.

• NEVER spray in vicinity of open ame or other sources of ignition.

SPRAY GUN SAFETY

• ALWAYS set safety lock on the gun in "LOCKED" position when not in use and before servicing or cleaning.

• NEVER remove or modify any part of the gun.

• ALWAYS REMOVE SPRAY TIP when cleaning. Flush unit with LOWEST POSSIBLE PRESSURE.

• ALWAYS check operation of all gun safety devices before each use.

• Be very careful when removing the spray tip or hose from gun. A plugged line contains uid under pressure. If the tip or

line is plugged, follow the PRESSURE RELIEF PROCEDURE as outlined on page 10.

Safety Warnings

Keep all labels on the unit clean and readable. Replacement labels are available from the manufacturer.

LABELING

Hazardous uid or toxic fumes can cause serious injury or death if splashed in eyes or on skin, inhaled or swallowed. Know

the hazards of the uid you are using. Store & dispose of hazardous uids according to manufacturer, local, state & national

guidelines. ALWAYS wear protective eye wear, gloves, clothing and respirator as recommended by uid manufacturer.

TOXIC FLUID HAZARD

2

Safety Warnings

Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious

injury, including the need for amputation.

• NEVER point the spray gun at anyone or any part of the body.

• NEVER put hands or ngers over the spray tip. Do not use a rag or any other material over your ngers. Paint will

penetrate through material and into the hand.

• NEVER try to stop or deect leaks with your hand or body.

• NEVER try to "blow back" paint, this is not an air spray sprayer.

• ALWAYS have gun tip guard in place when spraying.

• ALWAYS lock gun trigger when you stop spraying.

• ALWAYS remove tip from the gun to clean it.

• ALWAYS follow the PRESSURE RELIEF PROCEDURE, as shown on page 10, before cleaning or removing the

spray tip or servicing any system equipment.

• ALWAYS Be sure equipment safety devices are operating properly before each use.

• ALWAYS tighten all uid connections before each use.

MEDICAL TREATMENT

If any uid appears to penetrate your skin, get EMERGENCY CARE AT ONCE. DO NOT TREAT AS A SIMPLE CUT.

* Go to an emergency room immediately.

* Tell the doctor you suspect an injection injury.

* Tell him what kind of material you were spraying with and have him read NOTE TO PHYSICIAN.

HIGH PRESSURE SPRAY CAN CAUSE EXTREMELY SERIOUS INJURY.

OBSERVE ALL WARNINGS.

MEDICAL ALERT - Airless Spray Wounds NOTE TO PHYSICIAN:

If any uid appears to penetrate your skin, get Injection in the skin is a traumatic injury.

EMERGENCY MEDICAL CARE AT ONCE. DO It is important to treat the injury surgically

NOT TREAT AS A SIMPLE CUT. Tell the doctor as soon as possible. DO NOT DELAY treatment

exactly what uid was injected. Have him read to research toxicity. Toxicity is a concern with

the following "NOTE TO PHYSICIAN". some exotic coatings injected directly into the

bloodstream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

INJECTION HAZARD

GENERAL PRECAUTIONS

• NEVER alter equipment in any manner. • NEVER smoke while in spraying area.

• NEVER spray highly ammable materials. • NEVER use around children.

• NEVER allow another person to use sprayer unless they are thoroughly instructed on safety use and

given this operators manual to read.

• ALWAYS wear a spray mask, gloves and protective eye wear while spraying.

• ALWAYS ensure re extinquishing equipment is readily available and properly maintained.

NEVER LEAVE SPRAYER UNATTENDED WITH PRESSURE IN THE SYSTEM.

FOLLOW PRESSURE RELIEF PROCEDURES ON PAGE 10.

3

AVOID COMPONENT RUPTURE

This sprayer operates at 2500 psi (170 bar). Always be sure that all components and accessories have a

maximum working pressure of at least 3000 psi to avoid rupture which can result in serious bodily injury

including injection and property damage.

• NEVER leave a pressurized sprayer unattended to avoid accidental operation of it which could result in serious

bodily injury.

• ALWAYS follow the PRESSURE RELIEF PROCEDURE whenever you stop spraying and before adjusting,

removing or repairing any part of the sprayer.

• NEVER alter or modify any part of the equipment to avoid possible component rupture which could result in

serious bodily injury and property damage.

• NEVER use weak, damaged or non-conductive paint hoses. Do not allow kinking or crushing of hoses or allow

it to vibrate against rough, sharp or hot surfaces. Before each use, check hoses for damage and wear and ensure

all uid connections are secure.

• REPLACE any damaged hose. NEVER use tape or any device to mend the hose.

• NEVER attempt to stop any leakage in the line or ttings with your hand or any part of the body. Turn off the

unit and release pressure by following PRESSURE RELIEF PROCEDURE on page 10.

• ALWAYS use approved high pressure ttings and replacement parts.

• ALWAYS ensure re extinquishing equipment is readily available and properly maintained.

Safety Warnings

GROUNDING

Ground the sprayer and other components in the system to reduce the risk of static sparking, re or

explosion which can result in serious bodily injury and property damage.

Always ground all of these components:

• Fluid Hose: use only grounded hoses.

• Spray gun or dispensing valve: grounding is obtained through connection to a properly

grounded uid hose and pump.

• Object being sprayed: according to your local code.

• All solvent pails used when ushing should only be metal pails which are conductive.

Once each week, check electrical resistance of hose (when using multiple hose assemblies, check

overall resistance of un-pressurized hose must not exceed 29 megohms (max) for any coupled length

or combination of hose lengths. If hose exceeds these limits, replace it immediately.

Never exceed 300 Ft. (150 m.) overall combined hose length to assure electrical continuity.

Do not use halogenated solvents in this system. The prime valve, 2 gun manifold and most

airless guns have aluminum parts and may explode. Cleaning agents, coatings, paints or

adhesives may contain halogenated hydrocarbon solvents. DON'T TAKE CHANCES!

Consult your material suppliers to be sure. Some of the most common of these solvents are:

Carbontetrachloride, Chlorobenzene, Dichloroethane, Dichloroethyl Ether, Ethylbromide,

Ethylchloride, Tethrachloethane. Alternate valves and guns are available

if you need to use these solvents.

4

WHEN ADDING FUEL

• Turn engine OFF and let engine cool at least 2

minutes before removing gas cap.

• Fill fuel tank outdoors or in well ventilated area.

• Do not overll fuel tank. Fill tank to

approximately1 inches below top of neck to

allow for fuel expansion.

• Keep gasoline away from sparks, open ames,

pilot lights, heat and other ignition sources.

• Check fuel lines, tank, cap and ttings frequently

for cracks or leaks. Replace if necessary.

PREVENT STATIC SPARKING FIRE/ EXPLOSIONS

ALWAYS be sure all equipment and objects being sprayed are properly grounded. Always ground sprayer, paint

bucket and object being sprayed. See "grounding" on page 4 for detailed grounding information.

Vapors created when spraying can be ignited by sparks. To reduce the risk of re, do not plug in or unplug any

electrical cords in an enclosed spray area,. This can create sparks when there is any chance of igniting vapors still

in the air. Follow the coating & solvent manufacturers safety warnings and precautions.

Use only conductive uid hoses for airless applications. Be sure gun is grounded through hose connections. Check

ground continuity in hose & equipment. Overall (end to end) resistance of un-pressurized hose must not exceed 29

megohms for any coupled length or combination of hose length. Use only high pressure airless hoses with static

wire approved for 3000 psi.

WHEN SPRAYING & CLEANING WITH FLAMMABLE PAINTS OR PAINT THINNERS:

1. When spraying with ammable liquids, unit must be located a minimum of 25 feet away from spraying area

in a well ventilated area. Ventilation must be sufcient enough to prevent the accumulation of vapors.

2. To eliminate electrostatic discharge, ground the spray unit, paint bucket and spraying object. Use only high

pressure airless hoses approved for 3000 psi which is conductive.

3. Remove spray tip before cleaning gun and hose. Make contact of gun with bucket and spray without the tip in

a well ventilated area, into the grounded steel bucket.

4. Never use high pressure in the cleaning process. USE MINIMUM PRESSURE.

5. Do not smoke in spraying/cleaning area.

GAS ENGINE PRECAUTIONS

Important: United States Government safety standards have been adopted under the Occupational

Safety & Health Act. These standards, particularly the General Standards, Part 1910, & the

Construction Standards, part 1926 should be consulted.

FLUSHING

Reduce risk of injection injury, static sparking or splashing by following the specic cleaning procedure on page 7.

• ALWAYS follow the PRESSURE RELIEF PROCEDURE on page 10.

• ALWAYS remove the spray tip before ushing. Hold a metal part of the gun rmly to the side of a metal pail and

use the lowest possible uid pressure during ushing.

• NEVER use cleaning solvents with ash points below 140º F. Some of these are: acetone, benzene, ether,

gasoline and naphtha. Consult your supplier to be sure.

• NEVER smoke in the spraying/cleaning area.

Safety Warnings

WHEN STARTING ENGINE

• Make sure spark plug, mufer, fuel cap and air cleaner

are in place.

• Do not crank engine with spark plug removed.

• If fuel spills, wait until it evaporates before starting

engine.

• If engine oods, set choke to OPEN/RUN

position, place throttle in FAST and crank until

engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip engine or equipment at angle which

causes gasoline to spill.

5

Gasoline & its vapors are extremely

ammable & explosive.

Fire or explosion can cause severe burns or death.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY or with fuel shut-off

valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH

FUEL IN TANK

• Store away from furnaces, stoves, water heaters and

other appliances that have pilot lights or other ignition

source. They can ignite gasoline vapors.

Starting engine creates sparking.

Sparking can ignite nearby ammable gases.

Explosion and re could result.

• If there is natural or LP gas leakage in area, do not

start engine.

• Do not use pressurized starting uids because vapors

are ammable.

Rapid retraction of starter cord (kickback) will pull

hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

• When starting engine, pull cord slowly until resistance is

felt, then pull rapidly.

• Remove all external equipment/engine loads before starting

engine.

• Direct coupled equipment components such as, but not

limited to, blades, impellors, pulleys, sprockets, etc. must

be securely attached.

Rotating parts can contact or entangle hands, feet,

hair, clothing or accessories.

Traumatic amputation or severe laceration can result.

• Operate equipment with guards in place.

• Keep hands and feet away from rotating parts.

• Tie up long hair and remove jewelry.

• Do not wear loose tting clothing, dangling drawstrings or

items that could become caught.

Engines give off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if doors or

windows are open.

Safety Warnings

Running engines produce heat. Engine parts,

especially mufers, become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush,

etc. can catch re.

• Allow mufer, engine cylinder and ns to cool before

touching.

• Remove accumulated combustibles from mufer area and

cylinder area.

• Install and maintain in working order a spark arrester

before using equipment on forest covered, grass covered

and brush covered unimproved land. The state of

California requires this (Section 4442 of the California

Public Resources Code). Other states may have similar

laws. Federal laws apply on federal land.

Unintentional sparking can result in re

or electric shock.

Unintentional start up can result in entanglement,

traumatic amputation, or lacerations.

BEFORE PERFORMING ADJUSTMENTS OR

REPAIRS

• Disconnect spark plug wire and keep it away from

spark plug.

• Disconnect battery at negative terminal (only

engines with electric start).

WHEN TESTING FOR SPARK

• Use approved spark plug tester.

• Do not check for spark with spark plug removal.

6

1. New Sprayer

Your Airlessco unit was factory tested in an antifreeze solution which was left in the pump.

Before using oil-base paint, ush with mineral spirits only. Before using water-base paint

ush with soapy water, then do a clean water ush.

2. Changing Colors

Flush with a compatible solvent such as mineral spirits or water.

3. Changing from Water-Base to Oil-Base Paint

Flush with soapy water, then mineral spirits.

4. Changing from Oil-Base to Water-Base Paint

Flush with mineral spirits, followed by soapy water, then do a clean water ush.

5. Storage

Oil-base paint: Flush with mineral spirits.

Water-base paint: Flush with water, then mineral spirits and leave the pump, hose and gun

lled with mineral spirits. For longer storage, use mixture of mineral spirits and motor oil

(half & half). Shut off the sprayer, follow Pressure Relief Procedure on page 10

Flushing

Read prior to using your sprayer

7

8

1. Keep the displacement pump packing nut/wet cup lubricated with Airlessco TSO

(Throat Seal Oil) at all times. The TSO helps protect the rod and the packings.

Daily Maintenance

Airlessco Throat Seal Oil

6 ounce bottle Part # 188-187

1 quart bottle Part # 188-392

2. Inspect the packing nut daily. Your pump has Airlessco’s patented Triple Life Packing System.

Packing life will be extended a minimum of three times if the

following "Packing Adjustment" procedure is followed:

If seepage of paint into the packing nut and/or movement of the piston upward is found (while not

spraying), the packing nut should be tightened enough to stop leakage only, but not any tighter.

Overtightening will damage the packings and reduce the packing life.

3. Check suction nut daily.

9

Pressure Relief Procedure

IMPORTANT!

To avoid possible serious body injury, always follow this procedure whenever the

sprayer is shut off, when checking it, when installing, changing or cleaning tips,

whenever you stop spraying, or when you are instructed to relieve the pressure.

1. Engage the gun safety latch. Refer to the

separate instruction manual provided with

your gun on its safety features and how to

engage safety latch.

4. Turn Prime/Pressure Relief Valve (PR Valve)

to the open (priming) position to relieve

residual uid pressure.

There will be a wider gap between valve

handle and cam body when in open

position. In the closed position there is

only a very slight gap.

.

Note: The valve handle can move both

clockwise and counter clockwise and can

face different directions.

2. Turn the unit off.

3. Disengage the gun safety latch and trigger

the gun to relieve residual uid pressure.

Hold metal part of the gun in

contact with grounded metal pail.

USE MINIMUM PRESSURE !

5. Re-engage gun safety latch and

close Prime/Pressure Relief Valve.

If the SPRAY TIP OR HOSE IS CLOGGED, follow Step 1 through 5 above. Expect paint

splashing into the bucket while relieving pressure during Step 4.

If you suspect that pressure hasn't been relieved due to damaged Prime/Pressure

Relief Valve or other reason, engage the gun safety latch and take your unit to an

authorized Airlessco Service Center.

10

Setting Up to Stripe or Spray

1. Connect the hose and gun.

a. If the hose is not already installed on the striper,

remove the plastic cap plug from the outlet tee

at the spray pump, and screw a conductive or grounded

3000 psi airless spray hose onto  uid outlet.

b. Connect an airless spray gun to the other end of

the hose.

c. Do not use steel braided airless hose. Use nylon

braided airless hose only.

NOTE: Do not use thread sealer on swivel

unions as they are made to self-seal.

Use thread seal on tapered male threads only.

3. Grounding

A small steel chain grounding strap is installed at

the factory to prevent static build-up.

4. Flush the sprayer

As per "Flushing Procedure" in this manual.

2. Remove the snap-on cover plate

over the piston.

WARNING

To reduce the risk of static sparking,  re or

explosion which can result in serious bodily

injury and property damage, always ground

the sprayer and system components and the

object being sprayed, as instructed in the

safety warning section of this manual.

3. Fill the packing nut/wet cup with 5 drops

of Airlessco Throat Seal Oil (TSO) and

then reinstall snap-on piston cover plate

Failure to lubricate the piston properly

with throat seal oil can cause premature

wear and damage to piston and packings.

11

Starting Up

4. Adjusting the Pressure

a. Turn the Pressure Control Knob Clockwise to

increase pressure and counterclockwise to decrease

pressure.

b. Always use the lowest pressure necessary to

completely atomize the material.

Note: Operating the sprayer at higher pressure

than needed, wastes material, causes early tip

wear, and shortens sprayer life.

c. If more coverage is needed, use a larger tip rather

than increasing the pressure.

d. Check the spray pattern. The tip size and angle

determines the pattern width and ow rate.

When you spray into the paint bucket,

always use the lowest spray pressure

and maintain rm metal to metal contact

between gun and container.

To stop the unit in an emergency, turn the

engine off. Then relieve the uid pressure

in the pump and hose as instructed in the

Pressure Relief Procedure.

Follow the "Pressure Relief Procedure".

To reduce the risk of injection, never hold

your hand, body, ngers or hand in a rag

in front of the spray tip when cleaning

or checking for a cleared tip. Always

point the gun toward the ground or into a

waste container when checking to see if

the tip is cleared or when using a

self-cleaning tip.

1. Learn the Functions

of the Controls.

2. Prepare the Material

a. Prepare the material according to the material

manufacturer's recommendations.

b. Place the suction tube into the material

container.

PRESSURE CONTROL KNOB is used to adjust

pressure. Turn clockwise (CW) to increase pressure

and counterclockwise (CCW) to

decrease pressure.

PRIME/PRESSURE (PR) RELIEF VALVE is used to

prime pump and to relieve pressure from gun, hose and tip.

Prime/Pressure Relief Valve (Prime/PR Valve)

Used to relieve pressure from gun, hose & tip and to prime

the unit when in OPEN position. (It is in open position

when there is a wider gap

between valve handle and

cam body)

When in CLOSED position,

there is only a very slight gap

between handle & body.

When closed the system is

pressurized. Handle as a loaded rearm!

3. Starting the Sprayer

a. Prime/PR Valve must be "OPEN" in the priming

position.

b. When you have ensured that the gun safety latch

is engaged, attach tip and safety guard.

c. Turn the engine ON/OFF switch to the "ON"

position. Pull rope vigorously until engine

starts.

d. Turn Pressure Control Knob clockwise to prime

the pump.

e. After the pump is primed, turn Prime/PR Valve to

the "Closed" position.

f. Turn Pressure Control Knob to the desired spray

pressure.

g. Disengage the gun safety latch and you are

ready to spray.

12

5. When Shutting off the Sprayer

a. Whenever you stop spraying, even for a short break,

follow the "Pressure Relief Procedure".

b. Clean the tip & gun as recommended in the seperate

Gun Manual supplied with the gun/

c. Flush the sprayer at the end of each work day, if the

material you are spraying is water-based, or if it could

harden in the sprayer overnight. See "Flushing". Use a

compatible solvent to ush, then ll the pump and hoses

with an oil based solvent such as mineral spirits.

d. For long term shutdown or storage, refer to the

"Flushing" section of this manual.

Be sure to relieve pressure in

the pump after lling with Airlessco

Pump Conditioner.

Avoiding Tip Clogs

There is an easy way to keep the outside of the

tip clean from material build up:

Every time you stop spraying, for even a minute,

lock the gun and submerge it into a small bucket

of thinner suitable for the material sprayed.

Thinner will dissolve the buildup of paint on the

outside of tip, tip guard and gun much more

effectively if the paint doesn't have time to dry

out completely.

Starting Up

1. Choose handle location

The choices are, installing the handle opposite of the

single wheel assembly (standard set up) or placing

the handle directly over the single wheel assembly.

The handle location is really a matter of personal

preference, however having the handle away from

the single wheel assembly allows for easier loading/

unloading from a van or truck.

2. Cable Tension Adjustment

Once the handle and gun arm assemblies are set up to

the preferred positions, pressurize the unit and trigger

each gun to ensure that they activate and release

correctly. If not, adjust the cable tension as follows:

a. Locate the adjustment knobs on the base of the

gun trigger, where the cable connects to the gun

trigger assembly.

b. Loose the locking nut & move the adjusting screw

until the slack has been removed from the cable.

c. Tighten locking nut and retest gun triggers for

proper function.

Note: There is an additional cable adjustment

where the cable attaches to the gun holder

assembly. Use only if the gun trigger adjustment

is insuf cient.

3. Miscellaneous Operations

CURBS: To paint at a 90 degree angle to spray the

sides of curbs install a part # 032-028 swivel between

gun head and tip guard and aim guard sideways

towards the curb.

WIDE STRIPES: Install wider fan striping tips and

raise the gun height to achieve the desired width line.

STENCILS: Install standard spray tip on the outer

gun. Rotate gun to remove from the gun holder and

use the gun to spray within your stencils. Use of an

extension pole will make this job a lot easier on the

operators back and is highly reccomended.

STANDARD PAINTING: Install the appropriate

size and type of paint spraying tip (standard paint

spray, “W” wide pattern, or “Fine Finish”). Remove

gun and spray just as you do for stencils. Additional

paint hose may be required depending on the

distance between the job and the equipment.

Striping Operation

13

4. Setting the Swivel Wheel with RADIUS MEMORY

™

Refer to  gure below

a. Pull back on the swivel wheel trigger to adjust the

wheel to desired angle.

b. To set the angle for constant arch loosen the jam

nuts on the Turnbuckle. Place Turnbuckle onto

the mounting nub located on the striper frame.

Adjust the turnbuckle until it  ts over the mounting

nub located on the wheel frame. Tighten jam nuts

on the turnbuckle to af x the length.

Note: If you have archs that you paint regularly, purchase

additional Turnbuckles (P.N. 136-163) and keep them set to

those arc sizes for easy use.

Mounting Nubs

Turnbuckle

Wheel Release

Spray Gun Operation

Reversible

Spray Tip

Tip Guard

Trigger Guard

MAJOR COMPONENTS OF SPRAY GUN &

REVERSIBLE REV-TIP

™

SPRAY GUN

Attach spray gun to airless unit and tighten ttings securely.

Set the gun safety latch. (Also may be called gun safety

lock, or trigger lock)

* The gun safety latch should always be set when the gun is

not being triggered.

Read all warnings and safety precautions supplied with the

spray gun and in product manual.

SPRAY TIP ASSEMBLY

1. Be sure the pressure relief procedure is followed

before assembling tip and housing to the gun.

2. Insert REV-TIP™ cylinder into the REV-GUARD

(guard housing assembly).

3. Guide the metal seat into REV-GUARD™ (guard

housing assembly) through the retaining nut & turn

until it seats against the cylinder.

4. Insert the O-Ring gasket onto the metal seat so that it

ts into the grooves.

5. Finger tighten REV-GUARD™ retaining nut onto the gun.

6. Turn guard in the desired position.

7. Completely tighten the retaining nut.

TO REMOVE CLOGS FROM SPRAY TIP

1. Lock gun safety latch.

2. Turn REV-TIP™ handle 180 degrees.

3. Disengage trigger lock and trigger gun into

the pail.

4. If the REV-TIP™ handle appears locked

(resists turning), loosen the retaining nut. The

handle will now turn easily.

5. Engage gun safety latch and return handle to

the spray position.

CLEANING SPRAY GUN

CLEANING FILTER IN GUN HANDLE

Immediately after the work is nished, ush the gun out

with a solvent. Brush pins with solvent and oil them

lightly so they will not collect dried paint.

To clean the lter, use a brush dipped in an

appropriate solvent. Change or clean lters

at least once a day. Some types of latex may

require a lter change after four hours of

operation.

Gun Handle. Unscrew

from gun head to service

lter inside.

Gun Safety

Latch or Lock

™

14

Press up here & pull gently

to remove trigger guard

O-Ring Gasket

Metal Seat

REV-TIP™ Cylinder

Retaining Nut

Spray Position Shown

Reverse to

Unplug

REV-GUARD™

Guard Housing Assembly

Retaining Nut

Part # 561-026

Part # 561-029

Part # 561-XXX

G Thread 7/8" 561-002

F Thread 11/16" 561-001

Spray Gun Troubleshooting

DEFECTS CAUSE CORRECTION

Coarse spray Low pressure Increase the pressure

Excessive fogging High pressure Reduce pressure for satisfactory pattern

(overspray) Material too thin Use less thinner

Pattern too wide Spray angle too large Use smaller spray angle tip

Pattern too narrow Spray angle too small Use larger spray angle tip. (If coverage is OK,

try tip in same nozzle group)

Too much material Tip size too large Use next smaller tip

Material too thin

Pressure too high Reduce pressure

Too little material Tip size too small Use next larger tip

Material too thick

Thin distribution in Worn tip Change for new tip

center of pattern Wrong tip Use tip with a smaller spray angle

"horns"

Thick skin on work Material too viscous Thin material

Application too heavy Reduce pressure and/or use smaller tip

Coating fails to Material too viscous Thin material

close & smooth over

Spray pattern irregular, Orice clogged Clean carefully

deected Tip damaged Replace with new tip

Craters or pock marks Solvent balance Use 1-3% "short" solvents remainder "long"

solvents. (This is most likely to happen with

material of low viscosity, lacquers etc.)

Bubbles on work Contamination or dust Clean surface to be sprayed

Clogged screens Extraneous material Clean screen

in paint.

Coarse pigments Use coarse screen if orice size allows

Poorly milled pigments Use coarser screen, larger orice tips. Obain ball

(paint pigments glocculate milled paint. If thinner was added, test to see if a

cover screen. Incompatible drop on top of paint mixes or attens out on

paint mixture & thinners. on the surface. If not, try different thinner

in fresh batch of paint.

TEST THE PATTERN

15

Field Troubleshooting

PROBLEM CAUSE SOLUTION

Unit doesn't prime Airleak due to:

• Loose Suction Nut • Tighten Suction Nut

• Worn O-Rings • Replace O-Ring (106-011) on

suction seat, & O-Ring (106-

020) below suction seat

• Hole in Suction Hose • Replace Suction Hose (331-290)

Stuck or Fouled Balls Service outlet valve suction

assembly

Unit primes but has no Pressure set too low Turn up pressure

or poor pressure

Filter(s) are clogged Clean or replace gun lter, inlet

lter and/or manifold lter

Outlet Valve fouled/worn Service outlet valve

Prime/Pressure Relief valve Clean or replace prime valve

bypassing

Packings and/or piston worn • Tighten packing nut

• Repack unit

Unit does not maintain Blown spray tip Replace spray tip

good spraying pressure

Packings and/or piston worn Repack unit

Upper Seat worn Replace upper seat

16

17

Refer to Figure 1

1. Follow the Pressure Relief Procedure on page 10.

2. Flush the material you are spraying out of the machine.

3. Remove the connecting rod shield (331-111).

4. Move the piston rod (331-093) to its lowest position

by cycling pump slowly.

5. Remove the retaining ring (331-062) from the

connecting rod (331-038) and slide the sleeve (331-

117) down revealing the connecting rod pin (331-065).

6. Remove the suction tube assembly from the uid

pump (331-209) by unscrewing the suction nut

(331-034) with the packing adjustment tool.

7. Using a 1/2” wrench unscrew the two bolts (100-318)

from the cover assembly (331-234). The uid pump

(331-209) will be hanging loosely at this point.

8. Remove the connecting rod pin (331-065) out of

the connecting rod (331-038), allowing the removal

of the uid pump (331-209) from the machine.

FIGURE 1

Servicing the Fluid Pump

Fluid Pump Disconnect

Fluid Pump Reinstall

Refer to Figure 1 & 4

1. Loosen the packing nut and ensure that the piston rod

(331-093) is in its upper position in the uid pump body

(331-011). Slip the sleeve (331-117) & the retaining

ring (331-062) over the piston rod.

2. Push the piston rod up into the connecting rod (331-

038) & align the holes. Insert the connecting rod pin

(331-065) through the connecting rod & piston. Slip

the sleeve up over the connecting rod pin and insert

the retaining ring into the groove on the connecting rod.

3. Push the two bolts (100-318) through the tube spacers

(331-074) & screw them into the cover assembly (331-

234). Using a 1/2” wrench, tighten the two bolts evenly

(alternating between them) until you reach 20 ft-lbs.

4. Reassemble lower suction valve assembly by placing

the suction seat (331-409), O-ring (106-011), suction

ball (331-030) & suction ball guide (331-029) in the

suction nut (331-034) & screw onto uid pump body.

5. Start the machine and operate slowly to check the piston

rod for binding. Adjust the two bolts, holding the uid

pump body to the cover assembly, if necessary. This

will eliminate any binding.

6. Tighten the packing nut clockwise until resistance is

felt against the Belleville Springs, then go 3/4 of a turn

more. Put ve drops of Airlessco Throat Seal Oil into the

packing nut.

7. Run the machine at full pressure for several minutes.

Release the pressure by following the Pressure Relief

Procedure & readjust the packing nut per step 6 above.

8. Install the connecting rod shield (331-111) so that the

small hole is in the upper right hand corner.

331-209

Servicing the Piston Rod - Outlet Valve

331-196

331-195

Piston

DISASSEMBLY OF THE OUTLET VALVE

REFER TO FIGURE 3

1. Disconnect the Fluid Pump following instructions on page 17 .

2. Place piston holder (331-195) in a vise. Slide piston into

the holder & lock in place with a 3/8” dowel (331-196).

3. Use a 1/4” allen wrench to unscrew the outlet seat retainer

(331-026) from the piston.

4. Remove the outlet seat (331-026), O-ring (331-100) and

outlet ball (331-027).

5. Inspect outlet ball & seat for wear. Replace as necessary.

6. While piston is still locked in the holder, install parts

back into the piston in the following order:

ball, outlet seat and O-ring

Before reinstalling the outlet seat support, apply two drops of

Loctite No. 242 (blue) on the threads & torque to 20 ft-lbs.

Servicing the Suction Assembly

REFER TO FIGURE 4

1. Un-thread and remove suction nut from the  uid pump body.

2. Remove suction seat (331-409), O-ring (106-011), suction ball

(331-030) and suction retainer (331-029).

3. Clean all parts and inspect them for wear or damage, replacing

parts as needed.

4. Clean inside of the  uid pump body.

5. Reassemble lower suction valve assembly by placing the

suction seat (331-409), O-ring (106-011), suction ball (331-030)

& suction ball guide (331-029) in the suction nut (331-034) &

FIGURE 3

FIGURE 4

18

NOTE: Airlessco LP pump tool kit 188-197 is suggested for this task.

Kit includes: Packing Tightening Bar (189-211), Packing Removal Tool (331-153),

Piston Holder (331-195), 3/8” dowel (331-196).

Page is loading ...

LG Electronics 3600 User manual

LG Electronics 3600 User manual

Other documents